Laserfiche WebLink
POWER CORD (16) <br />CAP SCREW (11) <br />LOCKWASHER (12) <br />COMPRESSION FLANGE (16a) <br />SNAP RING (19) <br />O-RING (20) <br />TERMINAL BLOCK (21) <br />FIGURE 14 <br />Reconnect motor and optional control leads to the underside <br />of the terminal block(s) (21), (54 optional) as shown in Figure <br />13. Note that the pins are numbered underneath the terminal <br />block. Place o -ring (20) into groove in terminal block and <br />lubricate with dielectric oil. Press the terminal block (21) <br />into the housing so it seats completely below the snap ring <br />groove. Place snap ring (19) into groove in cable entry bore of <br />housing. Repeat terminal block installation for control cable, if <br />equipped. <br />F-4.4) Cable Assemblies: <br />Power/Control Cable- Refill the cooling oil as outlined in <br />paragraph F-1.3. Make wire connections as outlined in <br />paragraph F-4.3. Insert female end of cable plug into housing <br />bore aligning timing mark with hole in terminal block (21) see <br />Figure 15. Compress cable plug with compression flange <br />(16a) by tightening hex bolts (11) into the housing (6). Torque <br />to 132 in -lbs. <br />SECTION: G REPLACEMENT PARTS <br />G-1 ORDERING REPLACEMENT PARTS: <br />When ordering replacement parts, ALWAYS furnish the <br />following information: <br />1. Pump serial number and date code. (Paragraph G-4) <br />2. Pump model number. (Paragraph G-3) <br />3. Pump part number. (Paragraph G-2) <br />4. Part description. <br />5. Item part number. <br />6. Quantity required. <br />7. Shipping instructions. <br />&. Billing Instructions. <br />15 <br />CONTROL CORD (56) <br />CAP SCREW (11) <br />LOCKWASHER (12) <br />COMPRESSION FLANGE (56a) <br />SNAP RING (19) <br />O-RING (20) <br />TERMINAL BLOCK (54) <br />�} H �dl CUde i~Il. ii?. U <br />ja i Iu <br />Fe:,f N'; 3 kSerial No. \ { <br />M <br />Imaeller Go. �(�y az o I !i s. I�„ Y <br />WARS N N G TO REDUCE RISK OF i <br />ELECTRICAL SHOCK DISCONNECT THE <br />p PUMP FROM THE POWER SOURCE BEFORE i <br />HANDLING OR SERb1C:NG. SEE 1 <br />:NSTTUC7QN MANUAL FOR PROPER <br />NS':ALLATION. SEE WARNING PLATE "OP. 0 <br />ADD TIONAL CAUTIONS. <br />G-2 PART NUMBER: <br />The part number consists of a six (6) digit number, which <br />appears in the catalog. A one or two letter suffix may follow <br />this number to designate the design configuration. This <br />number is used for ordering and obtaining information. <br />G-3 MODEL NUMBER: <br />This designation consists of numbers and letters which <br />represent the discharge size, series, horsepower, motor <br />phase and voltage, speed and pump design. This number is <br />used for ordering and obtaining information. <br />G-4 SERIAL NUMBER: <br />The serial number block will consist of a six digit number, <br />which is specific to each pump and may be preceded by <br />a alpha character, which indicates the plant location. This <br />number will also be suffixed with a four digit number, which <br />indicates the date the unit was built (Hate Code). <br />EXAMPLE: A012345 0490. <br />Reference the six digit portion (Serial Number) of this number <br />when referring to the product. <br />