Laserfiche WebLink
2x4 P.T. WD. SLEEPER W/ 3/16" X 3" POWDER DRIVEN FASTNER @ 24" O.C.2x D.F.P.T. WD. SLEEPER W/ #10 X 2 3/4" F.H. SCREWS @ 12" O.C.BASE - REFER TO FINISH SCHEDULECAB. FRAMEPLAM FACED CAB. DOORF.F.4"CONC. MAT SLAB -S.S.D.AD.029FAUCET - S.P.D.3/4" CLEATS - TYP.1/4" PLYWD. BACKWD. STUD PARTITION -REFER TO FLOOR PLAN FOR SIZEFLOOR FIN. TO TERMINATE @ BASE OF WALL UNDER CAB.COUNTERTOP - REFER TO CASEWORK SCHEDULE4"CAB. FRAME - TYP.2'-0"WALL BASE - REFER TO FINISH SCHEDULE2'-5"F.F.AD.027WIRE PULLS - TYP.PLAM FINISH AT ALL EXPOSED SURFACES - REFER TO CASEWORK SCHEDULENOTE:ANCHORAGE PER WIC # OPA-2649-102x D.F.P.T. BASE W/ #12 X 3 1/2" L WD. SCREWS1/4" DIA. X 3" L. SHT. MTL. SCREWS @ 6" O.C. - (USE S.S. FINISH WASHERS & SCREWS W/ VINYL COLORED PLUGS AT OPEN SHELVING)F.F.CONC. SLAB - S.S.D.1/2" MIN. X3" SOLID WD. CLEAT -CONT.WALL BASE -REFER TO FINISH SCHEDULE2X STUD PARTITION - REFER TO FLOOR PLAN FOR SIZEBATT INSULATION - REFER TO WALL TYPE SCHED. FOR R-VALUE3X WD. BACKING PLATE - SEE DETAIL /15AD.02NOTE:ANCHORAGE PER WIC # OPA-2649-10F.F.WALL BASE -REFER TO FINISH SCHEDULE1/4" DIA. X 3" L. SHT. MTL. SCREWS @ 6" O.C. -(USE S.S. FINISH WASHERS & SCREWS W/ VINYL COLORED PLUGS AT OPEN SHELVING)CONC. SLAB - S.S.D.1/2" MIN. X 3" SOLID WD. CLEAT -CONT.2X STUD PARTITION -REFER TO FLOOR PLAN FOR SIZEBATT INSULATION - REFER TO WALL TYPE SCHED. FOR R-VALUE3X WD. BACKING PLATE - SEE DETAIL /15AD.021/4" DIA. X 3" L. SHT. MTL. SCREWS @ 6" O.C. -(USE S.S. FINISH WASHERS & SCREWS W/ VINYL COLORED PLUGS AT OPEN SHELVING)1/2" MIN. X 3" SOLID WD. CLEAT -CONT.NOTE:ANCHORAGE PER WIC # OPA-2649-102X STUD PARTITION -REFER TO FLOOR PLAN FOR SIZEBATT INSULATION - REFER TO WALL TYPE SCHED. FOR R-VALUE3X WD. BACKING PLATE - SEE DETAIL /15AD.023X WD. BACKING PLATE - SEE DETAIL 1/4" DIA. X 3" L. SHT. MTL. SCREWS @ 6" O.C. - (USE S.S. FINISH WASHERS & SCREWS W/ VINYL COLORED PLUGS AT OPEN SHELVING)1/2" MIN. X 3" SOLID WD. CLEAT -CONT.2X STUD PARTITION - REFER TO FLOOR PLAN FOR SIZEBATT INSULATION - REFER TO WALL TYPE SCHED. FOR R-VALUEFULL HT. BACKSPLASH TO UNDERSIDE OF UPPER WALL CABINET WHERE OCCURS - REFER TO CASEWORK SCHEDULESEALANT/15AD.023X6 BLOCKING BETWEEN STUDSA34 CLIPS EA. END TOP & BOTTOM @ ALL GRAB BAR LOCATIONS -END NAIL AT ALL OTHER LOCATIONS2X STUDS @ 16" O.C.SOLID SURFACE COUNTERTOP REFER TO FINISH SCHEDULE 1/4" CABINET BACKINGSEE INT. ELEV.WIRE PULLS - TYP.WHITE MELAMINE AT SEMI-EXPOSED AREA - TYP.DRAWERDRAWERP. LAM. FINISH AT ALL EXPOSED SURFACES -REFER TO FIN. SCHED.WALL BASE - REFER TO FINISH SCHEDULEDRAWERAD.029AD.027FIN. FLR.AD.0251 1/2" DIA. S.S. GRAB-BAR W/ CONCEALED MOUNTS TO WALL3X BACKING - SEE DETAIL+33" A.F.F.FLANGE ELEVATION3/8" MOUNTING HOLESS.S. FLANGE18 GA. S.S. HANDRAIL ARMLOCKING DIMPLESSTAINLESS STEEL COVER PLATEATTACH GRAB BAR FLANGE TO BACKING W/ (2) #1/4"-14 X 2-1/2" TEK SCREWSCERAMIC WALL TILE - REFER TO FINISH SCHEDULE2X STUD PARTITION - REFER TO FLOOR PLAN FOR SIZEBATT INSULATION - REFER TO WALL TYPE SCHEDULE FOR R-VALUE1 1/2"/15AD.02SIMFINISH CEILING - REFER TO R.C.P2X STUD PARTITION - REFER TO FLOOR PLAN FOR SIZEWHITE MELAMINE AT SEMI-EXPOSED AREAS - TYP.P. LAM. FINISH AT ALL EXPOSED SURFACESDRILLED HOLES TO ACCEPT SHELF CLIPFIXED SHELF - SEE INTERIOR ELEVS (ADJ. SHELF WHERE DOORS ARE FULL HEIGHT)DOORS SHALL HAVE CONCEALED HINGESWIRE PULLS - TYP.ADJ. SHELF - TYP. U.O.N.P. LAM. DOOR(S) - SEE INTERIOR ELEVATIONS FOR DOOR CONFIGURATION1/4" CABINET BACKING4"FIN. FLR.REFER TO R.C.P.AD.027WALL BASE - REFER TO FINISH SCHEDULEBATT INSUL. - REFER TO WALL TYPE SCHEDULE FOR R-VALUESEE PLANAD.029AD.0252"X2"X 1/4" ANGLE STL. BRACKETPLUMB. TRAP & PIPE - S.P.D.2X BLOCKING - TYP. EA. SIDE OF WALL STUDSOLID SURFACE COUNTERTOP BACKSPLASH & APRON4"2'-10" MAX. TO FIN. FLR.5"2"X2"X 1/4" STL. ANGLE BRACKET @ 32" O.C. W/ 3/4" M.B.2'-1"1 1/2" TYP.3"1/2"2"2"ADA PROTECTIVE PIPE COVER AT EACH LAVATORY - TYP.CERAMIC TILE - SEE FINISH SCHED.NOTE:1. PLACE THE HEIGHT OF CABINET SO THAT THE TOP OF THE F.E. HANDLE IS 4'-0" A.F.F.2. IT IS NOT REQUIRED TO ADD FRAMING IF THE CABINET WIDTH MATCHES THE SPACE BETWEEN THE STUDS OR IF 1 1/2" OF SHIM ON ONE SIDE WILL FILL THE SPACE ALONG WITH THE CABINET. INCREASE THE LENGTH OF THE SCREWS TO ADJUST FOR THE THICKNESS OF THE SHIM.FRAMING ELEVATIONFIRE EXTINGUISHER CABINET ROUGH OPENING -25" X 10 1/2" X 1-1/2". VERIFY SIZE / VERIFY LOCATION ON FLOOR PLANPROVIDE 2x6 BLOCKING AT TOP & BOTTOM2X FRAMING - REFER TO FLOOR PLAN FOR SIZE & SPACING13AD.022X WOOD STUD @ EA. SIDE & ONE AT TOP & BOTTOM. SEE FLOOR PLANS FOR APPLICABILITY(3) #8 x 1 1/2" R.H.W.S. EACH SIDE & ONE AT TOP & BOTTOM2:A-10:B:C FIRE EXTINGUISHER(1) LAYER OF 5/8" GYP. BD.2X STUD PARTITION -REFER TO FLOOR PLAN FOR SIZE5/8" GYP. BD.FIBERGLASS REINFORCED PANEL -REFER TO FINISH SCHED.CONC. SLAB -S.S.D.BACKER ROD AND SEALANTHORIZONTAL ALUM. TRIM1X3 RDWD. SUPPORT CLEAT ON BOTH WALLSMOP SINK AND TRIM -S.P.D.SEMI-RECESSED FIRE EXTINGUISHER CABINET W/ 2:A-10:B:C FIRE EXTINGUISHERTOP OF FIRE EXTINGUISHER4'-0"PULL HANDLE WITH LOCKTEMPERED GLASSF.F.SUSPENDED ACOUSTICAL TILE CEILINGREFER TO SUSPENDED CEILING DSA IR 25-2.13 LISTFOR ATTACHEMENT OF LIGHT FIXTURES, FLEXIBLE SPRINKLER HOSE FITTINGS, CEILING-MOUNTED AIR TERMINALS, CEILING MOUNTED PROJECTORS AND OTHER MISCELLANEOUS.METAL MAIN RUNNER OR CROSS TEE45°4 5 °PROJECTOR CEILING PLATE ATTACH w/ 1/4-20 STS TO MAIN CEILING RUNNERS PER MANUF.1 1/2"ø TUBE COLUMNPROJECTOR BRACKETPROJECTOR & COMPLETE ASSEMBLY MAX WEIGHT SHALL NOT EXCEED 30LBS.CENTER & ALIGN PROJECTOR LENS TO CENTER OF PROJECTION SURFACEPROJECTOR ELECTRICALS TO KNOCK OUTS(4) TIGHT TWISTS @ HANGER WIRE WITHIN 1-1/2" - TYP. @ BOTH ENDS OF WIRE#12 GA BRACING WIRE @ EA. PROJECTOR MOUNT CORNER & PER MANUF INSTRUCTIONS - TYP.1-1/2" MAX.1-1/2" MAX.3"W X 4"L X 12 GA. STEEL STRAP - BEND TO ALIGN WITH WIRE WHERE OCCURSWD. ROOF TRUSS - TYP. -S.S.D.ROOF SHEATHING - S.S.D.WOOD STUD FRAMING -REFER TO FLOOR PLAN FOR SIZE & SPACING(4) 1/4" DIA. x 3" LONG WOOD SCREWS AT EA. STUD. 2 1/2" EMBEDMENTPEERLESS MODEL #SF650 SMART MOUNT UNIVERSAL FLAT WALL MOUNTFLAT SCREEN T.V. (N.I.C.) 39"-75" MAX. WEIGHT 150 LBSMAX. 4"BATT INSULATION -REFER TO SCHEDULE FOR R-VALUEGYP. BD. - REFER TO FINISH SCHEDULE FOR FINISHMOUNT CENTER OF MONITOR @7' - 0" A.F.F. - VERIFY W/ OWNER1'-1"2'-6"SOLID SURFACE VERTICAL EDGEDRAWERSOLID SURFACE PANEL1'-0" 2'-0"DRAWERDRAWERDRAWERP.LAM CASEWORK BACKINGWIRE PULLS - TYP.MELAMINE AT SEMI-EXPOSED AREAS - TYP.P. LAM. FINISH AT ALL EXPOSED SURFACES - REFER TO FINISH SCHEDULEWALL BASE - REFER TO FINISH SCHEDULESOLID SURFACE COUNTERTOP REFER TO FINISH SCHEDULE FIN. FLR.P.LAM CASEWORK BACKING1'-0" 2'-0"1 1/2"1'-1"2'-6"FIN. FLR.P. LAM. FINISH AT ALL EXPOSED SURFACES - REFER TO FINISH SCHEDULEWALL BASE - REFER TO FINISH SCHEDULESOLID SURFACE COUNTERTOP REFER TO FINISH SCHEDULE 4"3"SOLID SURFACE COUNTERTOP -TYP.P.LAM CASEWORK BACKING4"P.LAM TOE KICKP.LAM FINISH AT ALL EXPOSED SURFACES2'-8"FIN. FLR.2'-6"3/4" PLYWD. W/ P.LAM @ UNDERSIDE OF S.S. COUNTER3"FLOOR TILE- REFER TO FINISH SCHEDULEVINYL FLOORING INSTALL PER MANUF. SPECS & REFER TO FINISH SCHEDULETRANSITION STRIP "SCHLUTER" OR EQUAL METAL - COLOR AS SELECTED BY ARCHITECT1/2" MAXFALIOFCSeptember 2021SS T A TEERIILCWCENH OC28388AIRNL EWOITARCHEDAILLIMECT Checked By:Drawn By:Project No.:LDA Partners, Inc.Designers & Architects222 Central CourtStockton, CA 95204209.943.0405www.ldapartners.comClient:Project:Architect:450 COMMERCE COURT,MANTECA, CA. 953366/3/2021 5:07:30 PMDETAILSAD.02AuthorChecker727-01-18PERMIT SUBMITTAL #206/02/2021MACHADO SPORTS PARK1020 MARSH CREEKEBMA INVESTMENTSMANTECA, CA 953363" = 1'-0"AD.025BASE CABINET @ TOE KICK1" = 1'-0"AD.024ACCESS. BASE CABINET AT SINK3" = 1'-0"AD.0210BASE CABINET ANCHOR AT WALL3" = 1'-0"AD.029ACCESS. BASE CAB. ANCHOR AT WALL3" = 1'-0"AD.027CABINET TOP ANCHOR3" = 1'-0"AD.028UPPER CABINET LOWER ANCHOR1" = 1'-0"AD.0215WOOD BACKING1" = 1'-0"AD.023BASE CAB. W/ DRAWERS AT WALL3" = 1'-0"AD.0214GRAB BAR MOUNTING1" = 1'-0"AD.022FULL HEIGHT CASEWORK SECTION1 1/2" = 1'-0"AD.026LAVATORY COUNTER1" = 1'-0"AD.0212FIRE EXTING. CAB. FRAMING ELEV.3" = 1'-0"AD.0213FIRE EXTINGUISHER CAB. SECTION3" = 1'-0"AD.0216MOP SINK1" = 1'-0"AD.0211FIRE EXTING. CABINET1 1/2" = 1'-0"AD.0218PROJECTOR CEILING MOUNT TO ROOF Copy 11" = 1'-0"AD.0219MONITOR MOUNT1" = 1'-0"AD.0221LOBBY CASEWORK AT DRAWERS1" = 1'-0"AD.0222LOBBY CASEWORK AT KNEE SPACE1" = 1'-0"AD.0223LOBBY CASEWORK AT SERVICE DESK6" = 1'-0"AD.0220TILE TO LVT TRANSITIONNo. Description Date By5/18/2021, 8:35:15 AM21-0396Roseville Submittals6/8/2021, 1:58:25 PM21-0396LUMEN ARCEO