Laserfiche WebLink
15.4.2.2.Once the tank is installed,the level of the monitoring 15.4.3.2.After this test.reset the monitoring-fluid level to a <br /> fluid may fluctuate due to such things as: position based on line product level. (See SECTION 15.4.2.) <br /> • product level <br /> groundwater fluctuation CONTAINMENT16, INSTALLING <br /> • tank filling and emptying <br /> • product-temperature vanstlon. 16.1.GENERAL <br /> 16.1.1.Xerxes containment sumps come in a variety of models <br /> 15.4.2.3.To establish the proper operating level for monitoring and sizes,including single-wall and double-wall models.and <br /> fluid,decide what type of monitoring probe will be used in order to round and flat-sided models.These instructions pertain to Xerxes' <br /> determine the tribal starting point for the level in the reservoir. single-wall round containment sumps.Irrsvucl ons for other <br /> 15.4.2.3.1.The typical probe has two sensors(a high-fluid level models are found in Xerxes'supplemental materials,See <br /> and a low-fluid level).When using a two-sensor probe,the start SECTION 200!this manual for information on supplemental <br /> point(the proper level for the monitoring fluid)is midway between instructions. <br /> the two sensors. 161.2.7he containment sump is a terumnation point for secondary <br /> 15.4.2.3.2.If using something other than a two-sensor probe,use piping systems.It is designed to be monitored continuously for leaks <br /> 7 inches from the top of the tank as the start point for the using electronic sensors.Consult federal,state and local codes and <br /> monitoring-fluid levelregulations to ensure proper monitoring compliance. <br /> Nole'When using a probe.do not raise it o8 the lank to meet the WARNING <br /> c o tact with <br /> the <br /> level,the probe must remain upright and in The containment sump system is a confined space,which may <br /> confect with the tOp Of the tank at all limes.(See FIGURE 15-2.) contain hazardous vapors.If work is to be performed inside the <br /> sump,test the atmosphere inside and,If necessary,vent the <br /> space to prevent the development of vacuum or pressure. <br /> b/Y.',ersl <br /> I { Failure to do so could result in death or serious injury. <br /> _9mai ba nm eienr-.i ' <br /> nwk^u <br /> :,,ff„M„l � WARNING <br /> Use air-powered tools to prevent shock,fire or explosion <br /> from flammable liquids and vapors.Failure to do so could <br /> i result In death or serious Injury. <br /> ' kerano- <br /> CAUTION <br /> -AbMW�p^uM kwl <br /> ' Always wear gloves when handling containment sump <br /> components,and always wear eye protection when grinding, <br /> cutting and attaching the sump unit.Failure to do so may <br /> L result in minor or moderate injury. <br /> FIGURE 15.2 <br /> 15.4.2.4.After determining the start point,adjust the monitoring 0 CAUTION <br /> fluid based on the product level: Oo not drop the containment sump assembly components or <br /> allow the sump body to roll.Since high winds could damage <br /> 15,4.2.4.1.ff the tank is between 114 and 1!2 full of product,the the sump components,protect and secure all pieces if windy <br /> proper operating level for the monitoring fluid is at the start point, conditions arise.Failure to follow this caution may result in <br /> 15.4.2.4.2.If the tank is between empty and V4 fug,the proper minor or moderate Injury. <br /> operating level for the monitoring fluid is about 1-1 112 inches CAUTION <br /> Wow the start point, <br /> Failure to follow these instructions may cause water-seal <br /> 15.4.2.4.3.If the tank is between 112 full and full,the proper failure,and may resuh in property damage. <br /> operating level for the monitoring fluid is about 1.1 1,12 inches <br /> above the start point. 16.1.3,Visually inspect all pieces and parts to make sure that no <br /> shipping or handling damage has occurred.If any components are <br /> 15.4.2.5.Add or remove monitoring fluid to reach the proper missing,contact the UST coordinator at the Xerxes plant nearest <br /> operating level for the monitoring fluid you.(See FIGURE 164 or FIGURE 16-2.) <br /> 15.4.3.TRUCHEK9 16.1.4.Do not allempt any repairs to damaged containment sump <br /> 15.4.3,1.If a TRUCHEK test is required after installation,follow components.If damage is detected,contact the UST coordinator <br /> the procedures in the Xerxes TRUCHEK brochure. at the Xerxes plant nearest you. <br /> 11 <br /> I I <br /> ti ' d L96E ' �N S30f�a3S 01 WV91': 6 80OZ 'Z ' �00 <br />