INSTALL_2008 - Laserfiche WebLink

Home Browse Search

Veeder-Root Line Leak Axation Guide • 5. Verify that the Rotary Pressure Dial, also on the CPT's Controller CPU board, is set to either the 2 (24 psi), 3 (27 psi), 4 (30 psi), 5 (33 psi), or 6 (36 psi) position, Element Red Jacket Standard CPT 'LLD ransducer n SwiftCheck lalve Transducer Installation - Red Jacket Big -Flo and Maxxum Pumps BIG-FLO PUMPS t. You will need to install a reducing tee (customer supplied) in either of the 3 -inch discharge ports of the pump with the 2 - inch opening facing up. If you have the room, it may be easier to install this tee between the Pressurstat kit and the unused port instead of in the discharge line (as shown in the fsgure below). Alternativeiy, the PLLD transducer can be installed in the leak detector port of a Big -Flo leak detector if it is already present in the line (as shown in the figure below). 2. Install the Red Jacket Big -Flo Pressurstat Kit (Red Jacket part number 144-314-5) following the instructions with the kit. 3. Thread the PLLD transducer into the 2 -inch opening of the tee. IMPORTANT! Seal any pipe threads using a UL -classified, nontoxic pipe sealant suitable for the fuel involved. 4, Verify that the console has Version x19 or later software. OPTIONAL INSTALLATION EXAMPLE 314" NPT Union, a 314"NPT nipples, PLLD transducer P reducing nipple (customer supplied) 3" discharge line (to dispensers) 4 1 Red Jacket Big -Flo Red Jacket Big -Flo Pressurstat kit - Pressurstat kit- 2"x 2"x 3" reducing tee PIN 144-314-5 PIN 144-314-5 and 3" NPT nipple (customer supplied) (customer supplied) (customer supplied) i 12 Junction box (customer supplied) kl -off, epoxy seal per NFPA c (customer supplied) conduit to console (customer supplied) D transducer in 2" port of Flo Leak Detector (customer plied) "x 3" 90 degree elbow (customer supplied) 3' discharge line (to dispensers) 'pIlJ.hglb9,o,p 01 �y a. • � . >r� r �� SII ■, it ■ �'I,I�■�■�a: liter s Transducer Installation - Red Jacket Big -Flo and Maxxum Pumps BIG-FLO PUMPS t. You will need to install a reducing tee (customer supplied) in either of the 3 -inch discharge ports of the pump with the 2 - inch opening facing up. If you have the room, it may be easier to install this tee between the Pressurstat kit and the unused port instead of in the discharge line (as shown in the fsgure below). Alternativeiy, the PLLD transducer can be installed in the leak detector port of a Big -Flo leak detector if it is already present in the line (as shown in the figure below). 2. Install the Red Jacket Big -Flo Pressurstat Kit (Red Jacket part number 144-314-5) following the instructions with the kit. 3. Thread the PLLD transducer into the 2 -inch opening of the tee. IMPORTANT! Seal any pipe threads using a UL -classified, nontoxic pipe sealant suitable for the fuel involved. 4, Verify that the console has Version x19 or later software. OPTIONAL INSTALLATION EXAMPLE 314" NPT Union, a 314"NPT nipples, PLLD transducer P reducing nipple (customer supplied) 3" discharge line (to dispensers) 4 1 Red Jacket Big -Flo Red Jacket Big -Flo Pressurstat kit - Pressurstat kit- 2"x 2"x 3" reducing tee PIN 144-314-5 PIN 144-314-5 and 3" NPT nipple (customer supplied) (customer supplied) (customer supplied) i 12 Junction box (customer supplied) kl -off, epoxy seal per NFPA c (customer supplied) conduit to console (customer supplied) D transducer in 2" port of Flo Leak Detector (customer plied) "x 3" 90 degree elbow (customer supplied) 3' discharge line (to dispensers) 'pIlJ.hglb9,o,p