INSTALL 2018 - Laserfiche WebLink

Home Browse Search

to anchor points,and the two strap halves are connected to each other 1.3.7.3.2.The particular configuration of hardware will be determined at the top of the tank.See Figure 1-5. by the contractor,the owner orthe owner's representative,but is to adhere 1.3.7.2.II.MOH anchorstrapsare tobeinstal Iedinthe following way: to the following: Anchoring hardware must be manufactured to industry standards Figure 1-5 and dimensions,and sized according to Table 1-3. • All exposed metal on the anchoring system must be coated IIIII= Load Binder Strap Tee IIIII—IIIII or galvanized to protect against corrosion. Assembly -IIIII If the hardware used is not provided by us,contact the hardware IIIII= IIIII=IIII manufadu rer or supplier for specific information on hardwareand its use. IIIII=IIIII II=IIIII IIII=II MOH IIIII IIIII Minimum Turnbuckle IIIII—IIIII Strap _ Tank Diameter(by Type) Minimum Wire IIIII— IIII Diameter Hook Jaw Eye Rope Diameter IIIII=IIIII -IIIII 4-fast 4" /z" K3�8" IIIII=11IIIII=IIIII — ea mangy'. — 6-foot 3/4" '/i' 11i 3/e" f P11 IN 8-foot 11/4" 3/4" a/a" '/z" • liftthe strap with the hook end down and the hook facing away from the tank • lower the hook end of the strap between the tank and the anchor 10-foot P/4" 3/4" 3/4" '/z" Point,andhook the strap to the anchor point 12-foot 11/4" 3/4" i 3/4" Yz" • put a washer and a blind nut(acorn nut)on one end of the threaded rod. • Feed the rod through the hole in the strap-end connector 1.3.7.3.3.When D-ring/D-ring straps are shipped and turnbuckles • put a washerand a nut on the other end of the threaded rod are ordered from us,we mayship extra hardware that may or may not • centerthe wear plate on the top center line of the marked ribs be necessary with alternate deadmen placement. • lowerthe threaded rod,washerand nut into the channel section 1.3.7.3.4.Locate the anchor points as shown in Figurel-band on the strap-end connector,taking care to place the washerand nut on the outside of the connector Table 1.4.Refer to dimensions in Table 1.4.Align(within a tolerance • hand-tighten the nuts of±1 inch)all anchor points. 1.3.7.2.12.Repeat the bulleted items in 1.3.7.2.12 for the second Figure 1-6 rod of the assembly. IIIII—IIIII ` I IIII 1.3.7.2.13.Afterthe two threaded rods are placed,tighten thethreaded III— IIII— rods,using a torque wrench to tighten to 25-30 foot-pounds,or unti l snug. —IIII 1.3.7.2.14.Repeat the bulleted items in 1.3.7.2.12 for each of the load binder assemblies. IIIII= III=IIIII 1.3.7.3.HARDWARE AND ANCHOR POINTS IIIII III IIIII—IIIII 1.3.7.3.I.When ouranchoringhardware isnotbeingused,theinstalling IIIII—IIIII B A contractor is responsible for providing hardware and anchor points IIII III — — 12 Dea man 0 — IIIII IIIII of sufficient size and strength for the tank being installed. Nominal Tank Diameter A:Strap Eye B:Alternate Dimension C:Strap Length D:Center ofTank To Anchor Point to Center of Deadmen 4-foot 10"[25 cm] i not rec commended 00–[254 cm] 31"[79cm] 6-foot 23"[58 cm] 145'[368cm]o43'[111 cm] 8-foot(Red Tank) 29"[ 4cm] 17"[43 cm] 181 [460 cm] 53'[135 cm] 8-foot(Green Tank) 30"[76 cm] 18"[46 cm] 195"[495 cm] 57"[145 cm] 10-foot(Red Tank) 38''[97cm] 26"[66cm] 236"[600 cm] 70"[178 cm] 10-foot(Green Tank) 39"[100 cm] 27"[69 cm] 236"[600 cm] 71"[180 cm] 12-foot 46"[117 cm] 34"[86 cm] 271"[688 cm] 88"[224 cm] 10 I: PLANNING FOR INSTALLATION