|
2.04 TIMECLOCKS
<br /> 2.03 WIREWAYS: Square D Class 5100 Type LDB for dry locations or Square 3.03 WIRE MARKERS: Provide wire and cable markers at panelboard gutters, A. Tork DZS series unless indicated otherwise. 3.07 INSTALLATION OF ROOM CONTROLLERS AND PLUG LOAD CONTROLLERS
<br /> D Class 5100 Type LDR for damp and wet locations unless indicated pull boxes, outlet boxes, and junction boxes for each load B. Input Voltage: Coordinate with the voltage of the control A. Install controllers in concealed accessible locations above B. Make conduit connections to equipment using flexible conduit.
<br /> otherwise; size as required by NFPA 70 based on conductor fill and connection. Indicate branch circuit or feeder number indicated on circuit. ceilings. Use liquidtight flexible conduit with watertight connectors in ,►
<br /> bending radius requirements. Drawings and control wire number indicated on shop drawings. C. Enclosure: Manufacturer's standard enclosure suitable for the B. Do not switch power serving controllers. All required damp or wet locations.
<br /> 3.04 COLOR CODE LEGEND: Provide identification label identifying environment in which the timeclock is installed. switching shall occur on the load side of the controller C. Connect heat producing equipment using wire and cable with
<br /> PART 3 EXECUTION conductor color codes at each piece of feeder or branch-circuit 2.05 TIMER SWITCHES: Tork #SS403 unless indicated otherwise. relay(s). insulation suitable for temperatures encountered.
<br /> 3.01 INSTALLATION distribution equipment. 2.06 OUTDOOR PHOTOCELLS: Tork #2101 unless indicated otherwise. C. Provide nameplate for each controller indicating rooms) D. Provide receptacle outlet to accommodate connection with
<br /> A. Conceal all conduit in all interior and exterior areas, 3.05 INSTALLATION 2.07 INDOOR SWITCHING PHOTOSENSORS controlled. attachment plug. 40.
<br /> mr
<br /> including exposed structure areas, unless the Architect A. Install nameplates and labels parallel to equipment lines. A. Sensor: Wattstopper #LS-102 unless indicated otherwise. D. Install room controller wall-mounted switches 46 inches above E. Provide cord and cap where field-supplied attachment plug is
<br /> provides specific approval permitting the use of exposed B. Secure nameplates for distribution equipment visible to the B. Power Pack: Wattstopper #BZ-150 unless indicated otherwise. finished floor to the centerline of the box unless indicated required.
<br /> conduit. public to the inside surface of door. C. Finish: White. otherwise. F. Install suitable strain-relief clamps and fittings for cord
<br /> B. Route any exposed conduit parallel and perpendicular to walls. C. Secure nameplates for distribution equipment not visible to 2.08 INDOOR 0-10 VOLT DIMMING PHOTOSENSORS 3.08 CLOSEOUT
<br /> the ublic to the front of the enclosure usin screws, rivets, connections at outlet boxes and equipment connection boxes.
<br /> P 9 A. Sensor: Wattstopper #LS-301 unless indicated otherwise. A. Demonstrate proper operation of lighting control devices to G. Install disconnect switches, controllers, control stations,
<br /> C. Subject to the Architect's approval , conduit located above or adhesive. B. Power Pack: Wattstopper #BZ-150 unless indicated otherwise. the Owner and correct deficiencies or make adjustments as and control devices to complete equipment wiring
<br /> ceilings is permitted to be routed point-to-point provided it END OF SECTION C. Finish: White. directed. requirements.
<br /> is secured and supported per NFPA 70 requirements and complies D. Configuration Tool: Wattstopper #ESR-301-S unless indicated B. Train Owner s personnel on operation, adjustment, programming, H. Install terminal block jumpers to complete equipment wiring 0
<br /> with all applicable Codes and other requirements of the SECTION 260595 - FIRE STOPPING otherwise. and maintenance of lighting control devices. requirements.
<br /> specifications. E. Remote Control: Wattstopper #ESR-301-P unless indicated C. Provide a written report of all program settings and I. I O 2020 STARBUCKS COFFEE COMPANY
<br /> D. Do not embed conduit in slabs-on-grade. Locate conduit a PART 1 GENERAL otherwise. photosensor settings to the Owner.
<br /> minimum of 2 inches below the bottom surface of the slab to 1.01 PREPARATION: Examine the com lete set of Drawin s and identif all equipment to complete equipment wiring requirements.
<br /> P 9 Y 2.09 DISTRIBUTED LIGHTING CONTROL SYSTEMS END OF SECTION J. Cut and seal conduit openings in freezer and cooler
<br /> A. Room Controllers:1. Switching: SECTION 262416 - PANELBOARDS walls, 0
<br /> avoid future damage from cutting of the floor slab. fire rated partitions, floors and assemblies and identify
<br /> I AR
<br /> E. Route conduit in slabs-above-grade from point-to-point. Do appropriate firestopping method for the assembly. floors, and cengs where applicable.
<br /> not cross conduits embedded i n s I abs.
<br /> a. Single-Relay: Wattstopper #LMRC-101 un I ess END OF SECTION 2401 UTAH AVENUE SOUTH
<br /> F. Route underground conduit from point-to-point and at a burial PART 2 PRODUCTS indicated otherwise. PART 1 GENERAL - NOT USED SECTION 262726 - WIRING DEVICES SEATTLE, WASHINGTON 98134
<br /> depth in compliance with NEPA 70, local code, and utility 2.01 FIRESTOPPING ASSEMBLIES: Use only systems listed by UL or FM or b. Dual-Relay: Wattstopper #LMRC-102 unless
<br /> company requirements. tested in accordance with ASTM E 814 or ASTM E 119 that have F indicated otherwise. PART 2 PRODUCTS PART 1 GENERAL (206) 318-1575
<br /> G. Arrange conduit to maintain headroom and present neat Rating equal to fire rating of penetrated assembly and minimum T 2. 0-10 Volt Dimming: 2.01 LIGHTING AND APPLIANCE PANELBOARDS 1.01 PREPARATION: Contact the Architect to determine colors of all
<br /> appearance and arrange supports to prevent m i sa I i gnment during Rating Equa I to F Rating.
<br /> a. Single-Relay: Wattstopper #LMRC-211 un I ess A. Descr i pt ion: Square D Type NQ for 240 Vo I t C I ass and Square D THESE DRAWINGS AND THE PROJECT MANUAL
<br /> wiring installation. 2.02 MATERIALS: Elastomeric silicone firestopping, foam firestopping, indicated otherwise. Type NF for 600 Volt Class unless indicated otherwise. wiring devices, cover plates, and carpet and the flanges, locations
<br /> where sta i n I ess stee I cover p I ates are required, and I ocat i ons where ARE CONFIDENTIAL AND SHALL REMAIN THE
<br /> H. Secure and support all conduit in compliance with NFPA 70 fibered compound firestopping, fiber packing material , mechanical b. Dual-Relay: Wattstopper #LMRC-212 unless B. Voltage, Phase, and Current Ratings: As indicated or carpet and the flanges are required. SOLE PROPERTY OF STARBUCKS
<br /> requirements and group adjacent conduits on steel channel firestop devices, intumescent putty, and firestop pillows are indicated otherwise. otherwise required.
<br /> racks and trapezes. permitted. C. Three-Relay: Wattstopper MRC-213 un I ess C. Short-C i rcu i t Current Rat i n SCCR No I ess than the CORPORATION,WHICH IS THE OWNER OF THE
<br /> PP #L 9 ( ) PART 2 PRODUCTS
<br /> I. COPYRIGHT IN THIS WORK. THEY SHALL NOT BE
<br /> Provide 12 inches of clearance between conduit and piping or indicated otherwise. available fault current. The Contractor shall determine the 2.01 RECEPTACLES
<br /> surf aces w i th temperatures exceeding 104 degrees F. PART 3 EXECUTION 3. Forward Phase D i mming: ava i I ab I e f au I t current where not i nd i sated on the Draw i n s. REPRODUCED(IN WHOLE OR IN PART), SHARED
<br /> J. Install no more than a uivalent of three 90 de ree bends 3.01 INSTALLATION g A. All Receptacles:
<br /> q 9 a. S i ng I e-Re I ay: Wattstopper #LMRC-221 un I ess D. Bussing: As indicated. 1. Co I or as se I ected by Architect. WITH THIRD PARTIES OR USED IN ANY MANNER
<br /> between boxes. A. Comp I y w i th firestopping manufacturer s recommendations for i nd i sated otherwise. E. Bonded E u i ment Ground Bar: Provide for each ane I board. ON OTHER PROJECTS OR EXTENSIONS TO THIS
<br /> K. Provide sleeves when penetrating footings, masonry walls and temperature and other environmental conditions before, during, q P P 2. Provide tamper-resistant receptacles where denoted TR
<br /> b. Dual-Relay:I-Re I ay: Wattstopper #LMRC-222 un I ess F. Iso I ated Ground Bar: Provide for each pane I board that serves on the Drawings and otherwise required. PROJECT WITHOUT THE PRIOR WRITTEN
<br /> f I oors and sea I a I I penetrations through footings and f I oors and after i nsta I I at i on. Provide vent i I at i on i n areas where i nd i sated otherwise. i so I ated ground I oads. 3. Provide ground-f au I t c i rcu i t i nterrupter receptac I es CONSENT OF STARBUCKS CORPORATION.
<br /> water t i ght. so I vent-cured mater i a I s are being i nsta I I ed. B. P I ug Load Contro I I ers: Wattstopper #LMPL-101 un I ess i nd i sated G. Enclosure: Manufacturer's standard enc I osure su i tab I e for the where denoted "GFCI" on the Drawings and otherwise THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> L. Provide suitable fittings to accommodate expansion and B. Protect adjacent surfaces from damage by material otherwise. environment in which the panelboard is installed; 5.75 inches required.
<br /> def I est i on where condu i t crosses seismic, contro I , and i nsta I I at i on. C. Occu anc Sensors: dee 20 i nches w i de un I ess i nd i sated otherwise; surf ace or INTENDED TO EXPRESS DESIGN INTENT FOR A
<br /> P y P 4. Provide receptacles with factory-applied permanent
<br /> expansion j o i nts. C. C I can substrate surf aces of d i rt, dust, grease, o i I , I oose 1. 1-Button Wa I I Switch: Wattsto er MDW-101 un I ess f I ush mounted as i nd i sated. PROTOTYPICAL STARBUCKS STORE(WHICH IS
<br /> M. Provide suitable ull strin in each em t conduit exce t material or other matter which ma affect bond of PP � controlled receptacle marking where denoted CR on the
<br /> P 9 P Y P Y i nd i Gated otherwise; co I or as se I ected by the H. Cabinet Front: Surf ace or f I ush type as i nd i sated w i th h i nged Drawings and where contro I I ed by automat i c shutof f SUBJECT TO CHANGE AT ANYTIME)AND DO NOT
<br /> sleeves and nipples. firestopping material . Remove incompatible materials which Architect. door, flush lock, metal directory
<br /> . REFLECT ACTUAL SITE CONDITIONS. NEITHER
<br /> N. 2.
<br /> dirt and moisture. materia I I eakage. i nd i sated otherwise; co I or as se I ected b the
<br /> . y a. asosemaeyaaemaer, arenoPARTY SHALL HAVE ANY OBLIGATION NOR
<br /> I. Circuit Breakers: LIABILITY TO THE OTHER(EXCEPT STATED0. D.
<br /> 1. Bolt-on thermal-magnetic molded case circuit breakers acce table.
<br /> and unused condu i t openings. ma i nta i n the fire rating of the partition, f I oor, or ce i I i ng 3. Corner-Mount: Wattstopper #LMDX-100 un I ess i nd i Gated w i th common tri p hand I e for a I I po I es. P ABOVE) UNTIL A WRITTEN AGREEMENT IS FULLY
<br /> P. Ground and bond conduit and wirewa s as re uired b NEPA 70. assembl been enetrated. 5. Provide NEMA receptacle indicated with two integral Type
<br /> Y q Y Y 9 P otherwise. a. Provide Type SWD for I i ght i ng c i rcu i is. A, 5 ampere, 5 vo I t USB ports where denoted "USB" on the EXECUTED BY BOTH PARTIES.
<br /> END OF SECTION E. Install materials in manner described in fire test report and 4. Ceiling-Mount: Wattstopper #LMDC-100 unless indicated b. Provide Type HACR for heating, air-conditioning, Drawings.
<br /> i n accordance w i th manufacturer's i nstruct i ons, comp I ete I y otherwise. and refrigeration equipment c i rcu i is. 6. I STARBUCKS TEMPLATE VERSION: 12020-01-31.1
<br /> SECTION 260537 - BOXES closing openings. D. Wall Switches: C. Provide Class A ground-fault circuit interrupter receptacles installed outdoors.
<br /> F. Do not cover installed firestopping until inspected by 1. Multi-Button: Wattstopper LMSW-100 series unless (GFCI) where indicated or otherwise required. 7. NEMA 5-15R unless indicated otherwise.
<br /> PART 1 GENERAL - NOT USED Authority Having Jurisdiction. i nd i sated otherwise w i th number of buttons as re u i red d. Provide round-f au I t rotect i on of e u i ment ARCHITECT OF RECORD
<br /> q g P q P B. Standard NEMA 5-15R Duplex: Hubbell #BR15 unless indicated
<br /> G. Install any labeling required by Code. for the application; color as selected by the (GFPE) where serving heat tracing or otherwise otherwise. �_ " CD
<br /> PART 2 PRODUCTS H. Clean adjacent surfaces of firestopping materials. Architect. re uired. Sn > .-
<br /> 2.01 ALL BOXES END OF SECTION q C. Standard NEMA 5-20R Duplex: Hubbell #BR20 unless indicated C, > ; z
<br /> 2. Dimming: Wattstopper #LMDM-101 unless indicated e. Provide combination type arc-fault circuit otherwise. = >- o
<br /> A. Nonmetallic boxes are not permitted unless indicated otherwise otherwise; color as selected by the Architect. interrupter (AFCI) where indicated or otherwise D. Interior GFCI Duplex: Hubbell #GF20 unless indicated "C'
<br /> or without specific written approval from the Architect. SECTION 260919 - CONTACTORS AND RELAYS 3. Scene Selection: Wattstopper #LMSW-105 unless indicated required. otherwise. W
<br /> B. Provide all required box hangers and supports, extension otherwise; color as selected by the Architect. f. Provide dual-rated combination type arc-fault C'
<br /> rin s, mud rin s, etc. for a com lete and secure PART 1 GENERAL - NOT USED 1. Provide GFCI receptacles with audible alarm when the
<br /> 9 9 P E. Dimming Photosensors: circuit interrupter (AFCI) and Class A receptacle serves a sump pump.
<br /> installation. 1. For Sidelit Daylight Zones: Wattstopper #EMCs-400 ground-fault circuit interrupter (GFCI) where E. Exterior GFCI Duplex: Hubbell #GFTR20 unless indicated
<br /> C. Use gang boxes where more than one device is mounted together; PART 2 PRODUCTS unless indicated otherwise. indicated or otherwise required. otherwise.
<br /> do not use sectional boxes. 2.01 CONTACTORS 2. For To lit Da li ht Zones: Wattsto er MLS-500 unless 2. Accessories: 4mcag Pitecure
<br /> 2.02 OUTLET AND SMALL JUNCTION BOXES A. Description: Square D Class 8903, Type L or Type S unless indicated otherwgse. PP a. Provide handle ties for circuit breakers servin F. Isolated Ground Duplex: Hubbell #IG20CR unless indicated 15635 Alton Parkway,Suite 100, Irvine,CA 92618
<br /> g otherwise.
<br /> A. Dry and Damp Locations: Galvanized NEMA OS 1 stamped steel indicated otherwise or otherwise required. F. Accessories: multiwire branch circuits. P:949.553.1117 F:949.474.7056
<br /> box rated for the weight of the equipment supported and sized B. Contacts: 1. Cable: Wattsto er MRJ in len the re uired unless b. Provide S uare D HL01 handle clam s for circuit G. Surge Protection Receptacles: Hubbell #+iBL5362SA unless
<br /> er NFPA 70 re uirements for the devices and conductors 1. Provide with uantit of normall o en and normall PP #L 9 q q # P indicated otherwise.
<br /> p q ( ) q Y Y P Y indicated otherwise; plenum rated when not installed in breakers denoted as HLO and for all fire H. Clock Hanger Receptacles: Hubbell #HBL5235 unless indicated ARCHITECT STAMP
<br /> installed within. closed contacts as required and a minimum of two spare conduit. protection and fire alarm equipment and all ��
<br /> otherwise.
<br /> B. Wet Locations: Galvanized cast metal NEMA FB 1 Type FD box poles. 2. Wireless Configuration Tool: Wattstopper #LMCT-100 circuits serving emergency lighting. �
<br /> with asketed cover and threaded hubs and sized er NFPA 70 a. Provide multi le contactors connected in arallel I. Other NEMA Configurations: As required by the load served. v_ '�
<br /> 9 P P P unless indicated otherwise. C. Provide S uare D QO*PAF fixed handle adlock Q' G
<br /> re uirements for the devices and conductors installed with one another when the number of contacts q # P „ 2.02 FACELESS GFCI: Hubbell #GFBFST20; color as selected by Architect. Q. J
<br /> q ( ) 2.10 EMERGENCY LIGHTING CONTROLS attachment for circuit breakers denoted as HPL 2.03 MULTI-OUTLET ASSEMBLY: Wiremold Plugmold 2000 Series with Q•��
<br /> within. required exceeds the maximum capability of a A. Projects with Generators or Inverters which are Owned by the and for appliances without a local disconnecting receptacles at 6 inches on center unless indicated otherwise. Q.���
<br /> 2.03 PULL AND LARGE JUNCTION BOXES single contactor. Project Owner: means. Q►
<br /> A. Dr and Dam Locations: Galvanized NEMA OS 1 Stam ed steel 2. Coordinate contact rutin to match branch circuit Provide all fittings required for a complete installation. O
<br /> Y p p 9 1. Provide Hubbell Control Solutions #ALCR1277 or equal UL d. Provide shunt trip were denoted as "ST" or Coordinate device and channel finish color with the Architect. �� G
<br /> box sized per NFPA 70 requirements for the conductors overcurrent protection, considering derating for 924 Listed automatic load control relays as required for otherwise required. 2.04 WALL SWITCHES �v�QQ`
<br /> installed within. continuous loads, but no less than 30 amps. each control zone to accomplish the following sequence: 3. Amp Interrupting Capacity (AIC) Rating: No less than A. All Switches:
<br /> B. Wet Locations: Galvanized NEMA 250 Type 4 cast iron or cast C. Coil: Coordinate with the voltage of the control circuit. a. Bypass all ON/OFF controls associated with the the available fault current; fully rated or manufacturer
<br /> aluminum box with ground flange, neoprene gasket, and acturer s standard enclosure suitable for the control zone, including all switches, relays, and tested series combination. The Contractor shall 1.
<br /> D. Enclosure: ManufColor as selected by Architect. Q�O
<br /> stainless steel cover screws and sized er NFPA 70 environment in which the contactor is installed. 2. Horsepower rated when used as motor disconnecting means.
<br /> P contactors. determine the available fault current where not 11-19-21
<br /> requirements for the conductors installed within. 2.02 RELAYS b. Brin all emer enc luminaires to 100 ercent indicated on the Drawin s. B. Single Pole Toggle: Hubbell #1221 unless indicated otherwise.
<br /> 2.04 FLOOR BOXES A. Description: S uare D Class 8501 T e C unless indicated g g Y P g C. Three-Way Toggle: Hubbell #1223 unless indicated otherwise.
<br /> P q YP light output. 4. Do not use multi-pole circuit breakers that mount in a D. Four-Way Toggle: Hubbell #1224 unless indicated otherwise.
<br /> A. All Floor Boxes: Nonmetallic floor boxes are permitted. All otherwise or otherwise required. 2. Where phase control dimming is used, provide a separate 1-pole circuit breaker space (i .e. half-size circuit E. Single Pole Toggle with Pilot Light: Hubbell #HBL1221PLC
<br /> metal floor boxes located in slabs on grade shall be cast B. Contacts: Form C contacts rated at 30 amperes unless phase control dimmers) for normal and emergency breakers). unless indicated otherwise.
<br /> metal . Metal floor boxes installed in elevated slabs are indicated otherwise. lighting. PART 3 EXECUTION F. Single Pole Keyed: Hubbell #HBL1221L unless indicated
<br /> permitted to be stamped steel . C. Coil: Coordinate with the voltage of the control circuit. 3. Where 0-10 volt dimming is not used, the load control 3.01 INSTALLATION
<br /> B. Indoor Flush Floor Boxes for Concrete Floors: D. Enclosure: Manufacturer s standard enclosure suitable for the relay is permitted to be a Wattstopper #ELCU-200 or A. Install panelboards 6 feet to top of panelboard but no less otherwise.
<br /> 1. Nonmetallic: Wiremold Modulink 88OMP2 Series unless environment in which the relay is installed. equal . than 4 inches above floor. G. Three-Way Keyed: Hubbell #HBL1223L unless indicated
<br /> indicated otherwise with number of an s as re uired forotherwise.
<br /> g g q PART 3 EXECUTION B. Provide 4 inch thick concrete housekeeping pad for H. Four-Way Keyed: Hubbell #IiBL1224L unless indicated otherwise.
<br /> the devices installed within. PART 3 EXECUTION surface-mounted panelboards installed within 4 inches of the
<br /> 2. Metal: Wiremold Omnibox Series unless indicated 3.01 INSTALLATION 3.01 GENERAL INSTALLATION REQUIREMENTS floor. 2.05 WALLBOX DIMMERS
<br /> otherwise with number of an s as re uired for the A. Install individual controls and vela s in enclosures ad'acent A. Provide all control wiring and communications cabling, whether A. All Wallbox Dimmers: Color as selected by Architect_
<br /> 9 9 q Y J C. Provide filler plates for unused spaces in panelboards. B. Incandescent Dimmers:
<br /> devices installed within. to anelboard servin controlled circuits and make electrical or not shown on the Drawings, per manufacturer s
<br /> P 9 1.
<br /> D. Provide typed circuit directory and nameplate for each U to 600 Watts: Lutron Maestro A-600 unless
<br /> C. Indoor Flush Floor Boxes for Wood Floors: wirin interconnections. recommendations and as required for a complete and operational P #M
<br /> 9 panelboard. Revise directory to reflect circuiting changes indicated otherwise.
<br /> 1. Nonmetallic: Wiremold WMFB Series unless indicated B. Provide all relays, contactors, interposing relays, and system. required to balance phase loads.
<br /> 9 9 q q Y E. Provide five 1 inch spare conduits out of each flush-mounted 2. Between 600 and 1000 Watts: Lutron Maestro A-1000
<br /> otherwise with number of an s as re uired for the controls that are re uired but ma not be shown to switch the B. Program the entire system as established in meeting with the #M �r L
<br /> devices installed within. loads in the manner indicated on the Drawin s. Owner. unless indicated otherwise.
<br /> 9 panelboard to an accessible location above ceiling. Identify 3. Between 1000 and 1920 Watts: Lutron Maestro MAF-6AM O ❑
<br /> 2. Metal: Wiremold 880W Series unless indicated otherwise C. Provide nameplate for contactors indicating contactor number. 3.02 INSTALLATION OF TIMECLOCKS each as SPARE. #
<br /> with number of an s as re uired for the devices F.A
<br /> END OF SECTION A. Install timeclocks adjacent to panelboard serving controlled with Lutron #PHPM-WBX-120-WH power interface unless }+
<br /> 9 9 q Measure steady state load currents at each panelboard feeder indicated otherwise.
<br /> installed within. circuits and make electrical wiring interconnections. and rearrange circuits as required to balance the phase loads O
<br /> D. Indoor Recessed Floor Boxes: Wiremold RFB Series unless SECTION 260923 - LIGHTING CONTROL DEVICES B. Provide all relays, contactors, interposing relays, and C. Fluorescent 2-Wire Dimmers:
<br /> to within 10 percent maximum imbalance. Maintain proper
<br /> indicated otherwise with number of com artments as re uired controls that are required but may not be shown to switch the 1.
<br /> P q phasing for multiwire branch circuits. indicated otherwise. r
<br /> for the devices installed within. PART 1 GENERAL loads in the manner indicated on the Drawings. •� - N
<br /> G. Provide nameplate indicating panelboard equipment designation �
<br /> E. Exterior Floor Boxes: Wiremold Out Ground Box Series or 1.01 PREPARATION C. Provide nameplate for timeclocks indicating timeclock number. D. Fluorescent 3-Wire Dimmers:
<br /> for each panelboard. 1. 120 Volts, U to 6 Am s: Lutron Maestro MAF-6AM unless
<br /> e ual as manufactured b Combined Utilities Box S stems CUBS A. Hold meetin with the Owner rior to commencin work. 3.03 INSTALLATION OF OCCUPANCY SENSORS AND MOTION SENSORS P P # .E u
<br /> -)
<br /> q y y ( ) g P g � � SECTION indicated otherwise.
<br /> unless indicated otherwise with wiring devices indicated. 1. Review zoning and make adjustments requested by the A. Location Adjustments: Locations indicated are diagrammatic rR co O7
<br /> Owner. and only intended to indicate which rooms or areas require 2. 120 Volts, Between 6 and 16 Amps: Lutron Maestro �V
<br /> SECTION 262717 - EQUIPIrENT WIRING - -�
<br /> AF-6AM with Lutron PHPM-3F-120-WH ower interface � W
<br /> PART 3 EXECUTION 2. Determine all timeclock settings such as ON and OFF devices. Provide quantity and locations as required for #M # P C
<br /> 3.01 INSTALLATION times for each da of the week holida settin s, com lete covers a of res ective room or area based on unless indicated otherwise. W � IY
<br /> Y Y 9 P g P PART 1 GENERAL � U
<br /> A. Install in locations indicated and as required for splices, latitude and Ion etude of the ro est site for manufacturer s recommendations for installed devices. 3. 277 Volts, Up to 6 Amps: Lutron Maestro #MAF-6AM-277 2 ❑
<br /> q P 9 P J B. Install ultrasonic and dual technolo occu anc sensors a 1.01 COORDINATION WITH OTHER TRADES unless indicated otherwise. Q ❑ m
<br /> taps, wire pulling, equipment connections, and as required by astronomic features, etc. 9Y P Y A. Meet with all other trades before commencing any work and 4. 277 Volts, Between 6 and 16 Am s: Lutron Maestro Z � Q �
<br /> NFPA 70. 3. Determine all control settings such as on and off minimum of 4 feet from air supply ducts or other sources of f P
<br /> obtain and review shop drawings, product data, manufacturer s AF-6AM with Lutron PHPM-3F-DV-WH ower interface
<br /> B. Install ull boxes and unction boxes above accessible tri ers, blink warnin s, swee settin s, switch heavy air flow and as per manufacturer s recommendations, in � #M # P � H
<br /> P j 99 9 P 9 wiring diagrams, and manufacturer s instructions for equipment unless indicated otherwise. �
<br /> ceilings and in unfinished areas only. programming, etc. order to minimize false triggers. V V
<br /> C. Pro ram occu anc sensors as MANUAL-ON, AUTOMATIC-OFF unless furnished under other Sections. �
<br /> C. Install outlet boxes for all wall-mounted wirin devices at g p y E. Fluorescent 0-10 Volt Dimmers: W W r
<br /> 9 1. Determine all equipment connection locations and 1. U to 16 Amps: Lutron Maestro MAF-6AM with Lutron � � V
<br /> heights indicated in Section 262726 unless indicated PART 2 PRODUCTS indicated otherwise. P P # O r O
<br /> requirements and verify that proper power supply is RX-TVI ower interface unless indicated otherwise.
<br /> otherwise. Coordinate mounting heights and locations of 2.01 ALL LIGHTING CONTROL DEVICES D. Mask sensor lenses using the manufacturer s masking material available rior to subcontractor's orderin a ui ment. P IY- 0Y O �--0
<br /> outlets mounted above counters, benches, and backs lashes A. Provide all re uired conduit, wirin connectors, hardware, as required to prevent false triggers. P g q P F. Magnetic Low Voltage Dimmers: 1
<br /> P q 9 2. Sequence rough-in of electrical connections to f1 � � co
<br /> coordinate with installation of equipment. 1. U to 450 Watts: Lutron Maestro ALV-600 unless
<br /> prior to rough-in. components, accessories, etc. as required for a complete E. Adjust position of directional occupancy sensors and outdoor P #�
<br /> D. 3. indicated otherwise.
<br /> 2. Between 450 and 800 Watts: Lutron Maestro ALV-1000
<br /> back-to-back in walls; provide minimum 6 inches and one stud B. All sensors shall be suitable for the geometrical and 3.04 INSTALLATION OF INDOOR PHOTOSENSORS start-up of equipment. STORE #: 20685
<br /> se oration. environmental characteristics of the A
<br /> associated s ace and be A. Location Adjustments: Locations indicated are diagrammatic unless indicated otherwise.
<br /> P P B. Verify and coordinate all requirements and installation 3. Between 800 and 1920 Watts: Lutron Maestro AF-6AM
<br /> E. Locate flush boxes in masonr walls to re uire cuttin of suitable for the floor area to be covered. Provide multi le and only intended to indicate which rooms or areas requirePROJECT#: 59335-039
<br /> Y q 9 P details of all materials and equipment prior to rough-in. with Lutron PHPM-WBX-DV-WH ower interface unless
<br /> masonry unit corner only. Coordinate masonry cutting to sensors when necessary to meet the required room coverage. devices. Provide quantity and locations as required for C. Verif ro er volts e, # P
<br /> y p p g phase, and current rating of power indicated otherwise.
<br /> achieve neat opening. 2.02 INDOOR OCCUPANCY SENSORS complete coverage of respective room or area based on su I and immediate) re ort an discre ancies. ISSUE DATE: CH ECKSET
<br /> PP y y P y P G. Electronic Low Volta e Dimmers:
<br /> F. Install all wall-mounted boxes Iumb and level . A. Wall Switch: manufacturer s recommendations for installed devices. 9
<br /> P D. Respons i b i I i ty for verification of proper power Supp I y vo I tage 1. U to 600 Watts: Lutron Maestro AELV-600 un I ess DESIGN MANAGER: J.RAMOS
<br /> G. Install all ceiling-mounted boxes level and oriented parallel 1. Single-Relay: Wattstopper #DSW-301 unless indicated B. Install closed-loop photosensors to accurately measure the and an dams a resultin from incorrect connections shall rest P
<br /> with building I i nes and ceiling gr i d tees where app I i cab I e.
<br /> otherwise. y g g indicated otherwise.
<br /> . PRODUCTION DESIGNER:
<br /> H. Install all floor boxes level and oriented parallel with 2. Dual-Rela Wattsto er DSW-302 unless indicated the measured amount of direct light from natural or arcial 2. Between 600 and 1920 Watts: Lutron Maestro #MAF-6AM
<br /> P Y� PP # E. Any conf I i cts arising f rom I ask of coordination Sha I I be th i s with Lutron PHPM-WBX-DV-WH ower i nterface un I ess CHECKED BY: GRS
<br /> building lines and tile grout lines where applicable. otherwise. sources. Contractor's responsibility. indicated otherwise. P
<br /> I. Vertically align adjacent wall mounted outlet boxes for 3. Finish: As selected by the Architect. C. Install open-loop photosensors to accurately measure the level MCG PROJECT#: 21324
<br /> switches, thermostats, similar devices. B. Combination Wall Switch Dimmer: of daylight coming into the space while minimizing the H. LED Dimmers:
<br /> / PART 2 PRODUCTS 1. A I I LED Dimmers: D i mmer utilized sha I I be tested and MCG PROJ. MANAGER: J.SPENCER
<br /> J. Install concealed boxes within 6 inches from ceilin access 1. 0-10V Dimming: Wattsto er W-311 unless indicated measured amount of lighting from artificial sources.
<br /> 9 9� PP � 2.01 CORDS listed b the LED manufacturer as a com atible dimmer.
<br /> anels, air distribution diffusers, or removable recessed otherwise; finish as selected b the Architect. D. Calibrate dimming photosensors such that 100% artificial light y P MCG P ROJ. SPECIALIST:
<br /> P Y A. Description: Multi-conductor flexible cord Type SO for dry 2. 0-10 Volt Dimmers:
<br /> luminaires. C. Wall-Mounted: output is provided only when completely dark outside and the and damp locations or Type SOW in wet locations.
<br /> K. Su ort boxes Inde endentl of conduit; do not su ort boxes 1. Sensor: Wattstopper T-200 unless indicated otherwise. controlled lighting dims commensurately with the amount of a. Up to 16 Amps: Lutron Maestro #MAF-6AM with
<br /> PP P Y PP PP #D B. Conductor Quantity: As required for the load served; include
<br /> from ceilin g su pPort wires. 2. Power Pack: Wattsqpgg . LtGRX-TVI
<br /> itfliditd
<br /> Revision Schedule
<br /> L. Install knockout closures in unused box openings. otherwise. Owner. Calibration shall occur after all room finishes, C. Conductor Insulation Rating: As required for the voltage of otherwise.
<br /> M. Install cover lutes on boxes; see Section 262726 for cover 3. Finish: White. furniture, and window treatments have been installed. 3. Electronic Low Voltage Dimmers:
<br /> P the load served. a. U to 16 Amps: Lutron Maestro MAF-6AM with Rev Date By Description
<br /> late s ecifications. D. Ceiling-Mounted:Mounted: 3.05 INSTALLATION OF POWER PACKS P P #
<br /> P P 9- D. Conductor Ampacity: No less than the rating of the Lutron HPM-WBX-DV-WH ower interface unless
<br /> N. Ground and bond boxes as required by NEPA 70. 1. Sensor: Wattstopper #DT-300 unless indicated otherwise. A. Install power packs on junction box in accessible location overcurrent protection device protecting the circuit. P
<br /> END OF SECTION 2. Power Pack: Wattsindicated otherwise.
<br /> 2.02 CORD CAPS: Match cord cap to receptacle configuration at outlet 4. Ma Hetes Low Volta a Dimmers
<br /> otherwise. B. Do not switch power serving power packs. All required 9 9
<br /> provided for equipment. a. U to 16 Amps: Lutron Maestro MAF-6AM with
<br /> SECTION 260553 - IDENTIFICATION FOR ELECTRICAL SYSTEMS 3. Finish: White. switching shall occur on the load side of the power pack P P #
<br /> 2.03 OTHER MATERIALS: Provide all disconnect switches, wiring devices, Lutron HPM-WBX-DV-WH ower interface unless
<br /> E. Accessories: Provide heavy duty coated steel wire protective relay. conduit, wire and cable, and boxes required. � P
<br /> PART 1 GENERAL - NOT USED guards compatible with specified occupancy sensors where 3.06 INSTALLATION OF OUTDOOR PHOTOCELLS indicated otherwise.
<br /> subject to impact. A. Install photocell facing north with unobstructed view. PART 3 EXECUTION 2.06 ABOVE-FLOOR SERVICE FITTINGS: Hubbell #SC3098A
<br /> PART 2 PRODUCTS 2.03 OUTDOOR MOTION SENSORS B. Install such that photocell does not face artificial light 3.01 ELECTRICAL CONNECTIONS housing with plates as required for the wiring
<br /> 2.01 NAMEPLATES: En raved laminated lastic with 1 8 inch letters on A. Wall-Mounted for Switching: sources includin li ht sources controlled b the hotocell device installed within unless indicated SHEET TITLE:
<br /> 9 P / g= 9 9 Y P A. Make electrical connections in accordance with equipment otherwise. ELECTRICAL
<br /> contrasting background. 1. Sensor: Wattstopper #EW-200 unless indicated otherwise. itself. manufacturer s instructions.
<br /> 2.02 LABELS: As required by regulatory agencies. 2. Finish: As selected by the Architect. C. Weatherproof all connections. Do not install photocell with
<br /> 2.03 WIRE MARKERS: Cloth, tape, split sleeve, or tubing type. B. Wall-Mounted for 0-10 Volt Dimming: conduit stem facing up to prevent infiltration of water. SPECIFICATIONS
<br /> PART 3 EXECUTION 1. Sensor: Wattstopper #FSP-211 unless indicated D. Adjust external sliding shields under optimum lighting
<br /> 3.01 NAMEPLATES: Provide nameplates with the unique equipment otherwise. conditions to achieve desired turn-on and turn-off SCALE:AS SHOWN
<br /> designation at each electrical distribution and control equipment 2. Lens: Wattstopper #FSP-L* as required for the activation.
<br /> enclosure, communication cabinet, and control device station. application.
<br /> 3.02 WARNING LABELS: Provide a I I regu I story required and i ndustry 3. Finish: White. SHEET NUMBER:
<br /> standard warning labels on all electrical equipment, including 4. Configuration Tool: Wattstopper #FSIR-100 unless
<br /> high-voltage, tested series rated combination, and arc flash hazard indicated otherwise.
<br /> E-0002
<br /> labeling.
<br />
|