COMPLIANCE INFO_2010 - 2011 - Laserfiche WebLink

Home Browse Search

Bonded Double -Wall .ump Entry/Termination Fi._ing 5. Place one ring over the sump fit- ting in the inside of the sump and rotate to the desired angle. Make alignment mark on both the sump wall and the ring. 6. Mix one 7014 or 8014 adhesive for each fitting per the instructions in the adhesive kit. Mix in filler to thicken adhesive (fiberglass alignment rings will not seal properly without filler). 7. Apply adhesive generously, appro- ximately 1/w, thick to the inside and the outside of the sump walls where the alignment rings are located. Coat cut edges of the entry hole. Apply a thin coating of adhesive to the bonding surfaces of the alignment rings. 8. Line up rings with alignment marks and press together firmly. 9. Slide the metal retaining ring over inside section of sump fitting against the alignment rings until they are tight against sump wall. (A short section of 4" pipe may be used to drive the metal retaining ring over the fitting.) Be sure there is an adhesive bead visible between the rings and the sump wall. The metal ring must hold the assembly in position while the adhesive cures. If the assembly is not tight against the sump wail, firmly press the entry fitting against the outside sump wall while pressing the metal ring against the alignment ring on the inside. 10. Do not disturb assembly until the adhesive is cured. This includes bond- ing of pipe to the entry fitting and install- ing the threaded outlet fitting. Clean r The 1H' threads are a'modified NPT" , the Insemon of a standard spec male thread is menimizod. • SmUi Fibo oast 7U14 a 8014 adhostw Is rt ao tided TTr. 114" female threads are filoorglass and cannot be tightened the sant: as a metallic inroad. Tighten to 40 et -lbs or 1.5.2 turns • After installing a 114" NPT tilting, the passa9ow0y to 8w piping interstitial space should be cleared with air pressure to Insure that it is free of thread sealant and/or adhesive. excess adhesive from all bonding sur- faces. See adhesive kit instructions for cure times. 11. The use of an industrial hot air gun may speed up the curing process. Do not overheat. 12. Remove '/4" plastic threaded out- let protector. Apply adhesive to the '/4" fitting and screw into the 'W' threaded outlet. Tighten to 40 in. -lbs. or 11/2-2 turns past hand tight. After installing fitting, be sure the interstitial space is free from excess adhesive. Install a short hose and blow excess adhesive through the air passage. 13. Connect only flexible tubing or hos- es to the '/4" side outlet. NOTE: Tubing or hoses must be rated to full vacuum. TERMINATION EXAMPLE using SUMP ENTRYrrERMINATION FITTINGS Primary pipe Spigot NETRed Thread IIAS Concentric Reducer C' O 771 ----------- 0 \ 0 I ` Sump Entry! Containment pipe Rod Thread IIA ! Talrmewuon Fldeig Use concentric reducer to connect the sump entryhermination fitting to secondary containment pipe; DO NOT USE clamshell termination fittings with this style fitting. It is the policy of Fiber Glass Systems to improve its products continually. In accordance with that policy, the right is reserved to make changes in specifications, descriptions, and illustrative material contained in this bulletin as conditions warrant. Always cross-reference the bulletin date with the most current version listed at http:flwww.fgspipe.com. The information contained herein is general in nature and is not intended to express any warranty of any type whatsoever, nor shall any be implied. MEMBER ISO 9001 Vii rOtuIPMt NI INS, 4 FIBER GLASS SYSTEMS 0 Trademark of Varco UP, Inc. FIBER GLASS SYSTEMS • A NATIONAL OILWELL VARCO COMPANY wvvw.smithfibercast.com 2700 W. 65th ST, LITTLE ROCK, AR 72209.501-568-4010 • FAX 501-56"465 Printed U.S.A. 1M1007 25 S MAIN ST., SAND SPRINGS, OK 74063.918-245-6651 • FAX 918-245-7566