COMPLIANCE INFO_PRE 2020 - Laserfiche WebLink

Home Browse Search

CHECK VALVE tOUTLET) CHECK VALVE MUT LET!! CONTROL VALVE IN4 j T NEATER CONTROL VALVE CHECK VALVE liblrfLET) APR-06-99 10:43 AM GEREMIA POOLS 916 277 1537 P. C13 TO OPEN CHEMICAL FEELIcR: shut off pump and turn Dial Control Valve to OFF_ Wait 1 minute. (If outlet is below water level, close any ether in- line valves to prevent possible water back flow.) Turn Cover Cap counter-clockwise to open. Use SP- 3100T cover opening tool if necessary. Caution: Do not inhale fumes from feeder. Allow water In lank to drain automatically to pool. II chemical feeder is installed below water level, open the Drain Valve and allow the tank to drain in a safe manner, Draining the tank should make adding sanitizer easier and safer. TO REFILL CHEMICAL FEEDER: Add desired quantity of either Trichloro-S-Triazinetrione (Iri- chlor) slow dissolving chlorine or bromine tablets or slicks. Never mix chemicals together or use any other type of chlorine sanitize( in this feeder. Explosion or fire may result causing properly damage, personal injury or death. TO CLOSE CHEMICAL FEEDER: 1. Be sure cover 0-Ring is in place. Engage Cover threads and turn clockwise to secure. Hand lighten only. 2_ Place Dial Control Valve to desired seeing. Open in-fine valves and re-start pump per manulacturees instructions. GENERAL INK...ellATION: Turn Dial Control Valve to OFF when vaeUumlna,.backwash- ing,, or adding D.E. to litter, and when adding any other chemical In concentrated loan Never use PeItt_leurrl type lubricants on cover 0-ring. II lubrication becornesnecessary, use non-petroleum based lubricantS Such as Jades No. 327 tube or Ivory® bar soap Flush lank once a week by opening Dial Control Valve to full. Run for approximately 1 minute. Reset Dial Control Valve to desired setting Close feeder Dial Control Valve when vacuuming, loackwashing or adding D E to filter, and when adding other chemicals lo your pool. WINTERIZING: Where freezing temperatures can be expected, drain all water from feeder. Carefully remove any undisaolved damp trI•chior or bromine tablets or sticks. Rinse out chemical feeder thoroughly with water. Replace Cover and engage 1- 1 /2 turns Keep unit covered all winter to prevent entrance or rain or snow . PRESSURE - PRESSURE INSTALLATION This uses system pressure differential to divert water Cntatic-at feeder IrWithe fetunf-to-riooT piping after the filter/heater. The inlet of the chemical feeder is connected to the discharge side of the pump (before the tiler) andihe outlet is connected afterthefilter (and heater if installed). This creates a pressure-pressure piping Circuit through the feeder. If a heater is installed, a check valve must be installed between the healer outlet and the chemical feeder return This will prevent a high concentra- tion of the sanitizing agent from back flowing into the heater. This back flow can occu r rom a pressure d Amu- tat when the pump is shut off. If a high concentration of sanitizer flows Into the healer, it will cause the copper heal exchanger to deteriorate and possibly leak It this hap- ;WS, a fire or explosion may result causing property damage, personal injury or death. PRESSURE - SUCTION INSTALLATION With this method. the inlet pipe of the chemical feeder is conneeled to the discharge side of the pump (before the filter); and the outlet Is connected hack to the suction side ol the pump (before the pump). This creates a pressu re- suction piping circuit through the feeder. Do not use this Installation method II a heater Is Installed In the System. This method of installation allows too high of concentration of sanitizer to pass through the system than is safe for the copper heal exchanger of a heater, This installation may Cause Me heal exchanger to dew (Orate and possibly leak It this happens, a lire or explo- elan rnnv !AVM tausintin(0Periv darnage, Personal lniurY