Laserfiche WebLink
ARB Approved IOM — Executive Orders VR-201-G and VR-202-G (Swivel Breakaway—807) Page 40 <br /> Healy Model 807 Swivel Breakaway <br /> IMPORTANT:This sheet must be left with service station manager. <br /> HEALY STAGE II VAPOR RECOVERY MODEL NOZZLE END <br /> 807 SWIVEL BREAKAWAY(HOSE BREAK) <br /> ASSEMBLY&INSTALLATION INSTRUCTIONS <br /> • The Healy Swivel Breakaway is delivered loosely assembled. Handle <br /> carefully to avoid dropping and/or losing the precision parts. N <br /> ■ Failure toremove the Shear screw (Item 9) as described in <br /> Step 1 below could result in fracturing or shearing of the screw <br /> The Shear screw will require replacement if damaged. ° <br /> ■ Be sure to assemble parts in the exact sequence as shown below. <br /> w . <br /> ■ Be sure to lubricate all o—rings and quad seals where indicated. <br /> Use of ordinary motor oil is sufficient. <br /> ■ Do not use thread—sealing compounds on straight threads. <br /> ■ This Breakaway shall be installed between the product hose <br /> and the nozzle end (threaded onto nozzle). <br /> 11 <br /> V <br /> J <br /> N <br /> O <br /> ASSEMBLY INSTRUCTIONS <br /> (refer to diagram at right) D <br /> SEE <br /> NOTE <br /> 1. Remove the Shear Screw (Item 9) and the packing materials. <br /> Separate the halves of the breakaway assembly, retaining the o <br /> loose internal valve, (Item 6) and the spring (Item 11) inside <br /> the halves. <br /> 2. Install the male threaded half of the 807 into the Healy Nozzle. <br /> Lubricate the o—ring seals (Items 17 & 21 and tighten to <br /> 35 to 70 foot pounds.Be sure the vapor tube fitting slides easily into <br /> the nozzle before final tightening. <br /> 3. Select the delivery hose, lubricate the o—ring seals and straight <br /> thread. Assemble the non—swivel end of the Breakaway on the <br /> hose.Tighten to 35 to 70 foot pounds.Be sure the valve and spring <br /> (items 6&11)are in place before final tightening. <br /> 4. Carefully fit both halves of the Breakaway together. Utlizing <br /> the alignment pin, fully compress both halves and insert the HOSE <br /> Shear Screw (Item 9) and hand tighten. Final tighten to 20 <br /> inch pounds. Tools should not be necessary to initially start <br /> the Screws. *NOT FIELD REPLACEABLE <br /> 27 2 4125-514GJ QUAD RING,MINNISOTA RUBBER 80727 <br /> 21 1 1_025 0-RING,PRECISION #5747 HB-2 <br /> 20 1 1-122 0-RING,PRECISION #9727 709 <br /> 19 2 1-024 0-RING,PRECISION #5747 MPD-5 <br /> 18 1 1-117 0-RING,PRECISION @9727 708 <br /> 17 6 1-012 0-RING,PRECISION #5747 75414 <br /> 16 1 1-009 0-RING,PRECISION /9727 753 <br /> 11 1 A8701-752 SPRING,CONICAL 752 <br /> 9 2 B8701-787 SCREW,SHEAR 787-1 <br /> 6 1 A8701-748 VALVE,DISPENSING END 748 <br /> 4 1 B8701-810 BUSHING 810 <br /> O2 1 C8701-805 SNIVEL FEMALE,(MACHINED) 805 <br /> 1 1 CB701-609 BODY.DISPENSER END 809 <br /> NOTE:SHEAR SCREW INSTALLS 45°FROM SPARE. ITEM No. QTr owc N0. OESCRIPT ON P/N <br /> UST OF MATERIAL <br /> HEALY SYSTEMS, INC. healy <br /> 18 Hampshire Drive * Hudson, New Hampshire 03051 ...the SMART Stage llsolution <br /> (603) 882-2472 Telephone* (603) 882-5189 FAX <br /> A3701-807-INST-M <br /> 11 INN REV.M <br /> Franklin Fueling Systems Website: http://www.franklinfueling.com <br /> 3760 Marsh Road Email: sales@franklinfueling.com <br /> Madison, Wisconsin 53718 USA Telephone: 800-225-9787 <br /> ARB Approved Installation, Operation and Maintenance Manual Fax: 608-838-6433 <br /> HEALY <br /> Franklin Fueling Systems <br />