|
PURPOSE
<br />1.1 THE PURPOSE OF THESE INSTRUCTIONS IS TO ACQUAINT YOU WITH SOME OF
<br />THE GENERAL RULES AND REGULATIONS PERTAINING TO YOUR WORK AT SHELL'S
<br />RETAIL FACILITY. YOUR COMPLIANCE WITH THESE REGULATIONS IS MANDATORY.
<br />ADDITIONAL SAFETY PROCEDURES MAY BE NECESSARY. THESE INSTRUCTIONS ARE
<br />ONLY A MINIMUM REQUIREMENT AND SHALL NOT BE CONSTRUED AS COMPLETE OR
<br />COMPREHENSIVE. IT IS THE DIRECT RESPONSIBILITY OF THE CONTRACTOR,
<br />FABRICATOR OR BOTH TO INSURE THAT THEIR EMPLOYEES HAVE A SAFE WORK PLACE
<br />AND ARE PERFORMING THEIR WORK SAFELY, INCLUDING SHELL'S EXISTING FACILITY
<br />PERSONNEL AND CUSTOMERS. IF STATION IS OPERATING, DEALER AND CONTRACTOR
<br />MUST EXCHANGE "HAZCON" INFORMATION, PER OSHA 1910.1200.
<br />CONTRACTOR /FABRICA ]'_OR
<br />2.1 THE TERM "CONTRACTOR" OR "FABRICATOR" AS USED IN THESE INSTRUCTIONS
<br />SHALL BE UNDERSTOOD TO INCLUDE THE CONTRACTOR, FABRICATOR, THEIR WORKERS
<br />AND ANY SUBCONTRACTORS AND THEIR WORKERS PERFORMING WORK UNDER THE TERMS OF
<br />THE CONTRACT UNDER CONSIDERATION. CONTRACTOR, FABRICATOR IS RESPONSIBLE
<br />FOR ITS WORKERS AND SUBCONTRACTORS AND FOR DIRECTING AND SUPERVISING
<br />THEIR WORK.
<br />COMPANY
<br />3.1 THE TERM "COMPANY REPRESENTATIVE" USED IN THESE GUIDELINES SHALL BE
<br />ANY ENGINEER, CONSTRUCTION & MAINTENANCE REPRESENTATIVE, OR MAINTENANCE
<br />PERSON DESIGNATED BY SHELL OIL COMPANY.
<br />GENERAL
<br />4.1 SAFETY REGULATIONS OF SHELL OIL COMPANY MUST BE FOLLOWED AT ALL
<br />TIMES. COMPANY REPRESENTATIVES WILL HAVE COMPLETE AUTHORITY TO STOP WORK
<br />IF ANY VIOLATION OF THE SAFETY GUIDELINES IS RECOGNIZED.
<br />4.2 CONTRACTOR, FABRICATOR OR BOTH SHALL MAINTAIN WORK SITE IN AN
<br />ORDERLY MANNER DURING CONSTRUCTION. SITE SHALL BE LEFT IN A CLEAN, NEAT,
<br />ORDERLY AND SAFE CONDITION UPON COMPLETION OF EACH WORK DAY.
<br />4.3 CONTRACTOR, FABRICATOR OR BOTH SHALL PROVIDE HIS MEN WITH PROPER
<br />SAFETY EQUIPMENT SUCH AS GOGGLES, EAR PLUGS, PROTECTIVE CLOTHING, ETC.
<br />AND INSURE THAT EQUIPMENT IS USED PROPERLY.
<br />44 HARD HATS SHALL BE WORN WHILE ANY OVERHEAD WORK IS TAKING PLACE (NO EXCEPTIONS).
<br />4.5 BARRICADES, FLAGS, STEEL PLATES OVER TRENCHING, INCLUDING PROPER SLOPING AND
<br />SHORING OF TRENCH WALLS, PROVIDED BY CONTRACTOR OR FABRICATOR AS NECESSARY TO
<br />SAFELY SECURE SITE AND PROTECT ALL VEHICULAR AND PEDESTRIAN TRAFFIC ON
<br />AND NEAR JOB SITE.
<br />4.6 CONTRACTOR, FABRICATOR SHALL PROTECT ADJOINING PROPERTY, EARTHWORK,
<br />TREES, ETC., FROM DAMAGE AND GIVE PROPER WRITTEN NOTICE OF PROPOSED WORK
<br />TO ADJOINING PROPERTY OWNERS. DAMAGE TO ADJOINING PROPERTIES BY
<br />CONTRACTOR'S OR FABRICATOR'S ACTIVITIES SHALL BE REPAIRED AT THE
<br />CONTRACTOR'S OR FABRICATOR'S EXPENSE,
<br />4.7 CONTRACTOR, FABRICATOR SHALL PROVIDE ALL NECESSARY FIRST—AID,
<br />AMBULANCE, AND HOSPITAL SERVICES, IN CASE OF INJURY TO CONTRACTOR'S, OR
<br />FABRICATOR'S EMPLOYEES ON SHELL PREMISES.
<br />4.8 SHELL REPRESENTATIVE WILL NOTIFY DEALER OR STATION MANAGER (24)
<br />HOURS PRIOR TO CONTRACTOR, FABRICATOR COMMENCING ANY MINOR MAINTENANCE
<br />WORK. DEALER OR STATION MANAGER WILL BE NOTIFIED A MINIMUM OF (3) DAYS
<br />PRIOR TO CONTRACTOR, FABRICATOR COMMENCING ANY MAJOR MAINTENANCE WORK.
<br />4.9 CONTRACTOR, FABRICATOR SHALL NOT USE SHELL'S OR DEALER'S TOOLS, OR EQUIPMENT,
<br />4,10 CONTRACTOR, FABRICATOR SHALL HAVE A 20# BC FIRE EXTINGUISHER READILY
<br />AVAILABLE FOR ANY WORK WHICH INVOLVES RELEASE OF PRODUCT OR USE OF A
<br />SPARKING DEVICE.
<br />4.11 NO SMOKING IS ALLOWED WITHIN TWENTY—FIVE FEET OF AREA WHERE PRODUCT
<br />IS BEING DISPENSED OR RELEASED OR WHENEVER GASOLINE VAPORS ARE PRESENT.
<br />DEALER HAS AUTHORITY TO PROHIBIT SMOKING ON ITS FACILITY.
<br />4,12 ALL CONTRACTOR'S, FABRICATOR'S EQUIPMENT IS SUBJECT TO INSPECTION BY
<br />COMPANY REPRESENTATIVE. EQUIPMENT WHICH THE COMPANY REPRESENTATIVE
<br />CONSIDERS HAZARDOUS TO PERSONNEL OR FACILITIES MUST BE SHUT DOWN AND/OR
<br />REMOVED FROM THE PREMISES IMMEDIATELY. EQUIPMENT SHALL BE KEPT AT LEAST
<br />(25) FOOT RADIUS AWAY FROM ANY OPERATIONAL GASOLINE DISPENSING AREA.
<br />n k,
<br />SAFETY GUDELINES
<br />ACC
<br />FIRE CONTROL.
<br />5.1 IN CASE OF FIRE, THE FOLLOWING GENERAL PROCEDURE MAY BE USED:
<br />NOTICE: CONTRACTOR, FABRICATOR SHOULD CONSIDER THE SPECIFIC SITUATION
<br />BEFORE ACTING.
<br />•
<br />TURN OFF
<br />EMERGENCY
<br />DISCONNECT
<br />SWITCH OR MAIN BREAKER.
<br />•
<br />CONTACT
<br />LOCAL FIRE
<br />AND POLICE
<br />DEPARTMENTS.
<br />• EVACUATE AREA IMMEDIATELY.
<br />• ATTEMPT TO EXTINGUISH ONLY SMALL FIRES OR KEEP IT FROM SPREADING TO
<br />ADJACENT AREAS, IF FIRE IS OUT OF CONTROL, LEAVE THE AREA TO AVOID
<br />RISK OF INJURY. NOTICE: USE DRY CHEMICAL FIRE EXTINGUISHER BC TYPE
<br />TO COMBAT SMALL GASOLINE FIRES.
<br />• FUELING OF RUNNING EQUIPMENT IS NOT ALLOWED.
<br />WELDING
<br />6.1 WARNING — CONTRACTOR, FABRICATOR KEEP ALERT TO POTENTIAL HAZARDS IN
<br />THE WORK ENVIRONMENT. YOU ARE SUBJECT TO THE PRESENCE OF HIGHLY COMBUSTIDLE
<br />MATERIALS.
<br />6.2 CONTRACTOR, FABRICATOR SHALL BE RESPONSIBLE FOR FURNISHING HIS OWN
<br />EQUIPMENT AND PERSONNEL FOR TESTING THE WORK AREA TO INSURE SAFE
<br />CONDITIONS PRIOR TO AND CONTINUOUSLY DURING.ANY WELDING WORK.
<br />6.3 CONTRACTOR, FABRICATOR SHALL PROVIDE LOCKS TO SECURE ALL DISPENSERS
<br />WITHIN (25) FEET RADIUS OF WELDING AREA, NO PRODUCT MAY BE DISPENSED
<br />WITHIN A (25) FOOT RADIUS WHILE WELDING IS' TAKING PLACE.
<br />6.4 CONTRACTOR SHALL PROVIDE A STANDBY FIRE WATCH PERSON WITH A 20#
<br />BC FIRE EXTINGUISHER NEAR WORK VICINITY DURING ENTIRE WELDING JOB,
<br />6.5 ALL WELDING WORK SHOULD BE DONE IN CONTRACTOR'S, OR FABRICATOR'S
<br />SHOP OR AWAY FROM GASOLINE DISPENSING AREA IF AT ALL POSSIBLE,
<br />ELECTRICAL
<br />7.1 CONTRACTOR, FABRICATOR SHALL TURN OFF AND LOCK OUT OR DISCONNECT ALL
<br />ELECTRIC POWER AT PANEL BEFORE STARTING ANY ELECTRICAL WORK. TAG SWITCH
<br />TO INFORM STATION PERSONNEL AND/OR OTHER CONTRACTORS OF WORK IN PROGRESS
<br />TO AVOID ACCIDENTAL STARTUP OF POWER.
<br />7.2 AFTER DISABLING SYSTEM AND BEFORE STARTING WORK, CONTRACTOR, OR
<br />FABRICATOR SHALL TRY TO ACTIVATE EQUIPMENT ON THAT CIRCUIT TO INSURE
<br />CORRECT SYSTEM HAS BEEN LOCKED OUT,
<br />7.3 ELECTRIC PANEL SHALL BE RE—LABELLED TO REFLECT ANY WIRING CHANGES BY
<br />CONTRACTOR.
<br />7.4 ALL ELECTRIC WORK SHALL BE IN ACCORDANCE WITH THE LATEST NATIONAL
<br />ELECTRIC CODE,
<br />7.5 SPECIAL NOTE: USE ONLY "GFI" OR (3) PRONG PLUG AND SOCKET ELECTRICAL
<br />TROUBLE CHORDS. CHORDS MUST BE INSPECTED ROUTINELY WHILE ON
<br />JOB SITE TO ENSURE SAFE WORKING CONDITIONS.
<br />GENERAL EQUIPMENT
<br />8.1 ALL FIRE EXTINGUISHERS USED BY CONTRACTOR .SHALL HAVE AN ACCURATE—ANNUAL
<br />INSPECTION TAG AND SHALL NOT SHOW SIGNS`OF LOW PRESSURE CORROSION, DAMAGE, OR
<br />OTHER IMPAIRMENT WHICH WOULD AFFECT ITS PERFORMANCE.
<br />8.2 PRIOR TO WORK ON ANY ELECTRICAL POWERED EQUIPMENT, CONTRACTOR,
<br />FABRICATOR SHALL DISCONNECT OR TURN OFF ALL POWER, CONTRACTOR,
<br />FABRICATOR SHALL LOCK OUT AND TAG SWITCHES TO AVOID ACCIDENTAL STARTUPS.
<br />CONTRACTOR, FABRICATOR SHALL TEST EQUIPMENT TO INSURE ALL POWER HAS BEEN
<br />CUT OFF PRIOR TO START OF WORK.
<br />TAN CE (
<br />PREMISES (SHELL RETAIL EAC
<br />9.1 CONTRACTOR, FABRICATOR ACCEPTS THE PREMISES IN "AS IS" CONDITION,
<br />AND COMPANY MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AS TO THE CONDITION
<br />OF THE PREMISES INCLUDING, BUT NOT LIMITED TO, FITNESS FOR ANY PARTICULAR
<br />PURPOSE.
<br />REVISIONS
<br />APPROVALS
<br />SMELL AIL COMPANY
<br />AREA ENGINEERING MANAGER pp7E HOUSTON, TEXAS
<br />1*1
<br />DISTRICT MANAGER
<br />DISTRIBUTION MANAGER
<br />DATE
<br />Dhl'C
<br />CONSTRUCTION/DISTRICT ENGINEER DATE
<br />PLANS PREPARED BY:
<br />A & S ENGINEERING
<br />49 QUAIL COURT, SUITE 303
<br />WALNUT CREEK, CALIFORNIA 94596
<br />PHONE: 510-933-0578 FAX: 510--033-0588
<br />SAFETY GUIDEL.INF`
<br />?�IIW.T?1 NJAMIN {{ULT' ll IVE & ;N j ROTATE c)
<br />5T06K`r0W I CA11 FORMIA
<br />SCALE: DRAWING # DR -89024
<br />DAIE.: 7/18/94 WI..c#
<br />DWN. BY: SJR.'
<br />_CIIKD. BY: SHEET
<br />(O SHELL 011_ COMPANY, ALL RIGHTS RESF.'RVED 1991
<br />
|