_O & M MANUAL - WEST LANE MOBILE HOME PARK

Home Browse Search

Board Power W I., MR",3 ® Ji I I If the green power ELECTRICAL SHOCK HAZARD Aatus indicators are not 0:S=r4necl ail pc:,'e: wwces "Wcr luminated: Etta;g. FaiuEeW•asac :, res=i ^'�Eil.1t3S E^jUR';1"c'!✓; r7. 1. Check to see if the fuses on the circuit board are blown. 2. Check to see if the incoming controlialarrn power is present at TBI -1 and TBI -Z If voltage is present and fuse is not blown, please call factory for assistance. Circuit Breaker (optional) Check each pole of the circuit breakerfor proper resistance reading using the following procedure: Warning: Disconnect all incoming power to control panel. Failure to do so could result in serious or fatal electrical shock. 1. Isolate the circuit breaker by disconnecting either the line side or load side wires. 2. Place the ohmmeter lead's across the corresponding line and load terminals of each pole. 3. With the ohmmeter on the R X 1 scale and the breaker in the OFF position, the reading should be infinity (very high resistance). With the breaker in the ON position, the reading should be nearly zero ohms (very low resistance). If the readings are riot as stated, replace the circuit breaker with one of the sante ratings. Alarm Horn Moving the test/normal/silence switch to the test position or activating the alarm float should turn on the alanm horn. If the horn does not sound, replace horn with same type. Alarm Light Moving the testtnormallsilence switch to the test position or activating the alarm float should turn on the alarm light. If the light does not activate, replace with bulb of same type. SJE-RH4MSUS1" warrants to the original consumer that this prod- uct shall be free of manufacturing defects for five years after the date of consumer purchase. During that time period and subject to the conditions set forth below, SJE-RHOMBUS-' will repair or replace, for the original consumer, any component which proves to be defective due to defective materials or workmanship of SJE- RHC MBUS". ELECTRICAL WIRING AND SERVICING OF THIS PRODUCT MUST BE PERFORMED BY A LICENSED ELECTRICIAN. THIS WARRANTY DOES NOT APPLY: (A) to damage due to lightning or conditions beyond the control of SJE-RHOMBUS-; (B) to defects or malfunctions resulting from failure to properly install, operate or maintain the unit in accordance with printed instructions provided; (C) to failures resulting from abuse, misuse, accident, or negligence; (D) to units which are not installed in accordance with _ipplicabie local codes, ordinances, or accepted trade practices, and (E) to units repaired s,ndlor modified without prior authorization from SJE-RHi`3MBUS�. Check the floats during their entire range of operation. Cleary, adjust, or replace damaged floats. Checking the float resistance - The Moat resistance can be measured to determine if the float is operating correctly or is defective. Use the following procedure to measure the float resistance. Warning: Disconnect all incoming power to panel. Failure to do so could result in serious or fatal electrical shock. 1. isolate the float by disconnecting one or both of the float leads from the float terminals. 2. Place one ohmmeter lead on one of the float wires, and the other ohmmeter lead on the other float wire. 3. Place the ohmmeter dial to read ohms and place on the R X 1 scale. With the float in the "off' position, the scale should read infinity (high resistance). Replace the float if you do not get this reading. With the float in the ON position, the scale should read nearly zero (very low resistance). Replace the float if you do not get this reading. NOTE: Readings may vary depending on the length of wire and accuracy of the measuring device. Fuses Check the continuity of each fuse. With power OFF, pull the fuses out of the fuse blocks. With the ohmmeter on the R X 1 scale, measure resistance. A reading of infinity indicates a blown fuse and must be replaced. Replace fuse with same type, voltage and amp rating, Magnetic COntaCIOF Coli Warning: Disconnect all incoming power to panel. Failure to do so could result in serious or fatal electrical shock. Check the coil by disconnecting one of the coil leads. Measure the coif resistance by setting the ohmmeter on the R X 1 scale. A defective coil will read zero or infinity, indicating a short or opened coil respectively. Replace defective contactor with same type. Some states do not allover limitations on how long an implied warranty lasts, so the above limitation may not apply to yore. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation orexr1usion may not apply to you. This warranty gives you specific: legal rights, and you may also have other rights which var,r from state to state, TO OBTAIN WARRANTY SERVICE: The consumer shall assume all responsibility and expense for removal, reinstallation, and freight. Any iters to be repaired or replaced under this warranty must be returned to SJE-RHC MBUSO, or such place as designated by SJE-RHOMBUS". NOTICE! Products returned must be cleaned, sanitized, or decontaminated as necessary prior to shipment to ensure that employees will not be exposed to heath hazards in handling said material. All applicable laws and regulations shall apply.