COMPLIANCE INFO 2000 - 2004 - Laserfiche WebLink

Home Browse Search

Dec 04 00 09: 16a M ke Brown 20461 -6342 p. 2 _ REDJACKEr : - INSTALLATION INSTRUCTIONS FXV LEAK DETECTORS FXIV Part No. 116-056-5, F'X2V Part No. 116.057-5 FX1DV Part No. 116-058-5, FX2DV Port No. 116-059-5 - 'ibhW..nr Yes>.�..s.r6mrvV�W.tiia.nwmena.vrmuUrM+�d..r�ae MY M.4smm�.o.u�baaeea"miuM Wsl:Fd,sxvd¢�c - rd wspu4.nade.a�ewu�sm,et. ns.,.mwiasn. ® w riieA...'ubunmi m.wm demv.J n�e.w.u.rov.i i.dbra we•oa.ni'.LceM rA:dr can mu�ee.n Daec".iirvvr. �4sw.ewd;e.ay.oaum�".Wlso..r.pcetl.o.ormaiew � a..m,r.vYma.t w"ew Y..nsirpa.a. seem ,mpcaeart„r®,nie,.d mpwoei�aury natva..� Before installing leak detector,mt tew the application section in leak detector manual 06191 for limitatiooa or restrictions on usage- OEM=e This fastruotlou sheet should be kept with the and user of the leak detector for reference. When using 117-195 Big-Flo Die phragm Valve,refer to inetatletlon ina[ruceioae 0041-994 included with the valve. When using an FXV model leak detector with adapter housing #058.072.5, refer to installation iaetruedoae 8041415.1 lac]uded with the housing.M Leak Detector aro foe use with allUt-Listed 4-inch fad Jaokee modete containing a"P"or"AG"preftsu FE Petro U[4Listed 4-iaoh•STP^medals;Tokhaim UT- Listad 4-inch models—585A•34 and 585A•150. Tampering with the screws or seals oa this leak detector may inhibit operetta.and will void warranty. This Red Jacket leak detector is to be installed into the tine. 2. Remove the two-inch plug from the top of the Red inch threaded tapping on top of the Rad Jacket submer iWio Jacket pump. If the two-inch plug is found to be so pump.The M% models sire specially designed for use with tight that it cannot be removed, the submersible diesel fuel and should he used in diesel applications to provide should be removed from the tank and placed in a vise. the appropriate operating charactariatia.For proper installs- Remove the functional element assembly next to the tied,the following"tape should be followed in sequence: pipe plug. The plug should thea come out readily if a large pipe wrench is used. Replace functional ele- DO NOT wire submersible pumps to run meat assembly securely.and replace the pump in the continuously.Red Jacket line leak deter. tank.(See Step 9 before replacing pump). are will not perform leak tests on pumping 9. Examine straight bore below two-inch thread for systems that run continuously, corrosion roughness. If found a be rough,.smooch } with fine emery paper. Mill M ALL AIR MUST RE OUT OFTHE SYSTEM 4. Apply UT-classified non-toxic pipe thread sealant to FOR THE LF.A$ DL-MCPOR TO WORK the two-inch thread& on the detector. Lubricate PROPERLY.Befnmiastallingleakdete - 0-ring on the leak detector. toe in the pump, fill the system with S. Screw the leak detector into the pump. Tighten with product by running the pump and deliv. a wrench(top hex is 1-U4 in.). arias product from each dispenser 6. Installation ofve.t tube sad snap top connector. (startingwith the farthest from the pump For MV models and working to the pump) until all air is s. Remove 1/4•inehP Po iP 1ug from tank teat removed from system. portinthe Pecker(on6-inch Big-Flo applies- Certain regulatory bodies require that leak detector remain tions,remove the 1/4-inch pipe plug from the in the system after the lines have been installed.The lines may neer/flange assembly). be purged of air by back pressuring the lines with an inert gas b. Apply a UL-classified non-toric pipe thread such as helium or nitrogen to a pressure of 25 psi(172 kPa), sealant to the threads of the 1/4-inch NPT This may be done at the impact valve under the dispenser, straightvent tube fitting and install in tank Nhenthis pressure hasbeen reached,the leakdetecmrwill be test pact of the packer. On 6-inch Big-Flo in the open position. By turning on the pump and gradually applications,the 1/4-inch NPT straightvent bleeding the gaa from the lint through a valve at the impact tube fitting may be installed into the riser/ valve of the farthest dispenser,the line may be purged of air. flange assembly. C, Apply a ULclassified non-toxic pipe thread Disconnect power to the submersible sealant to the threads of the IA-inch NPT i1111tLi1� pump and relieve pressure before install- 90-degree vent tube fitting and install is the Ing or removing petroleum equipment. leak detector vent opening in the cap of the leak detector. 1. Disconnect power to pump at the load center Tag or d. Insall the vent tubing into both fittings and 1«k out the breaker to avoid the pump being turned tighten. on accidentally. 042.106.1 As,A 6196