|
m
<br />PIPING MATERIAL SCHEDULE
<br />ABBREVIATIONS
<br />DWV COPPER
<br />LEGEND AND
<br />SYMBOLS
<br />INDIRECT WASTE
<br />GENERAL NOTES
<br />48. PROVIDE ACOUSTO-PLUMB TYPE PIPE ISOLATOR AT HANGERS FOR ALL PLUMBING PIPING. PROVIDE ON ALL WATER DISTRIBUTION
<br />3
<br />a
<br />ABOVE GRADE
<br />X
<br />49. FOR CONCEALED AND EXPOSED INTERIOR STORM DRAIN PIPING, INSULATE THE UNDERSIDE OF ROOF DRAIN BODIES AND ALL
<br />COLD WATER
<br />1. OWNER SHALL PAY AND OBTAIN FOR ALL REQUIRED UTILITY SERVICES, INSPECTIONS AND PERMITS.
<br />WITH ALL SERVICE JACKET, EQUAL TO OWENS CORNING TYPE SSLIL JACKET SHALL BE SEALED TO UNDERSIDE OF ROOF ALL
<br />AROUND ROOF DRAIN BODIES; LAP AND SIAL ALL JOINTS.
<br />ABOVE GRADE
<br />DCV'
<br />DCV DOUBLE CHECK VALVE
<br />- (E) {E}
<br />EXISTING LINE
<br />0
<br />i�
<br />;a
<br />.0
<br />2. ALL WORK SHALL COMPLY WITH THE 2016 CALIFORNIA PLUMBING CODE.
<br />1
<br />5
<br />3J �
<br />R o P
<br />RPBP REDUCE PRESSURE BACKFLOW PREVENTER
<br />SS
<br />ABOVE FLOOR SANITARY SEWER PIPING
<br />3. PRIOR TO BIDDING, THE CONTRACTOR SMALL OBTAIN COPY OF THE PLANS AND SPECIFICATIONS AND EXAMINE THEM. ANY
<br />AC
<br />AIR CONDITIONING UNIT
<br />HZ
<br />FREQUENCY (HERTZ)
<br />I
<br />POC POINT OF CONNECTIONDISCREPANCIES
<br />-�- S5
<br />BELOW FLOOR SANITARY SEWER PIPING
<br />OR CONFLICTS IN THE DRAWINGS AND/OR SPECIFICATIONS SHALL BE BROUGHT TO THE ARCHITECT AND/OR
<br />ENGINEER, IN WRfINGI BEFORE BIDS ARE SUBMITTED, NO ALLOWANCE WILL BE MADE FOR FAILURE TO SUBMIT DISCREPANCIES TO
<br />ACCU
<br />AIR COOLED CONDENSING UNIT
<br />ID
<br />INSIDE DIAMETER
<br />THICK UNE REPRESENTS (N} WORK
<br />THIN LINE REPRESENTS (E) WORK
<br />THE ARCHITECT AND/OR ENGINEER.
<br />AD
<br />ACCESS p00R
<br />IE
<br />INVERT ELEVATION
<br />P,O,C,
<br />ESS ESS
<br />EXISTING SEWER
<br />IN DETAIL
<br />AD
<br />AREA DRAIN
<br />IFC
<br />IN FURRED CEILING
<br />PIPE UNION
<br />4. PRIOR TO START OF CONSTRUCTION WORK, PLUMBINQ CONTRACTOR SHALL SUBMIT DErAILE 5HOP DRAWING 6QEQUATE
<br />ENGINEER,
<br />AFF
<br />ABOVE FINISHED FLOOR
<br />IFS
<br />IN FURRED SPACE
<br />EGW EGW
<br />EXISTING GREASE WASTE
<br />FOR REVIEW AND APPROVAL BY THE ARCHITECT 6ND/-QR
<br />AFG
<br />ABOVE FINSIHED GRADE
<br />IFW
<br />IN FURRED WALL
<br />3
<br />PIPE CAPPED
<br />ECW ECW
<br />EXISTING COLD WATER
<br />5. CONTRACTOR SHALL CLOSELY COORDINATE WORK WITH ALL TRADES.
<br />AHU
<br />AIR HANDLING UNIT`
<br />IIS
<br />IN JOIST SPACE
<br />SOLENOID VALVE
<br />6. VERTICAL AND HORIZONTAL OFFSETS SHOWN IN PIPES INDICATE THE GENERAL RELATIONSHIP OF THE SYSTEMS. PROVIDE ADDITIONAL
<br />AHS
<br />AIR HANDLING SYSTEM
<br />IN
<br />INCH
<br />_ _ - _ _ - _ r V
<br />VENT PIPING (SANITARY)
<br />OFFSETS SIMILAR TO THOSE SHOWN AS REQUIRED TO SUIT CONSTRUCTION AND WORK DONE BY OTHER TRADES. THE CONTRACTOR
<br />AL
<br />ACOUSTIC LINING
<br />INWG
<br />1NCHS OF WATER, GAUGE
<br />�--/�
<br />SOV SHUT-OFF VALVE, PIAN /RISER
<br />SHALL PROVIDE ALL. NECESSARY ACCESSORIES AS REQUIRED FOR A COMPLETE INSTALLATION.
<br />AP
<br />ACCESS PANEL
<br />I.E./INV
<br />INVERT ELEVATION
<br />_- - - CW
<br />DOMESTIC COLD WATER SUPPLY PIPING
<br />7 ALLETC. SHALL BE INSTALLED IN ACCESSIBLE LOCATIONS. PROVIDE ADEQUATELY SIZED ACCESS DOORS
<br />APD
<br />AIR PRESSURE DROP {INWG}
<br />JS
<br />JANITOR SINK
<br />��--•��
<br />BLV BALANCING VALVE
<br />BCW
<br />BOOSTED DOMESTIC COLD WATER SUPPLY PIPING
<br />RE©TROLS,
<br />ARCH
<br />ARCHITECTURAL.
<br />KS
<br />KS
<br />KITCHEN SINK
<br />-�.r
<br />COV COMBINATION BALANCING &
<br />BCW
<br />8. EXAMINE ARCHITECTURAL DRAWINGS TO ENSURE THAT ALL PIPING CROSSING FIRE AND/OR SMOKE SEPARATION CONSTRUCTION
<br />AS
<br />AIR SEPARATOR
<br />KILOWATT
<br />SHUT-OFF VALVE
<br />_-- -- HW
<br />DOMESTIC HOT WATER SUPPLY PIPING
<br />SHA D BE SEALED WITH UL LISTED ASSEMBLIES.
<br />ATV
<br />ACOUSTIC TURNING VANES
<br />LAV/L
<br />LAVATORY
<br />9• SEE ARCHITECTURAL DRAWINGS FOR EXACT LOCATION AND MOUNTING HEIGHTS OF ALL PLUMBING FIXTURES.
<br />B
<br />BOILER
<br />LBS
<br />POUNDS
<br />�P
<br />--���
<br />PRV PRESSURE REDUCING VALVE
<br />--- HWR
<br />DOMESTIC HOT WATER RETURN PIPING
<br />BFF
<br />BELOW FINISHED FLOOR
<br />LF
<br />LINEAR FEET
<br />10. OFFSET VENTS AT ROOF AS REQUIRED TO MAINTAIN 10 FEET SEPARATION FROM ANY AIR INTAKE, DOORS, OPERABLE WIND OWS AND
<br />BFG
<br />BELOW FINISHED GRADE
<br />SGV SEISMIC GAS SHUT-OFF VALVE
<br />TW TW
<br />TEMPERED WATER SUPPLY PIPING
<br />TERRACES. GATHER ALL VENTS IN PROXIMITY IN ATTIC SPACE TO MINIMIZE TERRACES/ROOF PENETRATIONS.
<br />LG
<br />LENGTH
<br />BHP
<br />BRAKE HORSEPOWER
<br />LS
<br />LAUNDRY SINK
<br />VALVE
<br />G G
<br />NATURAL GAS PIPING
<br />11. PROVIDE 3/8 INCH COLD WATER SUPPLY TO ICE MAKER BOXES/REFRIGERATOR FROM KITCHEN SINK COLD WATER SUPPLY, WHEN
<br />BOP
<br />BOTTOM OF PIPE
<br />LWB
<br />LEAVING WET BULB
<br />---� Z�I-
<br />BV BALL
<br />REQUIRED. PROVIDE 3/8 INCH HOT WATER SUPPLY TO DISHWASHER FROM KITCHEN SINK HOT WATER SUPPLY. SUPPLY
<br />BT
<br />BATH TUB
<br />LWT
<br />LEAVING WATER TEMPERATURE
<br />..
<br />DIRECTION OF FLOW
<br />IW IW
<br />IW INDIRECT WASTE PIPING
<br />SHALL BE COMPLETE WITH SHUTOFF VALVE AND WATER HAMMER ARRESTOR, WHERE REQUIRED BY UPC.
<br />BTU
<br />BRITISH THERMAL UNIT
<br />MAX
<br />MAXIMUM
<br />CD CD
<br />CONDENSATE DRAIN PIPING
<br />12. HORIZONTAL SANITARY SEWER PIPES SHALL HAVE 1/4' PER FOOT MINIMUM SLOPE OR 2X%X MINIMUM FLOW TOWARDS THE
<br />CD
<br />CONDENSATE DRAIN
<br />MBH
<br />1 DDO BTUS PER HOUR
<br />HOSE END GATE VALVE WITH HOSE CAP
<br />DISPOSAL AREA.
<br />GFH
<br />CUBIC FEET PER HOUR
<br />MECH/MECH'L MECHANICAL
<br />FS FS
<br />FIRE SPRINKLER PIPING
<br />13, ALL HOSE BIBS SHALL BE PROVIDED WITH NDN -REMOVABLE BACKFLOW PREVENTION DEVICE.
<br />CFM
<br />CI
<br />CUBIC FEET PER MINUTE
<br />CAST IRON
<br />MER
<br />MECHANICAL EQUIPMENT ROOM
<br />BALANCING VALVE\PWTTH MEMORY STOP
<br />F F
<br />FIRE WATER SUPPLY PIPING
<br />14. ALL WATER AND DRAINAGE PIPING SYSTEMS SHALL BE INSTALLED WITH ACOUSTICAL ISOLATORS AND SHALL BE ISOLATED FROM ANY
<br />CLG
<br />CEILING
<br />MFR
<br />MANUFACTURER
<br />GW GW
<br />GREASE WASTE PIPING
<br />STRUCTURAL MEMBERS, WALL SECTIONS OR OTHER MATERIALS THAT COULD TRANSMIT SOUND TO THE OCCUPIED AREAS.
<br />CO
<br />CLEANOUT
<br />MIN
<br />(N)
<br />MINIMUM
<br />NEIN
<br />��
<br />���
<br />BALL VALVE
<br />15. PIPING PENETRATIONS OF STRUCTURAL MEMBERS SHALL BE IN ACCORDANCE WITH STRUCTURAL DRAWINGS AND MUST BE
<br />CONN
<br />CONNECTION
<br />_
<br />DIRECTION OF FLOW
<br />RISER UP (ELBOW)
<br />COORDINATED WITH THE TRADES INVOLVED BEFORE MAKING THE PENETRATIONS.
<br />N/A
<br />NOT APPLICABLE
<br />CONC
<br />CONCRETE
<br />NC
<br />NORMALLY CLOSED/NOISE CRITERIA
<br />FCO
<br />FCO FLOOR CLEANOUT
<br />RISER DOWN (ELBOW)
<br />16. PLUMBING CONTRACTOR SHALL BE RESPONSIBLE FOR SPACING COORDINATION OF WOOD FRAMING AND SPECIAL CONDITIONS
<br />CONTR
<br />CONTRACTOR
<br />REQUIRED FOR INSTALLATION OF PLUMBING WORK. SEE ARCHITECTURAL AND STRUCTURAL DRAWINGS FOR OBSTRUCTION FROM
<br />CPC
<br />CALIFORNIA PLUMBING CODE
<br />NIC
<br />NOT IN CONTRACT
<br />CO 2W
<br />FCO(2W) FLOOR CLEANOUT TWO-WAY
<br />�-
<br />RISE OR DROP
<br />DOUBLE SIDED SHEAR WALLS AND SPECIAL HOLD-DOWN POST ASSEMBLY.
<br />CTG
<br />CLEAN OUT TO GRADE
<br />NIPW
<br />NOT IN PLUMBING WORK
<br />NORMALLY OPEN, NUMBER
<br />GCO
<br />GCO GRADE CLEANOUT
<br />17. PLUMBING CONTRACTOR SHALL CONNECT TO SITE SEWER AND DOMESTIC COLD WATER SUPPLY WITHIN 5 FEET OUT OF BUILDING
<br />CW
<br />COLD WATER (DOMESTIC)
<br />NO
<br />BRANCH -SIDE CONNECTION
<br />LINE. SEE CIVIL SITE UTILITY DRAWINGS FOR EXACT LOCATIONS AND INVERT ELEVATIONS.
<br />CW
<br />CLOTHES WASHER
<br />NPT
<br />NATIONAL PIPE THREAD
<br />CO 2W G
<br />GCO(2W) GRADE CLEANOUT TWO-WAY
<br />DCV
<br />DOUBLE CHECK VALVE
<br />INTS
<br />NOT TO SCALE
<br />!
<br />CLEANOUT PLUG
<br />`��r
<br />BRANCH -TOP CONNECTION
<br />18. ALL PIPING ON PLANS is TYPICALLY SHOWN CONCEALED IN CEILING OR PLUMBING WALLS, RISERS AND OFFSETS SHALL B
<br />IN WALLS OR CEILING UNLESS OTHERWISE NOTED.
<br />�
<br />ON CENTER
<br />! _
<br />1
<br />.l,
<br />CONCEALED
<br />DIA
<br />DN
<br />DIAMETER
<br />DOWN
<br />OD
<br />OUTSIDE DIAMETER
<br />I I
<br />FD FLOOR DRAIN
<br />x
<br />BRANCH -BOTTOM CONNECTION
<br />19. EACH PLUMBER USING A TORCH TO SWEAT PIPE JOINT SHALL HAVE ACCESS TO 2A RATED FIRE EXTINGUISHER AT WORK AREA AND
<br />OFD
<br />OVERFLOW DRAIN
<br />SHALL FIRE WATCH FOR 1/2 -HOUR AFTER USE, IN COMPLIANCE WITH THE 2016 CALIFORNIA FIRE CODE REQUIREMENTS.
<br />DWGS
<br />DRAWINGS
<br />®
<br />FSK FLOOR SINK (1/2 GRATE)
<br />0
<br />DIAMETER
<br />P
<br />PUMP
<br />20. PROVIDE SEISMIC SHUTOFF VALVE DOWNSTREAM OF GAS METER.
<br />PDi
<br />PLUMBING AND DRAINAGE INSTITUTE
<br />(E)
<br />EXISTING
<br />PH
<br />PHASE
<br />21. ALL PIPING PENETRATING CONCRETE FLOOR OR WAIL MUST BE PROVIDED WITH SLEEVE TO PREVENT PIPE BREAKAGE.
<br />EA
<br />EACH
<br />PBLG
<br />PLUMBING
<br />22. FURNISH AND INSTALL ANY INCIDENTAL WORK NOT SHOWN OR SPECIFIED WHICH IS NECESSARY TO PROVIDE A COMPLETE AND
<br />EL/ECFV
<br />ELEC/ELECT
<br />ELEVATION
<br />ELECTRICAL
<br />POC
<br />POINT OF CONNECTION
<br />LEGEND, SYMBOLS
<br />AND ABBREVIATION NOTE
<br />WORKABLE SYSTEM.
<br />ESP
<br />ELEVATOR SUMP PUMP
<br />PRESS
<br />PRESSURE
<br />23. FOR EXACT LOCATIONS OF PLUMBING FIXTURES, FLOOR DRAINS, FLOOR SINKS, ROOF DRAINS, AREA DRAINS, DECK DRAINS.
<br />EXPANSION TANK
<br />SOV
<br />SHUT OFF VALVE
<br />"LEW0, SYIIIBOLS APD ABBMMATKM LISTED ARE FOR SSE. AL U
<br />DOWNSPOUT AND HOSE BIBS, SEE ARCHITECTURAL DRAWINGS AND DETAILS.
<br />24. KEEP ALL PLUMBING PIPING AS HIGH AS POSSIBLE TO STRUCTURE ABOVE AND OFFSET AS REQUIRED.
<br />ET
<br />ENTERING WATER TEMPERATURE
<br />SPD
<br />SUMP PUMP DISCHARGE
<br />SUMP PUMP VENT
<br />DISREGARD THOSE INI'�CF� ARE NOT USED ON TM DRAWNti.S"
<br />25. COORDINATE WITH CML DRAWINGS FOR SITE CONNECTIONS TO FIRE, COLD WATER, GAS SANITARY WASTE AND RAINWATER
<br />F
<br />FILTER
<br />SPV
<br />STUBOUTS.
<br />(F)
<br />FUTURE
<br />SS
<br />STAINLESS STEEL
<br />'F
<br />FAHRENHEIT IN DEGREES
<br />SS
<br />SANITARY SEWER
<br />26. ANY CONFLICT IN THE DRAWINGS AND/OR SPECIFICATIONS, SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT ENGINEER
<br />S HEFT INDEX
<br />FOR RESOLUTION PRIOR TO THE CONSTRUCTION OF SUCH ITEMS.
<br />FA
<br />FROM ABOVE
<br />T
<br />THERMOSTAT
<br />FB
<br />FROM BELOW
<br />TC
<br />TIME CLOCK
<br />27. ALL PIPING PENETRATIONS THROUGH RATED WALT, CEILING OR FLOOR SHALL BE PROTECTED BY AN APPROVED PEN ETRAnON
<br />FCO
<br />FLOOR CLEANOUT
<br />TEMP
<br />TEMPERATURE
<br />P1.0 GENERAL NOTES, SYMBOLS AND ABBREVIATIONS
<br />FIRESTOP SYSTEM INSTALLED AS TESTED IN ACCORDANCE WITH ASTM EB14 (UL 1479), WITH A MINIMUM POSITIVE PRESSURE
<br />DIFFERENTIAL OF 0.01 INCH OF WATER AND SHALL HAVE AN F RATING OF NOT LESS THAN THE REQUIRED FIRE -RESISTANCE
<br />FD
<br />FLOOR DRAIN
<br />TP
<br />TRAP PRIMER
<br />P2.0 PLUMBING FLOOR PLAN
<br />RATING OF THE WALL PENETRATED.
<br />FF
<br />FINISHED FLOOR
<br />N
<br />TURNING VANES
<br />FIFE
<br />FINISHED FLOOR ELEVATION
<br />TYP
<br />TYPICAL
<br />28. COORDINATE ROUGH -IN OF ALL WORK WITH EQUIPMENT/FIXTURE REQUIREMENTS AND OTHER TRADES.
<br />FLA
<br />FULL LOAD AMPS
<br />UG
<br />UNDERGROUND
<br />29. ALL PLUMBING EQUIPMENT SHALL BE SECURELY FASTENED TO THE BUILDING STRUCTURE.
<br />FLEX
<br />FLEXIBLE
<br />UL
<br />UNDER WRITER'S LABORATORY
<br />30. ALL FLOOR MOUNTED PLUMBING EQUIPMENT SHALL BE ON CONCRETE PADS OR CONCRETE CURBS. PROVIDE 4" HIGH CONCRETE
<br />FLR
<br />FLOOR
<br />UL
<br />UNLESS OTHERWISE NOTED
<br />HOUSEKEEPING PAD UNDER ALL FLOOR MOUNTED PLUMBING EQUIPMENT. COORDINATE HOUSEKEEPING PAD LOCATIONS AND SIZES
<br />FPM
<br />FEET PER MINUTE
<br />UR/U
<br />URINAL
<br />WITH THE STRUCTURAL ENGINEER AND WITH THE GENERAL CONTRACTOR.
<br />FPS
<br />FEET PER SECOND
<br />V
<br />VENT
<br />31. INSTALL ACCESS PANELS IN ALL NON -ACCESSIBLE CEILINGS AND WALLS FOR ACCESS TO VALVES, CLEANOUTS AND OTHER
<br />FS
<br />FLOOR SINK
<br />VIF
<br />VERIFY IN FIELD
<br />MAINTENANCE ITEMS. REFER TO ARCHITECTURAL PLANS FOR TYPE OF CEILINGS AND WALLS. INSTALL FIRE RATED ACCESS PANELS
<br />FT
<br />FEET
<br />VR
<br />VENT RISER
<br />IN FIRE RATED CEILING AND WALLS. SEE ARCHITECTURAL SPECIFICATIONS FOR ACCESS PANELS. COORDINATE WITH GENERAL
<br />FM
<br />FEET OF WATER, GAUGE PRESSURE
<br />VTR
<br />VENT THRU ROOF
<br />CONTRACTOR FOR LOCATIONS OF ACCESS
<br />FT
<br />SQUARE FEET
<br />W
<br />WASE
<br />32. WHERE MAIN PIPE SIZE 1S NOT INDICATED BETWEEN BRANCH CONNECTIONS IN THE DRAWING, THE PIPE SIZE SHALL BE OF THE
<br />FU
<br />FIXTURE UNIT
<br />WC
<br />WATER CLOSET/WATER COLUMN
<br />LARGER PRECEDING PIPES
<br />HTR
<br />HEATER
<br />WCO
<br />WALL CLEANOUT
<br />33. ALL VALVES AND ACCESSORIES SHALL BE FULL TINE SIZE. PROVIDE All NECESSARY UNIONS, REDUCERS AND STOPS AS REQUIRED
<br />HW
<br />HOT WATER (DOMESTIC)
<br />WH
<br />WATER HEATER
<br />WHEN CONNECTING TO EACH FIXTURE AND/OR EQUIPMENT.
<br />HWR
<br />HOT WATER RETURN (DOMESTIC)
<br />WHA
<br />WATER HAMMER ARRESTOR
<br />34. PROVIDE CLEANOUTS ON DRAINAGE LINES IN ACCORDANCE WITH THE PLUMBING CODE AND AS INDICATED ON THE DRAWINGS.
<br />wr
<br />WEIGHT
<br />35. PROVIDE DEEP SEAL TRAPS ON ALL FLOOR DRAINS INCLUDING FLOOR SINKS IN MECHANICAL ROOMS.
<br />PIPING MATERIAL SCHEDULE
<br />PIPE
<br />DWV COPPER
<br />TYPE "L" COPPER
<br />REMARKS
<br />INDIRECT WASTE
<br />BELOW GRADE
<br />48. PROVIDE ACOUSTO-PLUMB TYPE PIPE ISOLATOR AT HANGERS FOR ALL PLUMBING PIPING. PROVIDE ON ALL WATER DISTRIBUTION
<br />3
<br />a
<br />ABOVE GRADE
<br />X
<br />49. FOR CONCEALED AND EXPOSED INTERIOR STORM DRAIN PIPING, INSULATE THE UNDERSIDE OF ROOF DRAIN BODIES AND ALL
<br />COLD WATER
<br />BELOW GRADE
<br />WITH ALL SERVICE JACKET, EQUAL TO OWENS CORNING TYPE SSLIL JACKET SHALL BE SEALED TO UNDERSIDE OF ROOF ALL
<br />AROUND ROOF DRAIN BODIES; LAP AND SIAL ALL JOINTS.
<br />ABOVE GRADE
<br />50, PORTABLE WATER SYSTEM SHALL BE DISINFECTED PRIOR TO USE AS REQUIRED BY THE AUTHORITY HAVING JURISDICTION. USING
<br />X
<br />THE FOLLOWING PROCEDURES PRESCRIBED IN CPC SEC. 609.9.1 THRU 609.9.4 AND INCLUDING SEC.604.1.2 FOR PEX PIPING.
<br />NOTES:
<br />1. SUSPENDED PIPING SHALL BE SUPPORTED AT INTERVALS NOT TO EXCEED THOSE SHOWN IN CPC TABLE 3-2.
<br />2. HANGER ROD SIZES SHALL BE NO SMALLER THAN THOSE SHOWN IN CPC TABLE 3-1.
<br />36. ALL HORIZONTAL RAIN WATER PIPING WITHIN BUILDING FOOTPRINT SHALL BE SLOPED AT 1/8" PER FOOT MINIMUM UNLESS
<br />OTHERWISE NOTED ON THE DRAWING.
<br />37. PROVIDE INDIVIDUAL SHUT-OFF VALVE/SUPPLY STOP TO ALL PLUMBING FIXTURES AND EQUIPMENT.
<br />38. ALL HORIZONTAL GAS PIPING SUPPORTED ON RODS OVER 12 INCHES IN LENGTH SHALL BE SEISMICALLY BRACED.
<br />39. ALL DRAINS FROM RELIEF VALVES, CONDENSATE PANS, COILS AND HVAC EQUIPMENT HAVING DRAINS SHALL BE PIPED TO NEAREST
<br />DRAIN UNDER THIS SECTION OF WORK.
<br />40. ALL PIPING IN CONCRETE FOUNDATIONS, AND WALLS, INCLUDING BLOCK WALLS SHALL BE FULLY INSULATED TO ISOLATE PIPING
<br />FROM CONCRETE.
<br />41. ALL PLUMBING FIXTURES AND PIPING SHALL BE LISTED BY AN APPROVED LISTING AND TESTING AGENCY AND PROPERLY LABELED
<br />PER CPC SECTION 301.1.1.
<br />42. ALL WATER CLOSETS SHALL HAVE A MAXIMUM OF 1.28 GPF.
<br />43. ALL DOMESTIC WATER VALVES UP TO AND INCLUDING 2" SIZE SHALL BE BRASS OR OTHER APPROVED MATERIALS. EACH GATE
<br />VALVE SHALL BE A FULL --WAY TYPE WITH WORKING PARTS OF NON -CORROSIVE MATERIAL PER CPC 605.1.
<br />44. PROVIDE ALL GAS BURNING EQUIPMENT WITH EXCESS FLOW VALVE DEVICES.
<br />45. FIRST 5 FEET OF HOT AND COLD WATER PIPES CLOSEST TO WATER HEATER TANK, NON -RECIRCULATING SYSTEMS, AND ENTIRE
<br />LENGTH OF RECIRCULATING SECTIONS OF HOT WATER PIPES ARE INSULATED PER TITLE 24 STANDARDS TABLE 150--8.
<br />46 PROVIDE WATER HAMMER ARRESTER WHERE QUICK -ACTING VALVES ARE INSTALLED IN THE WATER SUPPLY SYSTEM TO ABSORB
<br />( � 1
<br />STORE # 13357
<br />1201 WEST MAIN STREET
<br />RIPON, CA 95337
<br />OWNER
<br />DOLLAR GENERAL
<br />100 MISSION RIDGE
<br />GOODLETTSVILLE, TN 37072
<br />REVISIONS
<br />CONSULTANT
<br />B E L D E N
<br />013m0U1_-r1r4G EIVGINEEI213
<br />5860 W. Las Positas Boulevard, Suite 15
<br />Pleasanton, California 94588
<br />phone: (925) 621-5300 fax: (925} 474-2159
<br />belden@beldeninc.com
<br />19142E / MW
<br />SEAL
<br />Q p�tOfESSION,��
<br />0 YO(�N
<br />M33081
<br />N Ex 6/3 /21
<br />OF C A\ -\F
<br />Dsm
<br />ARCHITECTS
<br />TITLE
<br />GENERAL NOTES,
<br />SYMBOLS AND
<br />ABBREVIATIONS
<br />ISSUED SHEET
<br />08/28/2019
<br />SUBMITTAL
<br />- Pi mo
<br />JOB NO.
<br />19538
<br />COPYRIGHT D PSM ARCHITECTS, 2019
<br />HIGH PRESSURES RESULTING FROM THE QUICK CLOSING OF THESE VALVES. SIZING AND INSTALLATION SHALL BE IN ACCORDANCE
<br />WITH PLUMBING AND DRAINAGE INSTITUTE (PDI). TO COMPLY WITH CPC 609.10.
<br />47. PROVIDE A 12" LONG DRIP LEG AT ANY POINT IN THE GAS LINES WHERE CONDENSATE MAY COLLECT. ALL DRIPS SHALL BE
<br />READILY ACCESSIBLE TO PERMIT CLEANING OR EMPTYING.
<br />48. PROVIDE ACOUSTO-PLUMB TYPE PIPE ISOLATOR AT HANGERS FOR ALL PLUMBING PIPING. PROVIDE ON ALL WATER DISTRIBUTION
<br />3
<br />a
<br />PIPES REQUIRE INSULATION PER CF -1R OF THE TITLE 24.
<br />0
<br />a
<br />49. FOR CONCEALED AND EXPOSED INTERIOR STORM DRAIN PIPING, INSULATE THE UNDERSIDE OF ROOF DRAIN BODIES AND ALL
<br />INTERIOR DRAIN PIPING BOTH HORIZONTAL AND VERTICAL INCLUDING HUBS AND FITTINGS WITH 1 INCH THICK RIGID FIBERGLASS
<br />WITH ALL SERVICE JACKET, EQUAL TO OWENS CORNING TYPE SSLIL JACKET SHALL BE SEALED TO UNDERSIDE OF ROOF ALL
<br />AROUND ROOF DRAIN BODIES; LAP AND SIAL ALL JOINTS.
<br />0
<br />50, PORTABLE WATER SYSTEM SHALL BE DISINFECTED PRIOR TO USE AS REQUIRED BY THE AUTHORITY HAVING JURISDICTION. USING
<br />THE FOLLOWING PROCEDURES PRESCRIBED IN CPC SEC. 609.9.1 THRU 609.9.4 AND INCLUDING SEC.604.1.2 FOR PEX PIPING.
<br />! ar
<br />0
<br />i�
<br />;a
<br />.0
<br />J �
<br />1
<br />5
<br />3J �
<br />Q
<br />_ o
<br />a ..
<br />�z
<br />3 II
<br />_ N
<br />I (II
<br />L)
<br />o �
<br />U_
<br />( � 1
<br />STORE # 13357
<br />1201 WEST MAIN STREET
<br />RIPON, CA 95337
<br />OWNER
<br />DOLLAR GENERAL
<br />100 MISSION RIDGE
<br />GOODLETTSVILLE, TN 37072
<br />REVISIONS
<br />CONSULTANT
<br />B E L D E N
<br />013m0U1_-r1r4G EIVGINEEI213
<br />5860 W. Las Positas Boulevard, Suite 15
<br />Pleasanton, California 94588
<br />phone: (925) 621-5300 fax: (925} 474-2159
<br />belden@beldeninc.com
<br />19142E / MW
<br />SEAL
<br />Q p�tOfESSION,��
<br />0 YO(�N
<br />M33081
<br />N Ex 6/3 /21
<br />OF C A\ -\F
<br />Dsm
<br />ARCHITECTS
<br />TITLE
<br />GENERAL NOTES,
<br />SYMBOLS AND
<br />ABBREVIATIONS
<br />ISSUED SHEET
<br />08/28/2019
<br />SUBMITTAL
<br />- Pi mo
<br />JOB NO.
<br />19538
<br />COPYRIGHT D PSM ARCHITECTS, 2019
<br />
|