Laserfiche WebLink
ULIULC Listed Red Threadu 11 A Piping-System <br /> RED l-HREAD IIA PIPING <br /> RED THREAD IIA Primary Piping REO THREAD IIA Secondary Containment Piping <br /> Nom.Pipe Pipe Nom.Pipe Pipe <br /> Size Part Length Size Part Length <br /> (In./nun) Number (k.) (In.hnns) Number (k.) _ <br /> 2 56 01102 :069-1 15 >,( 3 (10 D11030.060.4 16 <br /> 2 50 011020-069-2 22.25 3 00 011030.069.5 22-25 <br /> 2 50 011020.0593 26-30 3 00 011030-069-6 26-30 i <br /> 3 80 011030-069-1 15 4 100 011040-077-5 15 <br /> 3 80 011030-069-2 22-25 4 160 011040-069-5 22.25 <br /> 3 80 011030.069-3 26-30 4 100 011040-077-6 26.30 <br /> 4 100 011040-071-1 15 6 150 011060.120.5 15 <br /> 4 100 011040-069-2 22-25 6 150 011060.120-0 22.25 <br /> 4 100 011040-071-3 26.30 6 150 011060-120-6 26-30 <br /> DIMENSIONAL DATA <br /> Nominal Nominal MITI <br /> Pipe Nominal Nominal Wall Nominal Pressure/ Test External Pressure <br /> size I.D. O.D. Thickness Weight I Temperature Pressure Max.Rating(psig/Ml'a) <br /> (in.lmm) (InJmm) (In.hmn) (In./corn) (OsNUkgm) Max.Rating (pslg/MPa) 756F/241C 160"F166'C <br /> 2 2.235 2.375 .070 0.5 250 pi(01150"F 375 65 80 <br /> 50 57 61 1.76 0.74 1.72 MPa @ 661C 2.59 57 .55 <br /> 3 3.380 3.500 .070 0.7 175 prig @1450"F 300 36 34 <br /> 80 85 $10 2.54 1.04 1.21 MPa 0p 66'C 2.07 .2.5 .23 <br /> 4 4.360 4.560 .085 1.2 125 psig®150T 265 34 30 <br /> 100 111 'I1G 2.'1(1 1.79 0.86 MPa(e),611"C 1.01 .23 .21 <br /> 6 BAD$ 6.678 .135 2.4 NA 265 22 20 - <br /> 15D 163 170 3.43 3.61 NA 1.81 .15 .14 <br /> TYPICAL PHYSICAL PROPERTIES(') <br /> PROPERTY RED THREAD`IIA PieBantling Radius,Minimum <br /> psi @75"r MPa@24'C psl@750"F Mine 66"C Pipe Size 2" 3" 4' 61 - <br /> a Tensie ST 2105) Inches <br /> Ultimate Stress 10300 71.0 8,200 56.5 i <br /> Design Stress 2,975 17.8 2,050 14.1 Ft. 75 110 140 204 <br /> Modulus of Eleslcily 1.82 x 101 12540 1.42 x 1D` 9791 <br /> Axial Compression(ASTM D695) 33,300 230.0 25,600 177.0 In 21.3 33.5 42.7 62.2 <br /> Ultimate Stress 6,300 57.2 6,400 44.1 <br /> Design Siress 1.26 x 10 -0607 .89 x IT 8136 <br /> Modulus of Elasticity <br /> (1)All vetoes exceplpressuredemparausre <br /> Beam Bending(SFPTM) maximum rating are aminal values.Tolerances or <br /> Ultimate Stress 23,000 159.0 18,200 13'J.0 maximumiminimum limits can be obtained from Smith <br /> Design Slressm 2,900 20.0 2,40016.5 Fl6ercasl. <br /> Modulus of Elasticity Ziax 10, 15031 1.70x10' 11721 (2)All sizes Mn accept full vaGmm preaswes at '.. <br /> (Long Term par ASTM D2925) mtximum temperature ratings. <br /> (3)Ultimate and alterable design stresses are <br /> Hydrostatic Burst(ASTM D7599) - based on junimum reinforced gal thleMoss.Pipe is <br /> Ultimate Hoop 30.000 234 39,200 271 manufactured In complianw wlth ASTM 02900. <br /> Tensile Stress (4) Design bending stress is 110 ofuigmale to <br /> account for comhmed setae(i.e.bending and <br /> Hydrostatic Design(ASTM D2992) 2'-3" 21G 31 213' 2.83- pressure) <br /> Procedure 9,4101'% 64.11a" 7,400" 5'1'- (5) Design elness is basad an long term cyclic(argue <br /> Cyclic 160x IT 4'-6" 4'-6' 4"-6" 4"•6- data using ASTM 02092 lost method.Hwave6 all <br /> Cycles 13,04010 11101 10,460 72.1 testing is not complete at Uma of fining. <br /> (6) For RED THREAD IIA pipe Ore hydrostatic <br /> Coelbolant of Linear 0.88 x 101 in.AnPF cyclic design slrenswes dmennlned at 150'end I <br /> Thermal Expansion(SFPTM) 158 is 101m7n7mmPC 200'F,per ASTM D2992 Procedure A.Based on lh6 i <br /> dole,lire extrapolated value at 15'F Is 13,030 psi. <br /> Specific Gravity 1.8 (7)For RED THREAD IIA pipe the hydmstellestela <br /> _ Flow Felt-r 150 design start was dotomdnad$175•and 200•F,pm <br /> Hazim-Wllllams Cooklcienl A67M D2992 Procedure A.Based on this data,do <br /> exeapoload value at 160T is 7,400 pd. <br /> 4 <br />