|
GENERAL PLUMBING NOTES PIPING INSULATION VALVES
<br /> Scope Soil,Waste,and Vent Piping Water Piping General
<br /> p
<br /> The intent of the Specifications and the Drawings is to provide a complete and fully operational Soil,Waste and Vent piping 10"and smaller shall be service weight, hubless,cast iron pipe, Provide thermal insulation on all hot and cold water,and horizontal waste piping in ceiling Plumbing Contractor to provide valves where indicated on plans and as necessary for
<br /> plumbingstem. The Contractor shall furnish all labor,material,and equipment related to the and fittings with neoprene gasket and stainless shield and clamp.provide hub and spigot, spaces,and on all cold water piping in casework and bar areas. Use self sealing closed cell proper system operation and component isolation. Install valves for each fixture and item
<br /> system. foam or jacketed fiberglass insulation with manufacturer approved adhesives,sealers,and of equipment. Provide braided stainless steel hose unless otherwise noted between
<br /> installation of the plumbing work. servive weight cast iron soil pipe and fittings below grade where required by local codes. 1 g PP ( )
<br /> Schedule 40 ABS and PVC pipe and fittings with solvent weld may be substituted for soil,waste, coatings. All materials used shall not exceed 25 for flame spread,50 for fuel contributed,or 50 valve and equipment in accordance with manufacturer's specifications. Locate shut-off
<br /> Site Examination and vent piping above and below grade if allowed by local authority.All horizontal runs shall for smoke developed. Unless otherwise required by the local authority or energy codes,the valves adjacent to equipment for easy access such that valves can be reached without
<br /> The Contractor shall thoroughly examine all areas where fixtures,equipment,and piping will be drain at a grade of 1/4"per foot where possible but in no case less than 118"per foot. minimum insulation levels shall be as follows" moving equipment. Shut off valves to be ball type.
<br /> Coordinate with local authorities for drainage requirements for equipment designated with Pipe Size(diameter) Insulation Thickness
<br /> installed and will report any condition that,in his opinion,prevents the proper installation of the indirect waste to floor drains.provide piped drain to sanitary if required b local jurisdiction. �� ll Valves CO 2020 STARBUCKS COFFEE COMPANY
<br /> plumbing work. P P P ry q Y Less than or equal to 1 1/2 1
<br /> 2"or greater 11/211 Provide valves for working pressure in water piping of 125 PSI or greater. Unless noted S I ARBUCKSQ
<br /> Domestic Water and Piping otherwise valves shall be as follows:
<br /> Standards Domestic water piping 2112"and smaller shall be copper tube with wrought copper sweat (Insulation Value=k value not exceeding 0.027 BTU per inch/h*ft2*f) 2401 UTAH AVENUE SOUTH
<br /> Equipment and materials shall conform with theappropriate rovisions of CSA ULC ASME Valve Type Manufacturer Model No.
<br /> P fittings joined with non-lead,non-antimony solder. Profive type"L"copper tube above grade Safety Covers Check Valve(up to 2") Nibco #S-22 SEATTLE, WASHINGTON 98134
<br /> ASTM, UL, NEMA,ASHRAE, NFPA,as applicable to each individual unit or assembly. and type"K"below grade. 206 318-1575
<br /> Install specified no scald safety covers with insulated foam liner and tamper proof strap as Full Port Ball Valve(up to 3 ) Nibco #S-FP-600
<br /> Codes furnished by Starbucks at all exposed piping. Gate Valve(up to 3") Nibco #S-113
<br /> Condensate Drainage Piping THESE DRAWINGS AND THE PROJECT MANUAL
<br /> All work shall be performed in strict accordance with all applicable provincial and local codes The Plumbing Contractor shall provide condensate drains for air handling units and Starbucks Ice Bin Drain Temperature and Pressure Relief Valve Wilkins #TP1100A ARE CONFIDENTIAL AND SHALL REMAIN THE
<br /> SOLE PROPERTY OF STARBUCKS
<br /> and ordinances. In case of conflict between the drawings and specifications and the codes and equipment(refer to schedule).Condensate drainage piping shall be type"M"copper tubing with Insulate ice bin copper drain lines with 1/2"thick,self sealing,sectional,closed cell foam. Water Hammer Arrestor Wilkins #Backflow Preventer(whole-house) Wilkins #1250 1250 CORPORATION,WHICH IS THE OWNER OF THE
<br /> ordinances,the highest standard shall apply. The contractor shall satisfy code requirements as wrought copper sweat fittings joined with 50150 solder. COPYRIGHT IN THIS WORK. THEY SHALL NOT BE
<br /> a minimum standard without an extra cost to Starbucks. Backflow Preventer(single device) Wilkins #700
<br /> Y HVAC Piping REPRODUCED(IN WHOLE OR IN PART), SHARED
<br /> Natural Gas Piping Vacuum Relief Valve Wilkins #35VCH
<br /> p g Insulate refrigerant suction piping and cooling coil condensate piping with 3/4"thick,self
<br /> Pressure Reducing Valve Wilkins #500YSBR WITH THIRD PARTIES OR USED IN ANY MANNER
<br /> Warranty Gas Piping shall be Schedule 40,seamless, black steel pipe.Provide piping support blocking sealing,closed cell foam. Insulate HVAC hot and chilled water piping systems and low pressure ON OTHER PROJECTS OR EXTENSIONS TO THIS
<br /> The Contractor shall unconditionally warrant all work to be free of defects in material and on roof,compatible with roofing system. steam and condensate piping with 11/2"thick,heavy duty,self sealing,jacketed fiberglass. Trap Seal Primer J. R.Smith #2699-1 PROJECT WITHOUT THE PRIOR WRITTEN
<br /> workmanship for a period of one year from the date of final acceptance by Starbucks and will CONSENT OF STARBUCKS CORPORATION.
<br /> repair or replace any defective work promptly and without charge and restore any other existing Hangers and Supports Rain Conductors Supply THESE DRAWINGS AND SPECIFICATIONS ARE
<br /> work damaged in the course of repairing defective materials and workmanship. The Plumbing Contractor shall furnish all pipe supports required forequipment and material.All Insulate rain water conductors which ass through occupied areas with 112"thick fiberglass. If water pressure supplied to store is greater than 65 PSI,then provide a rssure regulator INTENDED TO EXPRESS DESIGN INTENT FOR A
<br /> 9 P 9 P g P P PP qP 9 P 9 P PP g P p g
<br /> horizontal runs of piping shall be supported by pipe hangers installed as required by local to main supply to maintain water pressure. Provide backflow prevention on water service PROTOTYPICAL STARBUCKS STORE(WHICH ISSUBJECT TO CHANGE AT ANYTIME)AND DO NOT
<br /> codes,additional supports shall be provided where required to prevent sagging. Hangers and if required by local codes. REFLECT ACTUAL SITE CONDITIONS. NEITHER
<br /> pipe attachments to be factory fabricated with galvanized coatings;non-metallic coated for PARTY SHALL HAVE ANY OBLIGATION NOR
<br /> hangers in direct contact with copper tubing. LIABILITY TO THE OTHER(EXCEPT STATED
<br /> ABOVE) UNTIL A WRITTEN AGREEMENT IS FULLY
<br /> Connections EXECUTED BY BOTH PARTIES.
<br /> Install unions adjacent to each valve and at final connection to each piece of equipment. Install STARBUCKS TEMPLATE VERSION: i2020-01-31.1
<br /> dielectric couplings to connect piping materials of dissimilar metals. Screw joint steel piping up
<br /> to and including 1 1/2".Weld piping use non-lead,non-antimony solder for soldering domestic ARCHITECT OF RECORD
<br /> water copper pipe. o
<br /> M B
<br /> Cleanouts S Y
<br /> cc—
<br /> Provide J.R.Smith or equivalent floor and wall cleanouts as indicated on the drawings or where P L U M B I N G
<br /> required by code in all soil,waste,and drain lines. In areas with ceramic tile or carpeted SYMBOL DESCRIPTION SYMBOL DESCRIPTION
<br /> flooring,provide cleanouts with square,adjustable,nickel bronze top with tile recess. Cleanouts SANITARY DRAIN ABOVEGROUND —C—UO CLEAN OUT
<br /> shall be same size as pipe except that cleanouts larger than 4"will not be required. Where - — — - SANITARY DRAIN BELOWGROUND G� GRADE CLEAN OUT
<br /> cleanouts occur in walls of finished areas,they shall be concealed behind chrome placed -GW- GREASE WASTE ABOVEGROUND wc❑ WALL CLEAN OUT 4mcagPitecure
<br /> access covers. - -Gw- - GREASE WASTE BEL❑WGROUND N.I.C. NOT IN CONTRACT 15635 Alton Parkway,Suite 100, Irvine,CA 92618
<br /> —AW— ACID WASTE ABOVEGROUND VTR VENT THROUGH ROOF P:949.553.1117 F:949.474.7056
<br /> Installation - -AW- - ACID WASTE BELOWGR❑UND BALL VALVE ARCHITECT STAMP
<br /> Install exposed piping free of sags and bends. Provide bracket standoffs from mounting — — VENT LINE CHECK VALVE ♦� Q
<br /> surfaces to allow 1"of cleaning space all around piping,including any added piping insulation. -AV-— ACID VENT
<br /> � PRESSURE REGULATING VALVE (PRV) Q`Q►�G�
<br /> Install fittings for changes in direction and branch connections. Install sleeves for pipes passing —WAGD— WASTE ANESTHESIA GAS DISP❑SAL VVJJO �V
<br /> through concrete and masonry walls,gypsum board partitions,concrete floor and roof slabs. S STORM DRAIN ABOVEGROUND GAS COCK Q•�
<br /> Sealg ene
<br /> P'P I e penetrations through rated construction with fire stopping sealant lant material. -S- - STORM DRAIN BEL❑WGR❑UND p PRESSURE REGULATING VALVE (PRV)
<br /> 0S OVERFLOW STORM DRAIN AND GAS COCK
<br /> P Q
<br /> P �♦�Q
<br /> Underground water and sewer lines shall be laid in separate trenches with a minimum horizontal ♦ Q`
<br /> ��� �♦��Q
<br /> spacing as required by code,excavated to the proper depth and graded to produce the required COLD WATER (CW) MIXING VALVE HOT WATER (HW) GAS COCK
<br /> fall. ----- H❑T WATER CIRCULATING (HWC) VALVE IN RISE
<br /> 11-19-21
<br /> -140=--- HOT WATER 1400 AUTOMATIC BALANCING VALVE
<br /> Testing -140°----- HOT WATER CIRCULATING 140° mac— RUNNING TRAP
<br /> All pipes shall be tested by an approved method before they are backfilled or concealed. After -T --- TEMPERED WATER [F\HB HOSE BIBB
<br /> testing is complete,the Plumbing Contractor shall disinfect the potable water system as -T----- TEMPERED WATER CIRCULATING I--I WH WALL HYDRANT
<br /> required by local authority. Test water purity according to local requirements and submit -CS -- COLD SOFT WATER _f FH FIRE HYDRANT
<br /> certified test results to engineer for review and approval. -HS---- HOT SOFT WATER V.C.P. VITRIFIED CLAY PIPE
<br /> -HS----- HOT SOFT WATER CIRCULATING C.I. CAST IRON
<br /> F FIRE LINE I.E. INVERT ELEVATI❑N
<br /> G GAS LINE B.F.F. BELOW FINISHED FLOOR
<br /> A COMPRESSED AIR LINE PLUMBING RISER NUMBER
<br /> v VACUUM LINE
<br /> ox OXYGEN LINE DOWNSPOUT NOZZLE
<br /> D CONDENSATE LINE ORD ROOF DRAIN/OVERFLOW ROOF DRAIN }� L
<br /> 0
<br /> 0
<br /> = CF)
<br /> 'S C-q
<br /> W -C Q
<br /> Iii C: U
<br /> Q (Do 00
<br /> Z m Q C:
<br /> 0
<br /> U U
<br /> W W r V
<br /> O LO O O 0
<br /> 6- co Cn
<br /> STORE #: 20685
<br /> PROJECT#: 59335-039
<br /> ISSUE DATE: CHECKSET
<br /> DESIGN MANAGER: J.RAMOS
<br /> PRODUCTION DESIGNER:
<br /> CHECKED BY: GRS
<br /> MCG PROJECT#: 21324
<br /> MCG PROJ. MANAGER: J.SPENCER
<br /> MCG PROJ. SPECIALIST:
<br /> Revision Schedule
<br /> Rev Date By Description
<br /> SHEET TITLE:
<br /> PLUMBING
<br /> SPECIFICATIONS
<br /> SCALE:AS SHOWN
<br /> SHEET NUMBER:
<br /> P-0004
<br />
|