SU-2601438_SSNL - Laserfiche WebLink

Home Browse Search

AINSTALLATION AND MAINTENANCE INSTRUCTIONS What you may need to install the Filtrol Package Contents • crew DriverStud Finder ,- ';",- . fffiffirl 2-#14 pan head screws or • Plumber's Putty 1. Filter Canister 1 _ 0- 2- 1.4" lag bolts with washers . Teflon Tape 2. Canister Lid 1 • 12"x 18" piece of plywood & 3. O-Ring(assembled on canister) 1 2 wood screws 4. Mounting Bracket with 2 Lid Clips 1 I • Drill, concrete bit and wrench, 5. Reusable Filter Bag-inside canister 1 if installing on concrete wall. 6. 1"I.O.Rubber Hose-5 feet 1 STEP-BY-STEP INSTALLATION INSTRUCTIONS 7• Hose Clamps 2 O 8. Elbow Inlet Barb Fitting- 1 STEP 1: Install the mounting bracket(figure 1). 1"threaded x 1"barbed Mounting location should be directly above standpipe, 9. Elbow Inlet Barb Fitting- ., O wallbox or laundry tub (figure 2). The 1"threaded x3/4"barbed 1 height should not exceed 72"from the floor and 10. Straight Outlet Barb Fitting- the drainhose should be at no more than a 45 ° angle 3/4"threaded x 1"barbed O Q leading to the drain location. Manual(not pictured) 1 Tube of Lubricant with Instructions 1 Figure 1 DRYWALL INSTALLATION- (not pictured) Locate wall stud; if you cannot STEP 2: Remove lid from canister; see additional instructions A�i install the bracket on a wallon opening canister(figures 3&4); stud, use a piece of plywood remove parts bag. and pre- install the bracket onto the plywood. Use a torpedo STEP 3: Install elbow inlet barb fitting onto canister rIl level to level the top of the lid. Screw fitting into top of lid,be careful to not over t'I bracket, then mark the holes tighten, hand tightening is best. It is normal if there I with a pencil for correct location. is still threading visible. Install the bracket with expander bolts STEP 4: Install straight outlet barb fitting onto the bottom of the canister. Be careful not to over tighten, hand tightening is or wood screws. best. Attach the drain hose provided onto the fitting, secure CONCRETE WALL INSTALLAITON -Use a with one of the hose clamps provided. Place canister into torpedo level to level the top of the bracket, then bracket: make sure the drain hose is straight down into drain mark the holes with a pencil for correct location. location. If that is not possible make sure the drain hose is at Use a concrete bit to pre-drill holes: install inserts no more then a 45' angle, as it may not drain correctly. For or use concrete anchor bolts to install the bracket. those inserting their drain hose into a wall box or standpipe, it is suggested to only have"6-12"of hose within the drain line. I NOTE.- The filter canister can get heavy as water STEP 5: Place filter bag into the canister. The plastic ring of passes through it, so the installed bracket needs to the filter bag sits on the rim on the canister, with the filter bag be sturdy. going down into the canister. Figure 2 STEP 6: Install the lid onto the canister; clamp down lid with the lid clips that are installed on the bracket. The clamps hold the lid in place and also holds the canister tight in the bracket. ® STEP 7:Attach your washing machines existing drain hose ® ® to the fitting on top of the lid and secure with one of the provided hose clamps.Tip: Using a hair dryer to soften the i end of the hose may provide ease getting it onto the fitting and a better seal in some applications. See troubleshooting section if your washing machine drain hose does not fit the provided fittings. Standpipe Wall Box Laundry Sink STEP 8:Turn washing machine on and run through a spin Examples of typical installations. However,because all cycle to check all connections are secure and there is no laundry rooms are not the same,you may need to modify your leaking. set up. See different installation examples on our site. The Filtrol has been tested and found to be compatible with all CAUTION.Always unplug washing machine before moving it or preforming any types of residential washing machines. type of service.Also,if your washing machine leaves clothing excessively wet after the final spin cycle,clean or replace the filter bag immediately