Laserfiche WebLink
❑ M T E C CLD SERIES USERS GUIDE <br /> Advenced Tank Mml:to ng&LeakDetec#ion PORTABLE CONTAINMENT SUMP TESTER <br /> V. PROGRAMMING THE CLD KIT AND SETUP OVERVIEW <br /> The OEL8000111-CLD can store tests within the onboard <br /> microSD card.The completed test reports are accessible <br /> using the included web interface,accessed through the <br /> included RJ-45 port.To prevent possible data loss,you <br /> should download the test reports frequently. <br /> 1.Program Location Information: <br /> Using the 7"touch-screen display,from the CONTAINMENT <br /> LEAK DETECTION screen press the CLD TEST SETUP button <br /> (ORANGE;Figure 4.0). lia <br /> Enter the security code(default is"000000"),then press <br /> ENTER. Figure 4.0 <br /> a. Input details in the REPORT HEADER fields on lines 1-4 <br /> (RED;Figure 5.0). <br /> b. Touch the field you wish to change and use the on- <br /> screen keyboard to configure that line.Press SAVE. L_ -1 <br /> c. Repeat for lines 2,3,and 4 as needed. <br /> d. This information should be changed prior to testing a +.�.. _ . p <br /> new site.Clear and replace the old site information, <br /> IC <br /> replace with the current site info,and SAVE. ,�. _ .M.+ ++..� IC= <br /> Figure 5.0 <br /> 2.Program each MTG-probe(Enable or Disable probes): <br /> a. Fill in the SUMP LABELS(GREEN;Figure 5.0)for Sump 1(e.g.,"Regular Sump"or"Dispenser 1"). <br /> b. Touch the label field to be changed and use the on-screen keyboard to configure that line. Press SAVE. <br /> c. Repeat for each available probe. <br /> d. This information should be changed prior to testing additional sumps. <br /> e. Enable probes( ; Figure 5.0). By default,each probe is listed as disabled (red-colored buttons).Press <br /> to toggle button to enable(green-colored buttons). <br /> f. Disable probes by pressing their green ENABLED button. <br /> g. Measure the testing liquid(water)height in inches(for instance,a stick reading).Enter that value under <br /> TEST HEIGHT(BLUE;Figure 5.0)for each sump. <br /> h. Wait for the TEST HEIGHT value to stabilize in the programming. If the height does not change,ensure the <br /> probes are connected properly. <br /> 3.Program TEST TIME and TEST RATE(PURPLE; Figure 5.0). <br /> If you are unsure of the allowable values of the specific location for your site,please consult your local codes <br /> a. Enter in your TEST TIME;this is the duration of the test.(Default is 15 minutes). <br /> b. Enter in your TEST RATE;this is the maximum or allowable change in height during the TEST TIME. Default <br /> value.002,based on 15 minutes,is displayed. <br /> Other values:RP1200(60 minutes/0.125"),0.125"=1/8",0.002"=1/512" <br /> 4.Confirm all MTG-probes are responding properly: <br /> a. From the CLD TEST SETUP screen,verify all entries are correct and that the TEST HEIGHT matches the <br /> measured height of testing fluid(water). <br /> b. If the values are not correct,verify all connections and wires are secure and show no signs of damage. <br /> C. Press the EXIT SETUP button(WHITE;Figure 5.0).The CLD tester will ask you to wait while it saves the <br /> parameters during a brief reboot. <br /> OMNTEC Mfg.,Inc.,2420 Pond Road,Ronkonkoma,NV 11779 <br /> Phone(631)981-2001 Fax(631)981-2007 www.OMNTEC.com <br /> File Name:500165 rev2118.docx Page 6 of 8 Rev Date:3-11-2021 <br />