INSTALL_2014 B100 - Laserfiche WebLink

Home Browse Search

applicable).Refer to dimension `D"in TABLE 8-1 or TABLE 8-2. =IIIII Position strap clip at tank top — Align(within a tolerance of±1 inch)all anchor points with the IIIII= C IIIII— marked arrowhead symbols►W on the tanks. —IIIII =1111 8.3.6. Use only appropriately sized hardware with the strap IIIII,— IIIII— eye.See FIGURE 8-3 for dimensions of strap eye. - illlll IIIII' ® CAUTION Oversized hardware may damage the strap eye and may result —IIIII R —IIIII in minor or moderate injury. IIIII=III IIIII- A —IIIII Galvanized Strap Eye D (side view) IIIII_ —I III Galvanized Strap Hook 3/8" =IIIII= 'I_i 12 Deadiman �°h IIIII —11111 (front view) IIIII'.-IIIII-IIIII=IIIII -IIIII =-IIIII= 31/4" 13/8.. FIGURE 8-2 + Anchoring Dimensions for FIGURE 8-2 Tank Dia. A B c D min. D max. FIGURE 8-3 4' 18" 12" 8'-41/4" 27" 30" 8.3.7.When connecting the end of an anchor strap to the 6' 23" 13" 12'-1" 42" 48" anchor point,common methods are those shown in FIGURE 8-4: a' 31' 15" 15'-1" 52" 58" A)using a drop-forged turnbuckle, B)using a looped wire rope,C)using a combination of both A and B,and D)using 10' 45" 15" 18'-83/4" 69" 75" the hook end of the strap. 12' 50" 23" 22'-6 3/4" 87" 93" TABLE 8-2 C - 8.3. HARDWARE AND ANCHOR POINTS 8.3.1.When Xerxes-supplied anchoring hardware is not being _ used,the installing contractor is responsible for providing hardware and anchor points of sufficient size and strength for B the tank being installed. A - 8.3.2.Anchoring hardware must be manufactured to industry standards and dimensions, and sized according to TABLE 8-3. Tank Minimum Turnbuckle Diameter Minimum D Diameter (by Type) Wire-Rope Hook Jaw Eye Diameter - 4' 314" 1/2" 1/2" 318" 6' 3/4" 1/2" 1/2" 318" 8' 11/4" 314" 314" 1/2" - 10' 1114" 314" 3l4" 112" 12' 1 114" 3/4" 314" 112" FIGURE 8-4 TABLE 8-3 8.3.8.If using a wire rope, refer to recommendations of wire- 8.3.2.1.All exposed metal on the anchoring system must be rope manufacturer and supplier,and follow accepted industry coated or galvanized to protect against corrosion. standards when selecting, using,attaching or connecting wire rope.See FIGURE 8-4,FIGURE 8-5 and FIGURE 8-6. - 8.3.3.The particular configuration of hardware will be determined by the contractor,the owner or the owner's representative. 8.3.8.1.The installer is responsible for using appropriate and - approved engineering practices when fastening wire rope. 8.3.4.If hardware being used is not provided by Xerxes,con- tact the hardware manufacturer or supplier for specific infor- 8.3.9.When fastening wire rope,use a minimum of 2 clips for a motion on hardware and its use. 3/8-inch wire rope and 3 clips fora 1/2-inch wire rope on each termination.See TABLE 8-3 for minimum wire-rope diameter. 8.3.5.Locate the anchor points as shown in FIGURE 8-1 or 8-2 (whichever is applicable)and TABLE 8-1 or 8-2(whichever is 8.3.10.Turn back from the thimble the exact amount of wire rope specified by the manufacturer of the clips used. 15