INSTALL_1997 - Laserfiche WebLink

Home Browse Search

A. INSTALLING I*gPING UNIT 1. E%TRACTA pump with manhole and optional control box. wtcr,�- 4. Line up discharge outlet. Turn In"Ilghloning" direction only. B. WIRING �Y '111111 t _ •` 2. Install pump In 4" tank opening- Use approved non-setling thread sealant. .11L'1Yl At the factory, the riser pipe Is lightly coated with the appropriate thread sealant and hand -tightened for shipping, rust prevention and for ease of alignment of pump manifold wjlh the dis- charge pipe at Installation. When Install. Ing, apply adequate, bosh, U. L Classified sealant to all threads and lighten securely BEFORE the tank lost. Premature pump motor failure may occur If elements such as mud, send, poagravel, backllll, otc. enter the Intake. When Installing the pump, do not allow the pump Inlet to come In contact with these elements. SYPHON SYSTEMS: Remove the pipe plug from the syphon check valve. A syphon check valve le required for ilio syphon system to function properly. Connect 3/8" copper tubing to highest point on syphon loop. Minimum size for syphon pipe Is 1-1/2 PSI. (Soo photo 5.) ALWAYS DISCONNECT and 2. Remove cover from )unction box. Re - K or TAG OUi the power before move compression seal. Provision sterting to service the pump. has been made for 2 wire, or 3rd wire optlonalground. Pull wires from power 1. Connect electrical conduit through ap• supply through compression seal. proved fillings to junction box. Position and tighten soul securely. 3 0 3. Tighten 4" riser pipe In lank. 5. Typical piping with syphon. 3. Connect wires from power supply to wire In tiro (uncllon box. Make water - pmol splice. Iluplaw covor uuing wa- terproof IhruuJ auulmu.ln a W II optlanal ground wire as shown II applicable. iI I 1 1. E%TRACTA pump with manhole and optional control box. wtcr,�- 4. Line up discharge outlet. Turn In"Ilghloning" direction only. B. WIRING �Y '111111 t _ •` 2. Install pump In 4" tank opening- Use approved non-setling thread sealant. .11L'1Yl At the factory, the riser pipe Is lightly coated with the appropriate thread sealant and hand -tightened for shipping, rust prevention and for ease of alignment of pump manifold wjlh the dis- charge pipe at Installation. When Install. Ing, apply adequate, bosh, U. L Classified sealant to all threads and lighten securely BEFORE the tank lost. Premature pump motor failure may occur If elements such as mud, send, poagravel, backllll, otc. enter the Intake. When Installing the pump, do not allow the pump Inlet to come In contact with these elements. SYPHON SYSTEMS: Remove the pipe plug from the syphon check valve. A syphon check valve le required for ilio syphon system to function properly. Connect 3/8" copper tubing to highest point on syphon loop. Minimum size for syphon pipe Is 1-1/2 PSI. (Soo photo 5.) ALWAYS DISCONNECT and 2. Remove cover from )unction box. Re - K or TAG OUi the power before move compression seal. Provision sterting to service the pump. has been made for 2 wire, or 3rd wire optlonalground. Pull wires from power 1. Connect electrical conduit through ap• supply through compression seal. proved fillings to junction box. Position and tighten soul securely. 3 0 3. Tighten 4" riser pipe In lank. 5. Typical piping with syphon. 3. Connect wires from power supply to wire In tiro (uncllon box. Make water - pmol splice. Iluplaw covor uuing wa- terproof IhruuJ auulmu.ln a W II optlanal ground wire as shown II applicable.