INSTALL 1999 - Laserfiche WebLink

Home Browse Search

• Installation of Model SB00 l L C is detailed in this sec- Power circuit wiring (contractor provided) enters the left tion and Figure B (see page 30). Reference Figure C, conduit at the bottom of the control panel and is con - (see page 30) for Model SBOO 14C circuit diagram. nected to terminals LI and L2. Model S13001IC Shown o Power Gran se Gaal (To 120 Vous AC) To Ground Coma (To S.roor Asttembty) swdatc.« c Power ChaoAutor„atK TeWplom Vote; 120 VoAC) ftone Dater Model SBOO14C1 and SB0014C4 Hbmw LQN w� t.yea o est sub - o ©ted ,uabie N.,e, v � lo+ v.ttaq. H-0 VW" (ke--V sate) C0,0A Hubs Cmdw Hub D1. Location H`b V0UW (tt.t .Y sate) Cdrbue MM Cmtdn Hub AWARNING Locate Control Panel in a Non- Haz- ardous Area Where an Explosive Environment Will Never Exist. • Control panel can be wall mounted using the provided mounting hardware. D2. Power Circuit • All wiring must be in accordance with local codes • Control panel is pre -assembled and ready to wire. ❑ A 120 volt AC power source is required. Model SBOOI I Shown _r.---- — — J 0: -� r t ,- �y Power Circuit _11 I Ground (To 120 Volts AC) To Ground lug • Circuit breaker (contractor provided) common to other devices is recommended. ❑ This increases probability tank owner will be aware of a tripped circuit breaker. • If there is no power to the control panel, the alarm bell and other warning devices cannot be activated. • In areas where extreme line transients occur, additional surge protection should be installed on incoming supply source. D3. Sensor Circuit • Pre -assembled reservoir sensor is ready to wire (con- tractor supplied) to the control panel. ❑ For intrinsically safe wiring, use 16 AWG or 14 AWG type THHN or type MTW (contractor supplied) for Model SB control panels and SP switch panels. ❑ For UL rated applications, the maximum wiring dis- tance between the sensor and control panel is 900 feet. • Wiring for sensor circuit enters right conduit at bottom of control panel and is connected to terminals S 1 and G 1. Model SB0011C1 and SB0011C4 0 N.'" t.qt• warm Be* y� rest awa. wmt L— 1-.w Hqb v..W (uMnnsca.V sate) Cond.t Huts -begat Hub 0. twnw 1,qm 0 t,•t. Aiarm B.4 AYrrn Test a: v L L— V." Cmau (imm.sr�ry Sale) Cor4A Hub • On four circuit control panel (Model SB0014C) there are four terminal pairs. • Connect a separate sensor to each terminal pair ❑ S1, GI ❑ S3, G3 ❑ S2, G2 ❑ S4, G4 Important: On the four circuit control panel, if less than four monitoring circuits are used, a jumper wire is re- quired to separately connect each unused terminal pair. D4. Optional Wiring Device Circuit in • Tank owner may specify additional warning devices to be provided by contractor. ❑ Optional warning device circuits enter panel at the center conduit. 0 O awm BM T- Uarm O B« H`b V0UW (tt.t .Y sate) Cdrbue MM Cmtdn Hub AWARNING Locate Control Panel in a Non- Haz- ardous Area Where an Explosive Environment Will Never Exist. • Control panel can be wall mounted using the provided mounting hardware. D2. Power Circuit • All wiring must be in accordance with local codes • Control panel is pre -assembled and ready to wire. ❑ A 120 volt AC power source is required. Model SBOOI I Shown _r.---- — — J 0: -� r t ,- �y Power Circuit _11 I Ground (To 120 Volts AC) To Ground lug • Circuit breaker (contractor provided) common to other devices is recommended. ❑ This increases probability tank owner will be aware of a tripped circuit breaker. • If there is no power to the control panel, the alarm bell and other warning devices cannot be activated. • In areas where extreme line transients occur, additional surge protection should be installed on incoming supply source. D3. Sensor Circuit • Pre -assembled reservoir sensor is ready to wire (con- tractor supplied) to the control panel. ❑ For intrinsically safe wiring, use 16 AWG or 14 AWG type THHN or type MTW (contractor supplied) for Model SB control panels and SP switch panels. ❑ For UL rated applications, the maximum wiring dis- tance between the sensor and control panel is 900 feet. • Wiring for sensor circuit enters right conduit at bottom of control panel and is connected to terminals S 1 and G 1. Model SB0011C1 and SB0011C4 0 N.'" t.qt• warm Be* y� rest awa. wmt L— 1-.w Hqb v..W (uMnnsca.V sate) Cond.t Huts -begat Hub 0. twnw 1,qm 0 t,•t. Aiarm B.4 AYrrn Test a: v L L— V." Cmau (imm.sr�ry Sale) Cor4A Hub • On four circuit control panel (Model SB0014C) there are four terminal pairs. • Connect a separate sensor to each terminal pair ❑ S1, GI ❑ S3, G3 ❑ S2, G2 ❑ S4, G4 Important: On the four circuit control panel, if less than four monitoring circuits are used, a jumper wire is re- quired to separately connect each unused terminal pair. D4. Optional Wiring Device Circuit in • Tank owner may specify additional warning devices to be provided by contractor. ❑ Optional warning device circuits enter panel at the center conduit.