|
PERFORMANCE SPECIFICATION - CONTINUED
<br /> SECTION Vli ELECTRICAL WORK --CONTINUED SECTION VII ELECTRICAL WORK - CONTINUED SECTION IX CANOPIES - CONTINUED OR 11.24,
<br /> PART 2 - PRODUCTS PART 3 - EXECUTION - CONTINUED PART 1 - GENERAL - CONTINUED 9 .
<br /> 2.1 IDENTIFICATION OF EQUIPMENT AND WIRING: PROVIDE IDENTIFICATION WITH 3.8. OPERATING AND ACCEPTANCE TESTS: 1.1.1 COMPLETE FABRICATION DRAWINGS INCLUDING FOOTINGS DESIGN.
<br /> DYMO TAPE OR EQUAL FOR ALL SERVICE €NTRANCE AND DISTRIBUTION 3.8.1 CONDUCT OPERATING TEST ON ENTIRE ELECTRICAL I INSTALLATION; ALL SYSTEMS 1.1.2 COMPLETE ABOVE GROUND STRUCTURAL SUPPORT SYSTEM.
<br /> EQUIPMENT INCLUDING MAIN SWITCHGEAR, PANELS, DISCONNECT SWITCHES, MUST BE COMPLETE AND IN GOOD OPERATING ORDER. REFER TO START-UP AND FINAL 1.1.3 STEEL ROOF DECK, SMOOTH WHITE 907 REFLECTIVE PAINT. w
<br /> CONDUITS, ETC., AND FOR MOTOR FEEDERS INCLUDING SWITCHES, STARTERS CHECK-OUT OF SYSTEM COVERED ELSEWHERE. 1.1.4 ROOF BRACING. _
<br /> AND MOTORS. DO NOT START OR OPERATE EQUIPMENT WITHOUT SPECIFIC DIRECTIVES OF OWNER'S ~
<br /> 1.1.5 CAP FLASHING.
<br /> 2.2 LIGHT FIXTURES: TO BE PROVIDED BY OWNER. SPECIFIED REPRESENTATIVE. ANY DAMAGE TO OWNER'S EQUIPMENT DUE TO
<br /> 2.3 CONDUITS: PROVIDE THE FOLLOWING TYPES OF RACEWAYS IN ACCORDANCE DEFECTIVE INSTALLATION AND/OR OPERATION WILL BE THE RESPONSIBLITY OF THAT 1.1.6 DOWNSPOUTS - INTERNAL INSIDE COLUMNS.
<br /> SUBCONTRACTOR FOR CORRECTION, REPLACEMENT AND/OR MONETARY COMPENSATION 7.1.7 PERMITS AND INSPECTIONS. W
<br /> WITH THE SPECIFIC APPLICATION OF LOCATION INDICATED. Y
<br /> AS REQUIRED. 7.1.8 INSTALLATION AND FRAMING FOR OWNER-SUPPLIED FASCIA SIGNS INCLUDING ELECTRIC.
<br /> 2.3.1 RIGID GALVANIZED STEEL: WHERE EXPOSED TO THE WEATHER; FOR 3.8.2 MAKE INSULATION TESTS ON MAIN SERVICE EQUIPMENT AND ALL FEEDERS AND
<br /> s" 1,1.9 INSTALLATION AND FRAMING FOR FASCIA MATERIAL AS PER OWNER SPECIFICATIONS.
<br /> ENCLOSING MAIN GROUNDING CONDUCTOR: WHERE REQUIRED FOR
<br /> MECHANICAL PROTECTION OR WHERE SPECIFICALLY INDICATED. MATERIAL TESTPANEGROUND:
<br /> SHALL BE AS MANUFACTURED BY GENERAL ELECTRIC. REPUBLIC 3.8.3 TEST GROUND: RESISTANCE TO GROUND SHALL NOT EXCEED 25 OHMS. PART 2 PRODUCTS
<br /> 2J ROOF STEEL DECK: ROOF STEEL DECK SHALL BE 2 1/4 " MINIMUM DEEP, 24 GAUGE
<br /> YOUNGSTOWN STEEL AND TUBE, OR EQUAL. PROTECT WITH ASPHALTIC 3.8.4 INSPECT ALL PANELBOARDS. ALL CONNECTIONS MUST BE TIGHT AND SECURE.
<br /> BAKED WHITE ENAMEL STEEL WITH MINIMUM SECTIN MODULES OF 0.25 IN 1/4 3 MOMENT
<br /> PROTECTIVE COATING WHEN BELOW FINISH GRADE. 3.9 "AS-BUILT" DRAWINGS: FURNISH OWNER'S CONSTRUCTION MANAGER WITH ONE SET
<br /> OF INERTIA OF 0.030 IN 74/4 4.
<br /> 2.3.2 SEALOFFS: WHERE CONDUITS EXIT FLOOR OR CONCRETE AT DISPENSERS, OF MARKED-UP PRINTS SHOWING "AS-BUILT" INSTALLATION. 2.2 STRUCTURAL STEEL:
<br /> TANK GAUGING, SUBMERSIBLE PUMPS AND WHERE CONDUITS TRANSVERSE 3.10 FINAL ACCEPTANACE; UPON COMPLETION OF WORK, PRESENT CERTIFICATE OF APPROVAL
<br /> HAZARDOUS ZONE (I.E. YARD LIGHTS, AIR/WATER UNIT, LIGHTED SIGNAGE) OF LOCATION OR GOVERNING INSPECTION AUTHORITY. 2.2.1 ALL STRUCTURAL STEEL SPECIFICATIONS FOR STRUCTURAL
<br /> BE A.S.T.M. A-36 AND SHALL COMPLY WITH THE STANDARD
<br /> UCTURAL STEEL FOR BUILDINGS OF A.LS.C. AND WITH THE
<br /> SEE ELECTRICAL SITE PLAN FOR ZONE LIMITS. 3.11 CLEAN-UP: CLEAN UP ALL DEBRIS CAUSED BY WORK OF THIS SECTION, KEEPING A.I.S.C. CODE OF STANDARD PRACTICE (LATEST EDITION).
<br /> 2.3.3 PVC CONDUITS: ALL WIRING RUNS BURIED UNDERGROUND UNLESS THE PREMISES CLEAN AND NEAT AT ALL TIMES. 2.2.2 HIGH STRENGTH BOLTS SHALL CONFORM TO THE STANDARD SPECIFICATIN A,5.T.M.
<br /> OTHERWISE INDICATED, MATERIAL SHALL BE HEAVY WALL, TYPE it RIGID SECTION VIII PAINTING A325", AND SHALL BE PROVIDED WITH CARBONIZED WASHERS UNDER THE NUTS.
<br /> SCHEDULE 40 AS MANUFACTURED BY CARLON, BALDWIN. TRIANGLE, OR EQUAL. 2.2.3 ALL OTHER BOLTS SHALL BE A-307 AND SHALL CONFORM TO A.S.T.M. STANDARDS,
<br /> PVC CONDUITS SHALL BE U.L. LISTED AND APPROVED. PART 1 - GENERAL WITH WASHER REQUIRED.
<br /> 2.4 CONDUCTORS: 1.1 SCOPE: THIS SECTION COVERS THE FURNISHING OF ALL LABOR, MATERIALS,
<br /> 2.2.4 ALL HIGH STRENGTH BOLTS SHALL BE TORQUED TO PROVIDE A MINIMUM TENSION
<br /> 2.4.1 FURNISH AND INSTALL COLOR CODED COPPER CONDUCTORS, 600 VOLT, OF
<br /> SERVICES, EQUIPMENT AND APPLIANCES IN CONJUNCTION WITH OR PROPERLY INCIDENTAL BOLT OF 90% OF MINIMUM PROOF LOAD OF THE BOLT. N
<br /> SIZES INDICATED. MINIMUM SIZE #12 (TFFN) EXCEPT FOR SIGNAL AND CONTROL TO THE COMPLETION OF ALL PAINTING OF SURFACES COMPLETE, INCLUDING
<br /> 2.2.5 TUBE COLUMNS SHALL COMPLY WITH A-53, GRADE B. O
<br /> CIRCUITS AND WHERE OTHERWISE NOTED. TYPE TW (60 DEGREES CENTIGRADE) PAINTING OF THE FOLLOWING SURFACES: ~
<br /> FOR GENERAL BRANCH CIRCUIT WIRING; TYPE THN (90 DEGREES CENTIGRADE) 2.2.6 ALL TUBE COLUMNS SHALL BE 46 KSI STEEL. y
<br /> FOR SUPPLY CONNECTIONS TO LIGHT FIXTURES. INSTALL PER COLOR CODE OF 1.1.1 MISCELLANEOUS METAL, DOWNSPOUTS, COLUMNS, POSTS, ISLAND FORMS, VENT 2.2.7 ALL WELDING SHALL BE WITH E70XX ELECTRODES AND BE ACCOMPLISHED BY
<br /> NEC. LINES, MANHOLE COVERS AND ELECTRICAL CONDUITS. CERTIFIED WELDERS. w
<br /> w
<br /> CL
<br /> 2.3 FASCIA;
<br /> 2.4.2 SHIELDED CABLES: PROVIDE SHIELDED CABLE FOR INTERCOM AS PER 1.2 PAINTING DOES NOT INCLUDE: �
<br /> MANUFACTURER'S SPECIFICATIONS AND AS REQUIRED ON DRAWINGS. 1.2.1 PAINTING CANOPY SOFFITS.
<br /> 2.3.1 FASCIA BACKING PLYWOOD SHALL BE MINIMUM 1/2 " THICK MARINE GRADE. MARINE
<br /> 2.5 SPLICES AND CONNECTIONS: PROVIDE SPLICES ONLY IN READILY ACCESSIBLE
<br /> 1.2.2 PAINTING LIGHT FIXTURES. GRADES SHALL MEET THE REQUIREMENTS OF EXTERIOR TYPE AND SHALL BE ON OF
<br /> OUTLET BOXES. PROVIDE INSULATED PRESSURE CONNECTORS OR "CRIMP-ON" 1.2.3 PAINTING FASCIA SIGN FRAMES, GRADE 1-1, HIGH DENSITY OVERLAY.
<br /> SLEEVES WITH OVERALL NYLON INSULATORS FOR CONDUCTORS, CONNECTORS
<br /> SHALL BE 3M "SCOTCHLOK", BUCHANNAN SPLICE CAP$ WITH INSULATED WRAP, 1.2.4 PAINTING GASOLINE EQUIPMENT. 2.3.2 VERTICAL SUPPORTS SHALL BE 14 GA STEEL. STUDS AT 14" O.C. OR 3 X 3 X 1/4 q w Yo
<br /> STEEL ANGLES ALL AT 24" O.C. WITH CORRESPONDING MEMBERS TOP AND BOTTOM
<br /> OR IDEAL "CRIMP-SLEEVES" WITH SCAP CAP INSULATOR OR EQUAL. 1.3 COLOR SCHEDULE: COLOR OF PAINTS SHALL BE AS LISTED IN COLOR SCHEDULE. p ; ^ tl
<br /> 2.6 PANELBOARDS: PART 2 PRODUCTS SUPPORT. u s Q'
<br /> 2.6.1 BRANCH CIRCUIT PANELBOARDS: PROVIDE FLUSH-MOUNT CIRCUIT BREAKER TYPE 2.1 PAINT MANUFACTURERS AND PRODUCTS: PAINTING SYSTEM AS SPECIFIED HEREIN IS 2.3.3 ��
<br /> SCREWS FOR FASCIA SHALL BE ALUMINUM OR GALVANIZED SIZE AS REQUIRED. 2� bA '
<br /> PANELBOARDS WITH THERMAL MAGNETIC, MOLDED CASE, GENERAL ELECTRIC TYPE NLAB BASED ON PRODUCTS OF THE GLIDDEN COATING & RESINS COMPANY, A DIVISION OF 2,3.4 REFER TO PROJECT DRAWINGS FOR FASCIA MATERIAL AND INSTALLATION. MATERIAL J/� * $�
<br /> SHALL BE ONE OF THE FOLLOWING:
<br /> OR APPROVED EQUAL, WITH PLUG-IN CIRCUIT BREAKERS, GENERAL ELECTRIC TYPE NLQT SCM CORPORATION. HOWEVER, EQUAL PAINTING SYSTEMS OF PRATT & LAMBERT, PPG
<br /> OR APPROVED EQUAL. PROVIDE GROUNDING TERMINAL BLOCK IN EACH PANELBOARD. INDUSTRIES AND BENJAMIN MOORE WILL BE CONSIDERED. A. BACK-LIGHT FABRICATED SIGN SYSTEM
<br /> SEE INDIVIDUAL PANEL SCHEDULE ON DRAWINGS. 2.2 PAINTING COATS AND PRODUCTS: B. PREFINISHED METAL FASCIA SYSTEM.
<br /> 2.6.2 ACCEPTABLE SUBSTITUTES: DISTRIBUTION EQUIPMENT EQUIVALENT IN TYPE, C. PREFINISHED FASCIA MATERIAL AS SELECTED. n i a
<br /> CLASSIFICATION AND QUALITY IN ACCORDANCE WITH NEMA STANDARDS AS MANUFACTURED 2.2.7 GASOLINE ISLAND METALS AND VENT LINES: SHAH BE GLADDEN SPREAD LUSTRE
<br /> BY CUTLER-HAMMER, FEDERAL PACIFIC, ITE, SQUARE D AND WESTINGHOUSE ARE ALKYD SEMI-GLOSS PAINT #4656 ARCHITECTURAL BROWN. PART 3 - EXECUTION o �
<br /> ACCEPTABLE AS SUBSTITUTIONS, WHEN APPROVED IN WRITING. 2.2.2 PAINT ALL MANHOLES COVERS AND 4" SURROUNDING CONCRETE, INSIDE AND OUT, 3.1 FABRICATION DRAWINGS: o a
<br /> PART 3 - EXECUTION IN ACCORDANCE WITH STANDARD INDUSTRY COLOR CODE AS SHOWN: 3,1.1 CANOPY CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING ENGINEERED AND Q U
<br /> 3.t GENERAL: COORDINATE TIME SCHEDULES, INSTALLATION, HOOK-UPS AND MISCELLANEOUS API COLOR CODES: STAMPED SHOP DRAWINGS FOR OVERHEAD STRUCTURE AND FOUNDATION SYSTEMS. z a.
<br /> w $
<br /> PROCEDURES WITH ALL OTHER TRADES THAT WILL BE INVOLVED TO EXPEDITE THE LEADED REGULAR SOLID BLUE 3.1.2 DRAWINGS SHALL SHOW PROJECT LOCATION AND ADDRESS, > i O J
<br /> COMPLETION OF THE CONTRACT. THE ELECTRICAL SUBCONTRACTOR SHALL BE SOLEY LEADED PREMIUM SOLID RED 3.1.3 ORIGINAL ENGINEER'S STAMP FOR APPROPRIATE STATE SHALL BE AFFIXED TO
<br /> RESPONSIBLE FOR THE PROPER INSTALLATION OF THE ELECTRICAL WORK, UNLEADED REGULAR WHITE W/BLACK CROSS a
<br /> UNLEADED PREMIUM RED W/WHITE CROSS EACH PAGE OF DRAWINGS, n � � a
<br /> 3.2 CONDUITS: FURNISH AND INSTALL A COMPLETE OVERALL CONDUIT RACEWAY SYSTEM 3.1.4 SHOP DRAWINGS SHALL SPECIFICALLY CALL OUT SOILS REPORT NUMBER AND DATE ..
<br /> FOR ALL WIRING AND CONDUCTORS. PROVIDE SIZES AND RACEWAYS AS INDICATED ON LEADED REGULAR W/ EXTENDER BLUE W/WHITE BAND
<br /> DRAWINGS OR AS REQUIRED BY NATIONAL ELECTRICAL CODE FOR CONDUCTORS TO BE UNLEADED REGULAR W/EXTENDER WHITE W/BLACK CROSS & BLACK BAND FOR WHICH CANOPY FOOTINGS WERE DESIGNED.
<br /> CONTAINED. ALL RACEWAYS SHALL CONFORM TO THE FOLLOW REQUIREMENTS: UNLEADED PREMIUM W/EXTENDER RED W/WHITE CROSS & WHITE BAND 3.1.5 SHOP DRAWINGS SHALL SPECIFICALLY CALL OUT SIZE, WEIGHT, TYPE AND NUMBER
<br /> 3.2.1 CONCEAL ALL CONDUIT RUNS EXCEPT WHERE EXPOSED RUNS ARE AUTHORIZED DIESEL SOLID YELLOW OF ALL STRUCTURAL MEMBERS. 2
<br /> BY OWNER'S CONSTRUCTION MANAGER IN WRITING. VAPOR RECOVERY SOLID ORANGE 3,1.6 ALL DESIGN LOADS SHALL COMPLY WITH U.B.0 LATEST EDITION AND LOCAL
<br /> 3.2.2 ACTUAL CONDUIT RUNS ARE NOT GENERALY INDICATED; CONDUITS AT TANKS PART 3 - EXECUTION BUILDING DEPARTMENT REQUIRED LOADINGS, WHICHEVER IS MOST STRINGENT. MINIMUM
<br /> SHALL NOT CROSS OVER TANKS, PLACE CONDUIT THROUGH EACH END OF TANK 3.1 PROTECTION: COVER ENTIRE CONCRETE SURFACES. NO PAINT OR SOLVENT SHALL BE - AND DEAD LOAD 35 DESIGN LOADS SHALL BE CONSIDERED TO BE: WIND 100N, LIVE OR AS LOCAL STRUCTURAL DESIGN DICTATES. IF
<br /> iF APPLICATION
<br /> UPLIFT 35�
<br /> EXCAVATION AND PLACE FIELDS PARALLEL WITH AXIS OF TANKS, ALLOWED TO COME IN CONTACT WITH CONCRETE SURFACES. WHERE IT BECOMES
<br /> NECESSARY, IN ORDER TO EXECUTE HIS OWN WORK, FOR PAINTER TO REMOVE IS SUBJECT TO HIGH ALTITUDE (SNOW) LOADING, DESIGN SHALL BE ADJUSTED 70
<br /> 6 3.2.3 CLEAN AND DRY ALL RACEWAYS THOROUGHLY BEFORE CONDUCTORS ARE PULLED IN. COMPLY ACCORDINGLY,
<br /> 3.2.4 FLASH AND COUNTER FLASH CONDUITS WHICH PENETRATE THE CANOPY DECKING. COVERINGS, PLATES, ETC., PLACED BY OTHER CONTRACTORS IN ANY BRANCH OF THE
<br /> WORK, HE SHALL REPLACE SAME IN PROPER MANNER. IN SITUATIONS WHERE SAID 3.1.7 DEFLECTION OF ALL STRUCTURAL MEMBERS SHALL BE LIMITED TO SPAN/240 FOR
<br /> 3.2.5 PROVIDE SEAL-OFF FITTINGS WHERE CONDUIT RUNS ENTER OR LEAVE. COVERINGS, PLATES, ETC., CANNOT BE READILY REMOVED, PAINTER SHALL PROTECT THE L.L. ONLY.
<br /> HAZARDOUS AREAS OF DISSIMILAR CONDITIONS SUCH AS TEMPERATURE, HUMIDITY, ETC. WORK IN SOME OTHER SATISFACTORY MANNER. OILY RAGS AND WASTE MUST BE 3.1.8 ATTACH DECK STRUCTURAL SUPPORTS WITH 3/8 " DIAMETER BOLTS.
<br /> 3.2.6 FURNISH AND INSTALL COMPLETE RACEWAY SYSTEM, INCLUDING CONDUITS AND REMOVED EVERY NIGHT. UNDER NO CIRCUMSTANCES SHALL THEY BE ALLOWED TO 3.1.9 ROOF DECK SHALL BE AN I.C.B.O. APPROVED DIAPHRAGM DECK AND ATTACHED IN
<br /> OUTLETS, AS INDICATED AND AS REQUIRED FOR INTERCOM SYSTEM, GAS PRICE SIGNS, ACCUMULATE. PAINTING SUBCONTRACTOR SHALL BE RESPONSIBLE FOR ANY DAMAGE DONE A MANNER THAT COULD BE CONSIDERED A DIAPHRAGM. AN ALTERNATE TO THIS IS �+
<br /> SECURITY LIGHTING AND CANOPY LIGHTING SYSTEM, AND LIGHTED FASCIA SYSTEM TO THE WORK OF OTHER SUBCONTRACTOR$ AND SHALL REPAIR OR REPLACE AS 1/2" DIAMETER STEEL ROD DIAGONAL X-BRACING WITH TURNBUCKLES. LAYOUT OF W -
<br /> u WHERE APPLICABLE. CONDUIT AMOUNTS AND SIZES SHALL BE AS SHOWN ON NECESSARY TO THE SATISFACTION OF THE OWNER. - ROD BRACING AND CONNECTIONS TO STRUCTURAL MEMBERS SHALL BE APPROVED BY
<br /> ti GASOLINE DRAWINGS. ADDITIONAL CONDUITS AND CIRCUITS WILL BE REQUIRED
<br /> 3.2 PREPARATION OF SURFACES: INSPECT ALL SURFACES TO BE PAINTED. REPORT ANY STRUCTURAL ENGINEER.
<br /> FOR LIGHTED FASCIA SYSTEMS. PROVIDE AS REQUIRED. DISCREPANCIES TO THE CONTRACTOR PRIOR TO START OF WORK. STARTING OF PAINT3
<br /> 3.3 :LIGHTINGINSTALL ALL LIGHTING FIXTURES AND LAMPS AS INDICATED ON DRAWINGS. APPLICATION SHALL CONSTITUTE ACCEPTANCE OF SURFACES AS SUITABLE FOR THE 3.1.10 CONCRETE FOOTINGS SHALL BE MADE WITH STONE AGGREGATE AND SHALL HAVE
<br /> N A COMPRESSIVE STRENGTH TO A MINIMUM 3000 LBS. PER SQUARE INCH WITHIN 28
<br /> SECURELY MOUNT ALL FIXTURES; PROVIDE ALL ADDITIONAL HANGERS AND SUPPORTS AS RECEPTION OF PAINT APPLICATION. ALL SURFACES SHALL BE CLEAN AND DRY, BETWEEN DAYS AFTER POURING.
<br /> NECESSARY TO SECURELY FASTEN AND SUPPORT FIXTURES. CLEAN ALL FIXTURES AND .j[ \
<br /> 50 AND 90 DEGREES FARENHEI7 AT TIME OF PAINT APPLICATION. CLEAN METAL OF MILL 4 �
<br /> LAMPS UPON COMPLETION OF THE PROJECT. CONTRACTOR SHALL VERIFY AMOUNT AND SCALE, RUST, OIL, GREASE AND FOREIGN MATTER. CLEAN GALVANIZED METAL ACCORDING 3.1.11 ALL FOUNDATION METAL REINFORCEMENT SHALL BE DEFORMED TYPE BARS
<br /> TYPE OF ISLAND/CANOPY LIGHTING SYSTEMS, SHOULD ADDITIONAL CONDUITS/CIRCUITS TO SSPC-SP 1 -63 SOLVENT CLEANING, PROTECT ADJACENT AND FINISHED WORK FROM (EXCEPT #2 BARS) AND SHALL CONFORM TO THE REQUIREMENTS OF THE "STANDARD
<br /> SPECIFICATION A.S.T.M. 615 GRADE 400
<br /> .
<br /> w BE REQUIRED, VERIFY THROUGH LOCAL CONSTRUCTION OFFICE AND PROVIDE AS REQUIRED. PAINT. .�
<br /> 1LAY SHOW LOCATION OF DOWNSPOUTS,
<br /> 3.4 SIGNS AND LIGHTED FASCIA: VERIFY FINAL LOCATIONS AND TYPE WITH OWNER, 3.3 APPLICATION OF PAINT: DO NOT THIN, ADULTERATE OR CHANGE MATERIALS EXCEPT 3. .12 THE SHOP DRAWINGS SHALL AS RE
<br /> FURNISH AND INSTALL ALL CONDUITS AND WIRES WITH STUB-OUTS AS DIRECTED. MAKE AS RECOMMENDED BY MANUFACTURER. EMPLOY ONLY SKILLED MECHANICS FOR WORK. ALL GASOLINE VENT LINES, ETC., RELATED ANY AND ALL UTILITIES AND/OR DATES �
<br /> FINAL CONNECTIONS AS REQUIRED. - PAINTING SHALL BE BRUSHED, SPRAYED OR ROLLED EVENLY FOR THOROUGH COATS PARING AT COLUMN LOCATIONSS., REROOF DRAINS AND LEADERS SHALL BE DIRECTED
<br /> igJUL97
<br /> 3.5 OUTLETS: COORDINATE LOCATION OF ALL ELECTRICAL EQUIPMENT, INCLUDING INTERCOM WITHOUT RUNS, SAGS OR OTHER BLEMISHES, ALLOW EACH COAT TO DRY BEFORE APPLYING DOWN THE INTERIOR CANOPY COLUMN EXITING SIDE OF ISLAND FORM, LEVEL OR ABOVE PROJECT 0.2
<br /> SUBSEQUENT COATS. ALL SURFACES TO RECEIVE A MINIMUM OF 2 COATS AS NECESSARY TO FINISH GRADE OF CONCRETE SIDE PAD ON DOWNHILL SIDE OF ISLAND.
<br /> OUTLETS, SWITCHES, RECEPTACLES, CONTROLLERS, PANELBOARDS, SWITCHGEAR, ETC., TO DOWNSPOUTS 3010.20 J
<br /> OUTLDRA1NNt
<br /> INTERFERENCE AND OBSTRUCTIONS WITH EQUIPMENT OF OTHER CRAFTS AND TRADES ACHIEVE AN APPROVED FINISH. APPLICATION OF PAINT, ETC., SHALL BE IN STRICT SHALL BE 4" X 4" CONSTRUCTED OF 16 GA GALVANIZED METAL OF FREEZE-PROOF
<br /> AV ELECTRICAL EQUIPMENT WILL NOT BE BLOCKED OR MADE INACCESSIBLE T COMPLIANCE WITH MANUFACTURER'S DIRECTIONS. OR OPEN-FACE DESIGN, STRAP TO CANOPY COLUMN AT 24" O.C. MSP
<br /> THAT
<br /> 3
<br /> INOPERABLE, PROVIDE WEATHERPROOF OUTLETS WHERE EXPOSED TO THE WEATHER OR 3.4 CLEAN-UP: CLEAN UP ALL DEBRIS CAUSED BY THE WORK OF THIS SECTION, KEEPING .1.13 INCLUDE IN DESIGN PROVISION FOR OVERFLOW DEVICE AT OPPOSITE CORNERS OR
<br /> APPROVE
<br /> TO MOISTURE. THE PREMISES CLEAN AND NEAT AT ALL TIMES. CANOPY. � CL
<br /> . 3.1.14 CONSTRUCTION NOT SPECIFICALLY INDICATED SHALL BE ACCOMPLISHED PER
<br /> 3.6 ISOLATED GROUND: IT IS MANDATORY THAT GASOLINE EQUIPMENT REQUIRING ISOLATED . SECTION IX CANOPIES -
<br /> GROUND. SHALL BE PROVIDED WITH SAME. MINIMUM CIRCUITS REQUIRED, BUT NOT. MINIMUM REQUIREMENTS OF THE UNIFORM BUILDING CODE, LATEST EDITION. DRAWING
<br /> GROUND
<br /> LIMITED TO, SHALL BE: INTERCOM, GA CONSOLE AND GASOLINE REQUIRED,
<br /> TANK' MBUT ANG SYSTEM, - 3.1.15 IF THERE ARE ANY CONFUCTS BETWEEN LINES ON DRAWINGS AND GENERAL NOTES
<br /> 3.7 EXCAVATION AND BACKFILLING: ALL EXCAVATION AND BACKFILLING NECESSARY FOR THE PART 1 C GENERAL OR WITH SPECIFICATIONS, THE MOST STRINGENT REQUIREMENTS GOVERN. FSI A
<br /> INSTALLATION OF ELECTRICAL WORK SHALL BE INCLUDED IN THIS SECTION AND COMPLY _ 7.1 . SCOPE: THIS SECTION COVERS, THE FURNISHING AND INSTALLATION OF ALL ITEMS FOR 3.7.18 ANY DEVIATION FROM THE PLANS OR SPECIFICATIONS SHALL BE APPROVED BY Q `'t
<br /> THE INSTALLATION OF A COMPLETE GASOLINE CANOPY INCLUDING: - SOUTHLAND'S CONSTRUCTION REPRESENTATIVE.
<br /> WITH SECTION III, EARTHWORK. - _
<br />
|