|
water piping; Cooling condensate drain piping insulation; fasteners not permitted Watts Regulator Company, AGA Z21.22 certified, bronze body, teflon seat, stainless
<br /> 3.01 INSTALLATION steel stem and springs, automatic, direct pressure actuated, temperature relief _
<br /> A. Determine that roof structure, roof insulation, and roof membrane are structurally PART 2 PRODUCTS PART 3 EXECUTION maximum 210 degrees F, capacity ASME (BPV IV) certified and labeled.
<br /> adequate to support weight of pipe, duct, conduit, and supports and hangers. 2.18 STRAINERS
<br /> B. Install supports and hangers in accordance with manufacturer's recommendations. 2.01 REQUIREMENTS FOR ALL PRODUCTS OF THIS SECTION 3.01 EXAMINATION A. Manufacturers: Armstrong International, Inc; Green Country Filtration; WEAMCO.
<br /> C. Install supports at maximum spacing of 10 feet unless closer spacing is required A. Surface Burning Characteristics: Flame spread/Smoke developed index of 25/50, A. Verify that piping configurations are correct type for piping cover component B. Size 2 inch and Under: Threaded brass body for 175 psi CWP, Y pattern with 1/32
<br /> due to weight of pipe or conduit contents or greater spacing is specifically maximum, when tested in accordance with ASTM E 84, NFPA 255, or UL 723. configurations specified. inch stainless steel perforated screen. =
<br /> allowed by manufacturer; space and adjust to support an equal amount of weight; do B. The Contractor may use any of the following insulating/jacketing materials, at his 3.02 INSTALLATION 2. Class 150, threaded bronze body 300 psi CWP, Y pattern with 1/32 inch
<br /> not exceed manufacturer's recommended load limits. option, provided the selected material meets with the approval of all State, local A. Install products of this section in accordance with manufacturer's printed stainless steel perforated screen.
<br /> D. Remove roofing aggregate from area 2 inches larger than support base; comply with authorities and utility company requirements. Verification of compliance of the installation instructions. C. Size 1-1/2 inch to 4 inch: Class 125, flanged iron body, Y pattern with 1/16 inch
<br /> roofing manufacturer's requirements to maintain roofing warranty. selected insulating/jacketing material is the sole responsibility of the installing 3.03 PROTECTION OF INSTALLED PRODUCTS stainless steel perforated screen.
<br /> E. Install an additional sheet of roofing material, support pad, or deck plate beneath Contractor. A. Do not allow damage to installed products by subsequent construction activities; D. Size 5 inch and Larger: Class 125, flanged iron body, basket pattern with 1/8 inch
<br /> each support base. 2.02 GLASS FIBER protect products until Substantial Completion. Replace any damaged products prior stainless steel perforated screen.
<br /> F. Support Pads: Remove rock, aggregate, dirt and excess dust from area to be covered A. Manufacturers: Knauf Insulation; Johns Manville Corporation; Owens Corning Corp; to occupancy.
<br /> by pad; Apply support pad on cleaned area; Center bases on top of support pads. CertainTeed Corporation. PART 3 EXECUTION
<br /> G. Deck Plates: Required for loads greater than 100 pounds per support; Locate B. Insulation: ASTM C 547 and ASTM C 795; rigid molded, noncombustible; 'K' value: END OF SECTION
<br /> centered under bases of pipe supports and hangers; Remove rock, aggregate, dirt and ASTM C 177, 0.24 at 75 degrees F; Maximum service temperature: 850 degrees F; 3.01 EXAMINATION
<br /> excess dust from an area 2 inches larger than deck plate; Install with curved edges Maximum moisture absorption: 0.2 percent by volume. SECTION 221005 — PLUMBING PIPING A. Verify that excavations are to required grade, dry, and not over—excavated. I 0 2020 STARBUCKS COFFEE COMPANY
<br /> up. C. Insulation: ASTM C 547 and ASTM C 795; semi—rigid, noncombustible, end grain 3.02 PREPARATION "KS -
<br /> O
<br /> H. Pipe Supports: Center beneath pipe so that pipe is located squarely over and adhered to jacket; 'K' value: ASTM C 177, 0.24 at 75 degrees F; Maximum service PART 1 GENERAL A. Ream pipe and tube ends. Remove burrs. Bevel plain end ferrous pipe. S I ARBUC R
<br /> through cradle or hanger. Set pipe in support without dropping or causing undue temperature: 650 degrees F; Maximum moisture absorption: 0.2 percent by volume. B. Remove scale and dirt, on inside and outside, before assembly.
<br /> impact. D. Vapor Barrier Jacket: White kraft paper with glass fiber yarn, bonded to 1.01 SECTION INCLUDES C. Prepare piping connections to equipment with flanges or unions. 2401 UTAH AVENUE SOUTH
<br /> I. All roofing penetrations shall be flashed and weather sealed by the roofing aluminized film; moisture vapor transmission when tested in accordance with ASTM E A. Pipe, pipe fittings, valves, and connections for piping systems: Sanitary sewer, 3.03 INSTALLATION
<br /> manufacturer's authorized roofing contractor at this Contractor's expense. This 96/E 96M of 0.02 perm—inches. interior; Sanitary sewer, exterior; Domestic water, interior; Domestic and fire A. Install in accordance with manufacturer's instructions. SEATTLE, WASHINGTON 98134
<br /> Contractor shall contract with the factory authorized roofing contractor for the E. Vapor Barrier Lap Adhesive: Compatible with insulation. service water, exterior; Natural gas, interior. B. Provide non—conducting dielectric connections wherever jointing dissimilar metals. 206 318-1575
<br /> specific roofing system applicable to this project. The use of an unauthorized F. Insulating Cement/Mastic: ASTM C 195; hydraulic setting on mineral wool. C. Route piping in orderly manner and maintain gradient. Route parallel and
<br /> roofing contractor may result in removal and replacement of the penetration systems G. Fibrous Glass Fabric: Cloth: Untreated; 9 oz/sq yd weight; Blanket: 1.0 Ib/cu ft PART 2 PRODUCTS perpendicular to walls.
<br /> at this Contractor's expense. density, Weave: 5x5. D. Install piping to maintain headroom, conserve space, and not interfere with use of THESE DRAWINGS AND THE PROJECT MANUAL
<br /> 3.02 FIELD QUALITY CONTROL H. Indoor Vapor Barrier Finish: Vinyl emulsion type acrylic, compatible with 2.01 The Contractor may use any of the following piping materials, at his option, provided the space. ARE CONFIDENTIAL AND SHALL REMAIN THE
<br /> A. After system startup, correct any deficiencies that arise, including but not insulation, white color; Outdoor Vapor Barrier Mastic: Vinyl emulsion type acrylic selected material meets with the approval of all State and local authorities and utility E. Group piping whenever practical at common elevations. SOLE PROPERTY OF STARBUCKS
<br /> limited to, improper location or position, improper seating or level on the roof, or mastic, compatible with insulation, black color; Outdoor Breather Mastic: Vinyl company requirements. Verification of compliance of the selected piping material with F. Install piping to allow for expansion and contraction without stressing pipe,
<br /> lack of roof pads or deck plates, inadequate operation, and as directed by emulsion type acrylic or mastic, compatible with insulation, black color. local requirements is the sole responsibility of the installing Contractor. Verify the joints, or connected equipment. CORPORATION,WHICH IS THE OWNER OF THE
<br /> Engineer. K. Insulating Cement: ASTM C 449/C 449M. use of plastic piping systems with the local jurisdiction. Non—metallic piping systems G. Provide clearance in hangers and from structure and other equipment for COPYRIGHT IN THIS WORK. THEY SHALL NOT BE
<br /> 2.03 FLEXIBLE ELASTOMERIC CELLULAR INSULATION may not be used in any return air plenum ceiling spaces. No exceptions. installation of insulation and access to valves and fittings. REPRODUCED(IN WHOLE OR IN PART), SHARED
<br /> END OF SECTION A. Manufacturer: Armacell International; 2.02 SANITARY SEWER PIPING, BURIED BEYOND 5 FEET OF BUILDING H. Locate all valves and control elements in accessible areas wherever possible to WITH THIRD PARTIES OR USED IN ANY MANNER
<br /> B. Insulation: Preformed flexible elastomeric cellular rubber insulation complying A. Cast Iron Pipe: ASTM A 74 service weight; Fittings: Cast iron; Joint Seals: ASTM avoid access doors. Provide access where valves and fittings are not exposed or ON OTHER PROJECTS OR EXTENSIONS TO THIS
<br /> SECTION 220548 VIBRATION AND SEISMIC CONTROLS FOR PLUMBING PIPING AND EQUIPMENT with ASTM C 534 Grade 1; use molded tubular material wherever possible; Minimum C 564 neoprene gaskets, or lead and oakum. located in accessible areas. Provide ceiling access doors for access to all valves PROJECT WITHOUT THE PRIOR WRITTEN
<br /> Service Temperature: —40 degrees F; Maximum Service Temperature: 220 degrees F; B. Vitrified Clay Pipe: ASTM C 700, Standard Strength; Fittings: Clay; Joints: and control elements located above inaccessible ceiling areas. Provide minimum 12
<br /> PART 1 GENERAL Connection: Waterproof vapor barrier adhesive. Bell—and—spigot, with ASTM C 425 compression joint device. x 12 inch size for hand access, 18 x 18 inch size for shoulder access, and as CONSENT OF STARBUCKS CORPORATION.
<br /> C. Elastomeric Foam Adhesive: Air dried, contact adhesive, compatible with C. ABS Pipe: ASTM D 2751, ASTM F 628, ASTM D2661, or ASTM D2751; Fittings: ABS; indicated. Provide 4 x 4 inch for shut off valves only. Provide rated access doors THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> 1.01 SECTION INCLUDES insulation. Joints: Solvent welded with ASTM D 2235 cement. where installed in fire rated construction. Review locations prior to INTENDED TO EXPRESS DESIGN INTENT FORA
<br /> A. Concrete housekeeping pads; Vibration isolators; Seismic restraints. 2.04 JACKETS 2.03 SANITARY SEWER PIPING, BURIED WITHIN 5 FEET OF BUILDING fabrication. PROTOTYPICAL STARBUCKS STORE(WHICH IS
<br /> A. PVC Plastic. A. Cast Iron Pipe: ASTM A 74 service weight; Fittings: Cast iron; Joints: I. Establish elevations of buried piping outside the building to ensure not less than
<br /> PART 2 PRODUCTS 1. Manufacturers: Knauf Fiber Glass; Johns Manville Corporation; Owens Corning Hub—and—spigot, CISPI HSN compression type with ASTM C 564 neoprene gaskets or lead the maximum local frost depth cover. Install tracer wire on all plastic piping SUBJECT TO CHANGE AT ANYTIME)AND DO NOT
<br /> Corp; CertainTeed Corporation. and oakum. outside the building. REFLECT ACTUAL SITE CONDITIONS. NEITHER
<br /> 2.01 MANUFACTURERS 2. Jacket: One piece molded type fitting covers and sheet material, off—white B. ABS Pipe: ASTM D 2751, ASTM F 628, ASTM D2661, or ASTM D2751; Fittings: ABS; J. Install vent piping penetrating roofed areas to maintain integrity of roof PARTY SHALL HAVE ANY OBLIGATION NOR
<br /> A. Isolation Technology, Inc.; Kinetics Noise Control, Inc.; Mason Industries. color; Minimum Service Temperature: 0 degrees F; Maximum Service Joints: Solvent welded with ASTM D 2235 cement. assembly. LIABILITY TO THE OTHER(EXCEPT STATED
<br /> 2.02 BASES Temperature: 150 degrees F; Moisture Vapor Permeability. 0.002 perm inch, 2.04 SANITARY SEWER PIPING, ABOVE GRADE K. All roofing penetrations shall be flashed and weather sealed by the roofing ABOVE) UNTIL A WRITTEN AGREEMENT IS FULLY
<br /> A. Concrete Housekeeping Pad: Construction: Concrete as specified for flooring; maximum, when tested in accordance with ASTM E 96/E 96M; Thickness: 10 mil; A. Cast Iron Pipe: ASTM A 74, service weight; Fittings: Cast iron; Joint Seals: manufacturer's authorized roofing contractor at this Contractor's expense. This
<br /> Design: 4 high above the surrounding finished flooring and 4 greater in dimension Connections: Brush on welding adhesive; Covering Adhesive Mastic: ASTM C 564 neoprene gaskets, or lead and oakum. Contractor shall contract with the factory authorized roofing contractor for the I EXECUTED BY BOTH PARTIES.
<br /> that the equipment supported, or greater if detailed on the Drawings or when Compatible with insulation. B. Cast Iron Pipe: CISPI 301, hubless, service weight; Fittings: Cast iron; Joints: specific roofing system applicable to this Project. The use of an unauthorized
<br /> indicated. B. ABS Plastic: CISPI 310, neoprene gaskets and stainless steel clamp—and—shield assemblies. roofing contractormay result in removal and replacement of the penetration systems STARBUCKS TEMPLATE VERSION: 12020-01-31.1
<br /> 2.03 VIBRATION ISOLATORS 1. Jacket: One piece molded type fitting covers and sheet material, off—white 2.05 WATER PIPING, BURIED BEYOND 5 FEET OF BUILDING at this Contractor's expense.
<br /> A. Restrained Open Spring Isolators: Springs: Minimum horizontal stiffness equal to color; Minimum Service Temperature: —40 degrees F; Maximum Service A. Ductile Iron Pipe: AWWA C151/A21.51; Fittings: AWWA C110, ductile or gray iron, L. All sanitary vent system terminations shall be a minimum of ten feet from any fresh
<br /> 75 percent vertical stiffness, with working deflection between 0.3 and 0.6 of Temperature of 180 degrees F; Moisture Vapor Permeability. 0.012 perm inch, standard thickness; Joints: AWWA C111/A21.11, rubber gasket with 3/4 inch diameter air intake and twenty—five feet on medical facilities (hospitals, clinics, etc.) ARCHITECT OF RECORD
<br /> maximum deflection. Color code springs for load carrying capacity, Spring Mounts: when tested in accordance with ASTM E 96/E 96M; Thickness: 30 mil.; rods. M. Where pipe support members are welded to structural building framing, scrape, brush o0 ;
<br />
|