Laserfiche WebLink
OMTEC <br />CLD SERIES USERS GUIDE <br />A&oncedTank Monitoring&Leak Detoc ion PORTABLE CONTAINMENT SUMP TESTER <br />V. PROGRAMMING THE CLD KIT AND SETUP OVERVIEW <br />The OEL8000111-CLD can store tests within the onboard <br />microSD card. The completed test reports are accessible <br />using the included web interface, accessed through the <br />included RJ-45 port. To prevent possible data loss, you <br />should download the test reports frequently. <br />1. Program Location Information: <br />Using the 7" touch -screen display, from the CONTAINMENT <br />LEAK DETECTION screen press the CLD TEST SETUP button <br />(ORANGE; Figure 4.0). <br />Enter the security code (default is "000000"), then press <br />ENTER. <br />a. Input details in the REPORT HEADER fields on lines 1-4 <br />(RED; Figure 5.0). <br />b. Touch the field you wish to change and use the on- <br />screen keyboard to configure that line. Press SAVE. <br />c. Repeat for lines 2, 3, and 4 as needed. <br />d. This information should be changed prior to testing a <br />new site. Clear and replace the old site information, <br />replace with the current site info, and SAVE. <br />Y L <br />r.r• <br />i.,r rM1 r.i� k <br />_ Ia <br />Figure 4.0 <br />Figure 5.0 <br />2. Program each MTG-probe (Enable or Disable probes): <br />a. Fill in the SUMP LABELS (GREEN; Figure 5.0) for Sump 1 (e.g., "Regular Sump" or "Dispenser 1"). <br />b. Touch the label field to be changed and use the on -screen keyboard to configure that line. Press SAVE. <br />c. Repeat for each available probe. <br />d. This information should be changed prior to testing additional sumps. <br />e. Enable probes ( ; Figure 5.0). By default, each probe is listed as disabled (red -colored buttons). Press <br />to toggle button to enable (green -colored buttons). <br />f. Disable probes by pressing their green ENABLED button. <br />g. Measure the testing liquid (water) height in inches (for instance, a stick reading). Enter that value under <br />TEST HEIGHT (BLUE; Figure 5.0) for each sump. <br />h. Wait for the TEST HEIGHT value to stabilize in the programming. If the height does not change, ensure the <br />probes are connected properly. <br />3. Program TEST TIME and TEST RATE (PURPLE; Figure 5.0). <br />If you are unsure of the allowable values of the specific location for your site, please consult your local codes <br />a. Enter in your TEST TIME; this is the duration of the test. (Default is 15 minutes). <br />b. Enter in your TEST RATE; this is the maximum or allowable change in height during the TEST TIME. Default <br />value .002, based on 15 minutes, is displayed. <br />Other values: RP1200 (60 minutes / 0.125"), 0.125" = 1/8", 0.002" = 1/512" <br />4. Confirm all MTG-probes are responding properly: <br />a. From the CLD TEST SETUP screen, verify all entries are correct and that the TEST HEIGHT matches the <br />measured height of testing fluid (water). <br />b. If the values are not correct, verify all connections and wires are secure and show no signs of damage. <br />C. Press the EXIT SETUP button (WHITE; Figure 5.0). The CLD tester will ask you to wait while it saves the <br />parameters during a brief reboot. <br />OMNTEC Mfg., Inc., 2420 Pond Road, Ronkonkoma, NV 11779 <br />Phone (631) 981-2001 Fax (631) 981-2007 www.OMNTEC.com <br />File Name: 500165 rev2118.docx Page 6 of 8 Rev Date: 3-11-2021 <br />