Laserfiche WebLink
• <br />r] <br />Stop il <br />Inslnll Ino adjustable Slabilisor Bar <br />Will to Ilia side struls of the <br />diapnnser sump. Do not install the <br />vnlvn plains at this time. <br />Slep 5 <br />4 <br />Inelnll the necossmy amount of <br />Shop 1 <br />3.� <br />Step 2 <br />wtn <br />bll Ilia allow valve mounting <br />to it tensa mounted shonr(rn <br />� 1i <br />W°or <br />!� \ <br />Aller the mounting plate hes been <br />connected to the shear valve, <br />pinto <br />I 9 p <br />Install Ilia necessary amount of <br />- <br />valve usnel the three not homled <br />!,. 1 ' <br />connect the riser pipe to the bottom <br />ennknl -,mews provided ncqulres <br />r' { �� <br />of the shear valve. <br />Il in Imr Na 114" Allen Wionch. <br />r n <br />�(� <br />Slop 9 <br />■ <br />phunbiuq cnnuoclion In511IC ilio <br />Stop il <br />Inslnll Ino adjustable Slabilisor Bar <br />Will to Ilia side struls of the <br />diapnnser sump. Do not install the <br />vnlvn plains at this time. <br />Slep 5 <br />4 <br />Inelnll the necossmy amount of <br />Jj -----_._-- <br />(24. <br />Conduit Fidry Boots into the <br />dosimd <br />r. <br />location on the side of the <br />dispenser sit mp. <br />/ <br />Step G <br />I 9 p <br />Install Ilia necessary amount of <br />I lexlhle Frilly Boots Into Ilia <br />dreiird lu[:ltiolls oil the side of Ilia <br />6 <br />tli•:pnrsr•l swop. <br />r n <br />�(� <br />Slop 9 <br />Conned the coupled piptnq to Ille <br />phunbiuq cnnuoclion In511IC ilio <br />I onielnser Sump, <br />Iloight Arljrl^hgllility <br />All dmix+nr,m •:unnr: aillrl a wide magc of heighl adjustability, it required. The <br />ensieea limn•: ul udiustinq the pipe entry height Is to Install the Flexible Entry <br />Btxt ni a higher envy Iavel. <br />It that procedure does not provide adequate entry <br />heighl, the riser si,chou can be cul down to Ilia desired height by disconnect- <br />ion Ilia h;mm necembly. <br />JI <br />�L <br />12" <br />Jj -----_._-- <br />(24. <br />L <br />Step 7 <br />Install the anchor bolts provided In <br />Ilia specific holes In the mounting <br />frame to accommodate the model <br />dispenser to be installed. <br />Step 8 <br />Install Ilia riser pipelshear valve <br />assembly to the stabilizer bar <br />inside Ilse dispenser sump. <br />Sump Access Boot <br />(Optional) <br />A 4" boot designed specifically to <br />seal sump access holes which are <br />drilled to allow for easier installation <br />Inside Ilia sump. <br />Step 3 <br />Install the elbow connection to the <br />threaded riser pipe. <br />Pipe Entry Locations <br />For standard pipe burial applications, the piping should enter at the lowest <br />possible entry point In Ilia sump. For determining the correct pipe entry loca- <br />llon for the dispenser model to be used, refer to the Pipe Entry Guide provid- <br />ed with each sump unit. Refer to the Flexible Entry Boor installation Insimc- <br />lions on the next page for proper installation of all pipe entries. <br />Delarge is a" to <br />fileWlermdius of 1 <br />Il:e Mal Illus 12', <br />j a �l. .• 1 _+te.... ...,-i �u <br />Center Lkle <br />Min Center <br />Entry Lble <br />