WORK PLANS - Laserfiche WebLink

Home Browse Search

RATIONAL ICP 6-HALF NG 120V 1 PH (LM10013G) Item#E-053 iCombi Pro 6-half size E/G Technical specifications Dimensions and weights Connected loads-gas Dimensions(W x H x D) Voltage 2 AC 208 V Cooking system(body) 33 1/2 x 29 5/8 x 30 1/2 inches Connected loads-gas 0.6 kW Cooking system(total) 33 1/2 x 31 5/8 x 33 1/8 inches Breaker 15A Cooking system with packaging 36 3/4 x 37 3/4 x 37 5/8 inches RCD Type B Maximum working height of top level' <-5 ft.2 7/8 inches Voltage 1 NAC 120V `When using an original RATIONAL stand Connected loads-gas 0.6 kW Breaker 15 A Weights RCD Type F Maximum load size per level 331b Maximum total load capacity 661b All gas units are supplied with cord. Weight-electric unit without packaging 218 Ib Connection conditions water Weight-electric unit with packaging 257 Ib Water inlet(pressure hose),each 3/4" Electrical connection conditions Water pressure(flow pressure),each 14.5-87.0 psi Voltage 3 AC 208 V/240 V Water drain,each 2"OD Connected loads-electric 10.8 kW Maximum flow rate per cooking system 3.17 gal/min Steam power 9 kW Water quality requirements Convection power 10.25 kW Untreated water can be 0 to 24.5 gr/gal(0 to 420ppm)hardness.We do Breaker 35A not recommend treated water hardness<5 gr/gal(86ppm)because the RCD type B water could be corrosive.Sodium ion exchangers are not recommended; H+Ion exchange systems are recommended.Water that does not meet Cable diameter AWG 8140°F the following minimum standards will require the proper conditioning Voltage 3 AC 440 V/480 V Contaminant Water Requirements If>than recom- Connected loads-electric 10.8 kW mended Steam power 9 kW Sand/Particles <15 Nm Particle filter Convection power 10.25 I<W Chlorine(Cl2) <0.12 gr/gal(0.2 ppm) Active carbon filter Breaker 20A Chloride(CI-) <4.68 gr/gal(80 ppm) RO RCD type B Cable diameter AWG 14 140°F Connected loads-exhaust air and thermal load Voltage 2 AC 208 V/240 V Latent heat load 1943 BTU Connected loads-electric 10.8 kW Sensible heat emission 2391 BTU Steam power 9 kW Sound level(electric) 55 dBA Convection power 10.25 kW Sound level(gas) 60 dBA Breaker 60 A RCD type B Connection loads-data Cable diameter AWG 4 140°F LAN data interface RJ45 Not supplied with cable connection WiFi data interface IEEE 802.11 a/g/n Minimum distances at installation _ Clearance Requirements Connected loads-gas To facilitate servicing,we recommend leaving a 20"(500 mm)gap on the left-hand side of the unit.If there is not 20"(500 mm)left side clearance Natural gas G20 available,provisions for moving the unit to the left for service access o Nominal heat load,total 49500 BTU must be made.Such provisions include,but are not limited to,having Nominal heat load,Steam mode 45500 BTU quick connections(water,gas,etc.)and lengthened electrical connections v Nominal heat load,Hot Air mode 49500 BTU with flexible cords. If there are no external heat sources acting on the unit,there should be at v Required connection Flow pressure 6.5-10 inch w.c. least 2"(50 mm)of clearance on either side of the unit.The back of the 3 Liquid gas unit can be mounted flush with the wall. a Nominal heat load,total 48500 BTU If a high temperature heat source is on the left side of the unit,clearance Nominal heat load,Steam mode 44500 BTU of at least 14"(350 mm)must be maintained on the left-hand side.This o N clearance may be reduced to 2"(50 mm)if a heat shield is used(see Nominal heat load,Hot Air mode 48500 BTU o accessories). M Required connection flow pressure 10-15 inch w.c. Recommended clearance From unobstructed rear exhaust pipes and any 3/4"NPT with 3/4"gas shut off surface collecting grease or flammable material;16"(400 mm)gas, Additional gas types and voltages available on request 10"(254 mm)electric.It is recommended to have a hood overhang of `s 6"(150 mm)to 18"(450 mm)at the front of the unit and 6"(150 mm)on a v 4/8 Den-Stockton 03/03/2022 ADVANTAGE EQUIPMENT SALES-LLC Page:95