Laserfiche WebLink
Wiring for 4'1 Connect 4 to 20 mA wiloa lu luullllyd luun(I 1'133 as <br />shown in the figure. <br />Refer to the latest revision of Ilio :;iiInt!1 •1 p,() Il rbidimeter <br />Manual (3-4150.090) for further Info unr 1111 to <br />4150 via 8058.1 ° = Technical Nolo::: <br />® 5 All of the elecb ical <br />i ® I connections to the <br />+Iu - + I instrument are made <br />aCrG through the terminal box. <br />I The connections are <br />" • --11, labeled within the terminal <br />box and are self -descriptive. <br />„ A plug is inserted into the <br />RS -485 cable bulkhead <br />.. Indlno r. <br />�? <br />i when shipped to ensure a _ g6 watertight seal. Remove <br />and discard this plug when <br />III cabling to this connection. <br />+ lrsI......... ';' 'rh(; bulkhead will accept <br />........... ____ iti ', cnblediameters from <br />'-- !0I nun (0.23 in.) up to <br />mPnl 10 nuts (0.34 in.). The <br />1'11-'°A <br />lot 1) are designed to <br />uccopl wires in the range <br />of Irl (o 28 AWG. All wires <br />utack !should be stripped to a <br />stood 11 111 fill of G mm (0.25 in.). <br />Parer Rud I n::nn.! That the watertight <br />Cannecuen -- _ ;nnl Ir maintained after <br />Ih❑ Icinimal box has been <br />what l Int operation. If any ,' <br />4150 via 8058-2 of Ihtr hfilkheads are not <br />fill 'ht[ Iifoperly around 4 <br />® i c111'1(! of plug, the ratings _ <br />+-... 'y+ nilhnumhmmentwill be <br />11n111i11111/(,'d'ifidthere is <br />n Innmilrifily o creating a <br />'Illlwli I1i1: ala <br />1111 not 1im rl to 20 mA <br />P'ullllelPUl71rU �, — JAI111,t; ontI In two, cables in <br />fill, liunp, r, ldoil. <br />F Tuchnicnl NMos: <br />Whon u;:intl Ism H(1b14 ; <br />!S <br />connect the loop sourt:c to <br />t - <br />+.I •-'••-••--- ®;•� Channel 1 input ONLY. <br />® Qz, GDi2 <br />Y <br />� 0 <br />PJR.�d <br />Black ilc(Gnd) <br />s'L) <br />milck(B Ver) <br />Power <br />Connection <br />12 8800 Trlefefniter Start -Up Guide <br />+GP+ <br />� QCAUTION! <br />DO NOT connect your 9900 to AC power. <br />The 9900 MUST be powered by 10.8 to 35.2 VDC ONLY. _I <br />Stand-alone application, no current loop used <br />ProcessPro <br />(for reference only) 9900 <br />Transmitter <br />Terminals 8900 <br />Terminals <br />Syslom Pwr Loop - 4 Lilnrk _ Power <br />Rod <br />+ PWR <br />System PWT Loop r 3 Supply Power Supply <br />R,>,1 1210 24 VOC Loop - Pil - 10.0 to 35.2 VOC <br />AUX Prnvcr- 0 2--_; Loop. �m 01nck <br />AUX Power. Leap - <br />Connection to a PLC/Recorder, separate supply <br />ProcessPro <br />(for reference only) 9900 <br />Transmitter <br />Terminals Blue <br />PLC or Recorder <br />i <br />Loop Inpul <br />SY+tem Rvr Loop- <br />O.a.-....-... <br />,,__ <br />ply <br />- <br />4 to 20 mA <br />syctcm Pwr Loop + <br />.3. <br />+ <br />AUX Power- <br />2 <br />Black <br />_ Power <br />AUX Povmr <br />e t <br />Red <br />Supply <br />rdertA <br />1210 24 VOC <br />AUX power required for all 8750-2 systems <br />Loop Powered <br />ProcessPro <br />(for reference only) <br />Transmitter <br />i Terminals <br />System Pwr Loop - 4 Black Power <br />System P- Loop . 02 Supply <br />to 24 VOC <br />AUX P.—, . O 2 <br />AUX Paver+ O t PLC or Recorder <br />1 Red -Loop Input <br />e to 20 mA <br />i <br />j! <br />I <br />9s0o <br />Terminals <br />PWR a Red Power Cupr1Y <br />I�WR 111.0 to ]fi.2 VOC <br />Loop + <br />❑lua <br />UP_ <br />LC or Recorder <br />LoopInput <br />4 to 20mA <br />9900 <br />19900 <br />Terminals <br />PWR +WRcd- <br />ply <br />PWR <br />VOCLoop <br />+ <br />Loop - <br />rdertA <br />NOTE: Loop Power <br />cannot be used to power <br />certain Signet sensors. <br />See table on pg, 7. <br />9900 Transmitter Start -Up Guide 13 <br />