Laserfiche WebLink
4 <br />0 <br />Flexible Entry Boots <br />Environ offers a complete line of environmentally safe <br />sump entry seals In sizes to seal standard electrical <br />conduit, rigid pipe and flexible pipe. Environ offers <br />Flexible Entry Boots in both 'Studded Ring' and <br />"Compression Ring' configurations. Both of these type <br />entry boots are made of materials suitable for <br />underground burial and exposure to fuels. <br />E <br />Flexible Entry [loot Specifications <br />Part No. <br />Type <br />Use <br />Nominal Size <br />Boot ID <br />Hole Saw Size <br />FEB -3050 <br />Studded Ring <br />Conduit <br />1/2" <br />.84' <br />&3/8' <br />FEB -3075 <br />Studded Ring <br />Conduit <br />3/4" <br />1.05 <br />2-3/8" <br />FEB -0075 <br />Expansion Ring <br />Conduit <br />- 3/4" <br />1.05" <br />4-1/4" <br />FEB -3100 <br />Studded Ring <br />Conduit <br />1" <br />1.32" <br />2-3/8" <br />FE8-8150 <br />Studded Ring <br />Pipe <br />- 1.12" <br />1.81' <br />- 4-1/4' <br />FES -0150 <br />Expansion Ring <br />Pipe <br />1-1/2" <br />1.81" <br />4-1/4" <br />FEB -6200 <br />Studded Ring <br />Pipe <br />- 2" <br />2.37" <br />- 4-1/4' <br />FEB -0200 <br />Expansion Ring <br />Pipe <br />2" <br />2.37" <br />5-1/2" <br />FEB -6300 <br />Studded Ring <br />Pipe <br />3- <br />3.50' <br />4-1/4' <br />FEB -0300 <br />Expansion Ring <br />Pipe <br />3" <br />3.50" <br />5-1/2" <br />FEB -7390 <br />Studded Ring <br />Pipe <br />3.5" <br />3.90" <br />5-1/2' <br />FEB -7400 <br />Studded Ring <br />Pipe <br />4" <br />4.50" <br />5'1/2" <br />FEB -8600 <br />Studded Ring <br />Pipe <br />6" <br />6.501 <br />Use Sabre Saw <br />Studded Ring Flexible Entry Boots <br />This style of Flexible Entry Boot mounts to a sump wall by means of stainless <br />steel studs, a compression ring and nut fasteners and seals to the pipe or <br />conduit by using a band clamp. To install this type of boot, it is necessary to <br />first drill a series of smaller stud holes around the opening using a templet <br />and then the boot opening using the appropriate size hole saw. Detailed <br />installation Instructions are packaged with the boots. <br />Entry Boot Flexibility <br />All entry boots are designed to provide universal <br />flexibility for the pipe or conduit providing up and <br />down, side to side, back to front movement as <br />well as angled pipe entries. This flexibility is <br />important for aligning pipe connections or as a <br />stress relief for the pipe during backfilling and <br />ground movement. <br />Expansion Ring Flexible Entry Boots <br />This style of Flexible Entry Boot mounts to a sump wall by means of a nylon <br />expansion ring and to the pipe or conduit using a band clamp. To Install this <br />type of boot it is only necessary to drill the boot opening using the <br />appropriate size hole saw. The smaller stud holes are not required. This <br />boot uses an internal expansion ring to create the pressure seal. Detailed <br />Installation instructions are packaged with the boots. Available soon. <br />Angled Entries <br />Flexible Entry Boots are designed to permit up to <br />a 30' angle of flexibility for pipe and conduit <br />entries. Angles greater than 30' could prevent <br />the boot from sealing around the pipe or conduit. <br />If angled entries are required, make sure the <br />boot opening in the wall has a sanded edge so <br />as not to damage the entry boot. <br />14 <br />Round Surface Installations <br />Flexible Entry Boots may be Installed on round <br />surfaces which have a radius diameter greater <br />than 30" (750mm). The installation procedures <br />are the same as described above except that the <br />bolt holes should be made slightly larger after <br />Initial drilling. Only 'Studded Ring" entry boots <br />should be used on round surfaces.` <br />