_O & M MANUAL - WEST LANE MOBILE HOME PARK

Home Browse Search

opening preventing stagnate areas where solids can settle. The basin or pit must be capable of supporting the weight of the pump and guide rail. The pit floor must be flat. NOTICE: FOLLOW THE INSTRUCTIONS THAT ARE PROVIDED WITH THE GUIDE RAIL ASSEMBLY. PIPING Discharge piping should be no smaller than the pump discharge diameter and kept as short as possible, avoiding unnecessary fittings to minimize friction losses. Install an adequately sized check valve matched to the solids handling capability of the pump to prevent fluid backflow. Backflow can allow the pump to "turbine" backwards and may cause premature seal and/or bearing wear. If the pump is turning backwards when it is called on to start the increased torque may cause damage to the pump motor and/or motor shaft and some single-phase pumps may actually run backwards. Install an adequately sized gate valve AFTER the check valve for pump, plumbing and check valve maintenance. Important — Before pump installation. Drill a 3/16" (4.8mm) relief hole in the discharge pipe. It should be located within the wetwell, 2" (51mm) above the pump discharge but below the check valve. The relief hole al- lows any air to escape from the casing. Allowing liquid into the casing will insure that the pump can start when the liquid level rises. Unless a relief hole is provided, a bottom intake pump could "air lock" and will not pump �1 water even though the impeller turns. ( / All piping must be adequately supported, so as not to impart any piping strain or loads on the pump. The pit access cover must be of sufficient size to allow for inspection, maintenance and crane or hoist service. WIRING AND GROUNDING Important notice: Read Safety Instructions before proceeding with any wiring. AUse only stranded copper wire to pump/motor and ground. The ground wire must be at least as large as the power supply wires. Wires should be color coded for ease of maintenance and troubleshooting. AInstall wire and ground according to the National Electrical Code (NEC), or the Canadian Electrical Code, as well as all local, state and provincial codes. AInstall an all leg disconnect switch where required by code. ADisconnect and lockout electrical power before performing any service or installation. AThe electrical supply voltage and phase must match all equipment requirements. Incorrect voltage or phase can cause fire, motor and control damage, and voids the warranty. AAll splices must be waterproof. If using splice kits follow manufacturer's instructions. A WARNING I Select the correct type and NEMA grade junction box for the application and loca- tion. The junction box must insure dry, safe wiring connections. 4 A WARNING Seal all controls from gases present which may damage electrical components. AWARNING FAILURE TO PERMANENTLY Hazardous GROUND THE PUMP, MOTOR AND voltage CONTROLS BEFORE CONNECTING TO POWER CAN CAUSE SHOCK, BURNS OR DEATH. SELECTING AND WIRING PUMP CONTROL PANELS AND SWITCHES FLOAT SWITCH TYPES There are two basic float switch designs; single-action and wide-angle. Single-action switches operate over a range of 15° so they open and close quickly. Wide-angle floats operate over a 90° swing with the tether length be- tween the float body and the pivot point controlling the On -Off range. The design determines how many floats are required with different systems or controls. Floats may be normally open (NO) for pump down applications or to empty a tank. Normally closed (NC) switches are used to pump up or to fill a tank. A single-action control switch may be used only with a control panel, never direct connected to a pump. The wide-angle, pump down switches may be used as direct connected pump switches or as control switches. SETTING THE FLOAT SWITCHES There are no absolute rules for where to set the float switches, it varies from job to job. Suggested Rules to Follow: All floats should be set below the Inlet pipe! Off Float: Best: set so the water level is always above the top of the pump (motor dome). Next Best: set so the wa- ter level is not more than 6" below the top of the pump. On Float: set so the volume of water between the On and Off floats allows pumps of 1'/z HP and under to operate for 1 minute minimum. Two (2) HP and larger pumps should run a minimum of 2 minutes. Basin literature states the gallons of storage per inch of basin height. Lag/Alarm Float(s): should be staggered above the Off and On floats. Try to use most of the available storage provided by the basin, save some space for reserve stor- age capacity. See Diagrams and Charts in Float Switch Chart Section. PANEL WIRING DIAGRAMS Our control panels are shipped with instructions and wir- ing diagrams. Use those instructions in conjunction with this IOM. Electrical installation should be performed only by qualified technicians. Any problem or questions pertaining to another brand control must be referred to that control supplier or manufacturer. Our technical people have no technical schematics or trouble shooting information for other companies' controls. ALARMS We recommend the installation of an alarm on all Waste- water pump installations. Many standard control panels come equipped with alarm circuits. If a control panel is not used, a stand alone high liquid level alarm is avail- able. The alarm alerts the owner of a high liquid level in the system so they can contact the appropriate service personnel to investigate the situation.