Laserfiche WebLink
5} DipoUck number (Kj = 82" <br />Tarok diameter (1'1 = 92" <br />M- (x1= {Zl <br />(7) = 10" <br />dl (V 2•Ac (10" 20PWin <br />C=8" <br />71 Is 8' less than 6=1 /2? <br />No Measure the distance from the tap of the 400 race. Face Seal Adaptnt installed on the riser pipe <br />to the inside, top lip of the storage tank and ole <br />rain measurernent(A) <br />U pper tuFx length _ C + jA) <br />For tastable modols+aith, eatding in "T^: Upplri Tribe <br />Length = C + (A) - 1-112^ <br />R5SEMBLY fNsfftUr.f1UN5 <br />IMPOIITAHIT: Each of the nu m�ered steps in the in- <br />stallation instructions aredesigned as a CHECK LIST to <br />ensure proper Installation and trouble free operation of <br />the OPW 71SO Overfill Prevention Valve. <br />Read and foHuw these seeps carefully, checking them <br />off a s you proceed. <br />Figure numbers correspond eo step numb <br />ersforeasy <br />reference, <br />STEP 1: MEASURE <br />Install the i]PW Face Seal Adaptor and the OPW Tnread- <br />en Sep Container on the FI(I Riser !Refer to rhe fnsrdafa <br />uort Instructions Supplied with the Sp it Container]. In- <br />sert a tape measure through the riser pipe and hook It <br />under the Inside of the tank in the lengthwise diredion, <br />Measure the. distance from the top of the Face Seat <br />Adaptor threads Inside the base of the spill contalner <br />bucket just below the drain valve outlet window to the <br />inside, top lip of the storage tank (Dim. "A) (Sala Figrme <br />1 WAI. <br />The top flange on the 71 SO w 11 rest on the Face Seal <br />Adaptor }ust below the drain valve outlet, and be <br />locked in place between the Face Seat Adaptor and the <br />4' nipple that is installed in the spill contelnerWith the <br />Jack Screw Kit (Sola Figura 1A). (for riser pipe configure <br />tions other than that shown, consult insta;iadon draw - <br />Ings or use other necessary means to measure DiMenL <br />slon `Al. <br />Using a tape measure, measure the distance from the <br />top of the Fate Seal Adaptor in the spill container to the <br />bottom of the tank {Dim.'BI, <br />11NPOSTANT: inspect the riser pipe for any loretyn Mate- <br />rial, over spray from tank relining or any internal burls <br />inside of pipe must be removed prior to installation - <br />Failure to have an unobstructed riser pipe may prevent <br />pr operinstallationar+doperatronOfthevalve, The <br />7 t SD k designed for installation Irrto schedule 40 riser <br />pipes. The 71 SO cannot be Installed into schedule 80 <br />h ser pipes. <br />STEP 2: li{ARIitHE FUBE <br />Use the result from Step 1 and HGM/TQ LOCA7F 7HE <br />Pt76MON OFTHE71SOArm TANRCApAtr►yto <br />mark the upper tube. Measure the distance from the <br />seam where the upper tube and valve body meet. Use <br />a tape measure to mark the caleutated upper tube <br />length onto the tipper tube, See Figum 2 <br />Pape measure <br />I'..a k r <br />INN Ftpa <br />wih Fax CAi <br />6eMAdomor To Tank (91 <br />To I.D.] To TW* <br />90 <br />f/grrr+e 1 <br />isvrrlr 7A <br />