COMPLIANCE INFO_2023 - Laserfiche WebLink

Home Browse Search

B2000 RETROFIT KIT UDC #34 INSTALLATION INSTRUCTIONS DISPENSER A FACTORY-PROVIDED IIT FOR SEALING PRODUcrAND CONDUIT ENTRIES ON LEGACY 8-2000 SW1LLOw UOC'S. (e) SHEAR VALVE (e) VAPOR SHEAR VALVE r (e)1SHEAR VALVE FR- ES1 RETROFIT (e) BRAVO SHALLOW BOX - FEF-EBS CONDUIT FITTING - r For this fitting remove the existing hoot 8 clamps, clean the l r. "r contact surfaces of any/all contaminants, abrade the contact surfaces of both P Pes and install the RES1 splitlit FRP sleevecentere . 1 J. steel coupler itth foam cord or other material first. Then d overthe pack each half with Bravo epoxy, join Nem together and secure with t ` clamps to cure. Bead with vu kem where it contacts the floor. jd •., 8 - 18 - 3 Compression Fitting - PRODUCT REPAIR ENTRY FITTINGS B- 18-3 orientation - r � The bass secondary line test plug located - within the hotly should be at a 90° degree angle from any flat wall. If it is at any other INCLUDED 1x VS-B - Caulk tube of Black Vulkem 116 polyurethane sealant angle, the filling is not installed correctlyJ.' BELOW DISPENSER 3x FR-ES1 - 2"o split FRP clarnshell x 2.5• tall and/or the gasket is not flat against the Moor. COMPONENTS : 3x FR"MYE-5 - 3"o split FRP clamshell x 1 .5" tall Whether the gasket isseatedfinnlyto he floor 3x ADHESIVE-EPDXY-RETROFIT-KIT - Bravo FRP Epoxy or not, or if the orientation is incorrect, the 3x Pairs of large gloves 3x Sur sticks Vulkem sealing method outlined below is the Coareras su1i To 6x 2" hose clamps 1x Sheet of sandpaper best way to make a lasting liquid-tight seal. CHANGE wmroUT Nance ax 3" hose Clamps When prossur�tmakes this seal. the secondary: the UDC #7- 8 top nut makes this seal. The Bass plug should not be removed. If leaks occur from the lop nut/donut then loosen them with WD-40 if 2. 91 PRODUCT LINE necessary andseat with wet-dry grease. ` r Then tighten the nut than ut ro more 114 - 1R hums past hand tight TEST BOOT �� .�--� { 13 - 18 - 3 Vulkem Seal ISR 3.5x2.4OSA WARNING ! The lower nut of the —91 &1 &3 frttmg must not be loosened wdboul he the . . :r + Fitting ng body may ened too or fall donut thugh he r. coon resslon donut secure) sealed against the ope. drop _ — FR- MYE - 5 RETROFIT if boh are loosened ton murk the & 1 &3 bottom of the shallow pan. MYERS HUB ( MYE) CONDUIT UPPZR NUT - Mer cleaning all contact areas horougtYy use FITTING For MYE's, clean the exterior of the fitting vulkem to seal between he bottom nut and flat p and sand he epoxy paint oft of the steel floor about 1" out LOWKI- NUT gasket With the top nut secured to the pipe, r ' from its outer diameter- Apply Bmvo epoxy to interior of loosen the lower nut and apply vulkem under FR-MYE-5 split FRP sleeve and install over the MYE fining the nut and generously to the exposed threads DSL !- I with clamps- Ensure it is completely encapsulated with no of the body. Do not dislodge the flat gasket or t'' l tapped air. Then apply a generous bead of vulkem to the apply vulkem between it and the floor of the ,m outsloe of the FRP sleeve where it contacts the floor. Be vulxcm MT shallow. Lubrication can cause it to slip loose VAPOR sure to re-coat any steel that was exposed from sanding / or pinch once tightened musing a leak polnt. F cleaning. Just above 1. where commonly another pipe protudes through and a conduit comes through that pipe, r�-- follow the FR-ESI retrofit directions above to seat these two pipes to each other. B-27 Compression Fitting - VAPOR - 131=11 -112 VAPOR FITTING - - You do not need to worry about the B-27 fitting body UNITED PACIFIC #54`'47 Clean the exterior surfaces of the fitting and repeat the dropping dawn or falling through the bottom of the shallow 1469 E . HAMMER LN . ti instructions listed above for the Myers Hub fitting It is pan if the vapor fine Is threaded into the top or this fitting. If a iz .. common for a vapor shear valve to be threaded directly "�T smaller line is passing through it however, it may drop down STOCKTO N CA. 95209 onto this type of fitting. fl so. hen he FR-MYE-S should and out so use caution and secure the body above the floor t ' apply, but if there is a nipple above, then the FR-ES1 mayas you loosen the nut to test it REPAIRS PG . 2 O F 3 SCALE: _ also be needed. It is detailed below and shown on the left DATE: 2-3-2023 , As NOTE In the case where his fitting was Instead used as a conduitAfter cleaning all contact areas thoroughly, use vulkem to entry, (as shown) first Install the FR-ES1 to the lop-most seal between the rut and flat gasket and also to he exposed F CGRS part of the threads and the conduit that protrudes through. threads of the body. Do not apply vulkem between the flat C G RS , INC . gasket and the floor of he shallow pan or dislodge this _° �° °� °r° 5444 DRY CREEK ROAD vuLKEM gasket Lubrication can cause it to slip loose or pinch once IL tightened musing a leak point SACRAMENTO , CA . 95838