Laserfiche WebLink
B. \VIRING (cont'd) <br />IS AMP POLE <br />SWIICII <br />IN E C N[ <br />DISCONNECCTT UR MEANAIL WITES TO <br />_ <br />DCfPENSEf6n <br />PANE UMUND CONNECTION IN <br />ACCORDANCE WITH LOCAL CODES <br />0 <br />GREEN GROUNo1N0 <br />WREW <br />'GROUND WIRE <br />CUPWASHER <br />'TERMINAL <br />-FnERNAL TOOTH <br />LMM M14ER <br />-POWERLEADS <br />TO PUMPS <br />-CONDUIT SEALS <br />-CONDUITsox <br />PUMP <br />NNCTION <br />BOA .- <br />4. Suggested wlring diagram WIT ROUT optional control box. <br />Combination 012 pole dispenser switches orexternal pilot light. <br />• Rated for twice the full load current of the motor: <br />1/311P-Oamps, 3/411P-13amps,l.1/2HP-21amps <br />• Rated for handling locked rotor current of the motor: <br />1/311P-13 strips, 3/4f1P-22amps,1-1/2HP-42smps <br />10 <br />LOADCENTER <br />M OR 210 VOLT <br />t4a <br />W KLGYI AWIIIY„ <br />11Y:N uAAs <br />EMMM Proper check valves, with pressure relief, must be In- <br />stalled In the discharge line of each pump to prevent <br />product frons being pumpod Through the pressure relief <br />syslom ollheadJacent pumpwhon his notrunnhng.Chock <br />valves must be compatible Willi the product being <br />pumped. <br />PRESSURE RELIEF TYPE <br />Fig. 1 Dual submersible manifold Installation. <br />This diagram (Fig 2) shows the wiring allowing both submersibles to <br />operate simultaneously with any combinatlon of dispensers turned on. it,'... <br />To operate Individually, the appropriate toggle switch, located externally <br />on the aide of the control box must be turned off manually. The check <br />valves and 220/240 volt relay are not available from Red Jacket and <br />should be purchased locally. <br />s1o«� o"rt ""ro <br />pmlW iuul Uncles 1@v. RELAY I I <br />ALLEN SRADIEYI 1 �J DISPENSER aw. <br />Use control box If relay In dispenser Is rated at 100'ea11 ___ I I <br />lova than 1.1/211P. -� <br />5. Suggentod wlring diagram WITH optional control box. Fig. 2 Suggested diagram for wiring dual menllold system. <br />4 <br />C. DUAL MANIFOLD SYSTEMS <br />Installing dual submorsiblos munifoldod In ilia same system. <br />Thls We of systorn Is often used when greater [law rales are needed. It <br />Installed according to the lllushatlon below (Fig. 1), manifolded systemse <br />offer back-up support In that operations could con tlnue should one unit <br />fall. <br />EMMM Proper check valves, with pressure relief, must be In- <br />stalled In the discharge line of each pump to prevent <br />product frons being pumpod Through the pressure relief <br />syslom ollheadJacent pumpwhon his notrunnhng.Chock <br />valves must be compatible Willi the product being <br />pumped. <br />PRESSURE RELIEF TYPE <br />Fig. 1 Dual submersible manifold Installation. <br />This diagram (Fig 2) shows the wiring allowing both submersibles to <br />operate simultaneously with any combinatlon of dispensers turned on. it,'... <br />To operate Individually, the appropriate toggle switch, located externally <br />on the aide of the control box must be turned off manually. The check <br />valves and 220/240 volt relay are not available from Red Jacket and <br />should be purchased locally. <br />s1o«� o"rt ""ro <br />pmlW iuul Uncles 1@v. RELAY I I <br />ALLEN SRADIEYI 1 �J DISPENSER aw. <br />Use control box If relay In dispenser Is rated at 100'ea11 ___ I I <br />lova than 1.1/211P. -� <br />5. Suggentod wlring diagram WITH optional control box. Fig. 2 Suggested diagram for wiring dual menllold system. <br />4 <br />