COMPLIANCE INFO 1990 - 2008 - Laserfiche WebLink

Home Browse Search

For FX2V models jjjjjrjj� If flow :restricted to about 8 gpm a. Remove L14-inch pipe plug from tank test port in (11 Ipm)or Is i kwith the nozzle open,the the Packer (on 6-inch Big-Flo applications, re- leak detector has not opened.Repeat step move the 1/4-inch pipe plug from the riser/flange 8a with increased running time of pump assembly). to insure the purging of all air. All air b. Apply a UL-classified non-toxic pipe thread teal- must be purged from the system or the ant to the L4-inch NPT 45-degree elbow and leak detector will restrict flow to about 8 install in tank test port of the packer. On 6-inch 8Pm(11]pm). Big-Flo applications,the 1/4-inch NPT15-&jgree 9. Affix the enclosed decals to the dispenser dial glass on elbow may be installed into the riser/flan;;e as- grade of gasoline upon which the leak detector is sembly. being installed. Additional decals are available;call c. Apply UL-classified non-toxic pipe thread seal- customer service at 1-800-952-8348or(913)498-5700. ant to the 1/4-inch NPT hex nipple and install on 10. Inspect all threadedjoints to assure they are tight and 45-degree elbow that is in the tank test port(or on not leaking. 6 inch Big-Flo riser/flange assembly. d. Apply a UL-classified non-toxic pipe thread seal- Test Of the Leak Detector ant to the 114-inch NPT tee and install on the hex nipple to accommodate both the vent tuba: and U.S. Environmental Protection Agei Araby (EPA)regulations re- To the snap tap. quire annual verification of operation of leak detector. To e. the snly ap to classified non-toxic pipe thread heal- assure maintenance of leak detection capability, Red Jacket ant to the threads UL-classified non-toxic NPT red heal-gree requires that operation of the mechanical leak detector be elbow vent tube fitting and install in the a co. verified by testing upon start-up and that testing of the leak f. Apply a UL-classified non-toxic pipe thread seal- detector be performed routinely at least annually. ant to the threads of the 1/4-inch NPT straight vent tube fitting and install in the leak detector • Teat detectors options for mechanical vent opening in the cap of the leak detector. Engileak neering a ering s ep rts,expPJ20 an Red J21.The g. Install the vent tubing into both fittings and Engineering Reports, Conner ors allow Red Jacket Snap Tap Connectors allow tighten. the FX2V/FX2DV leak detector to be tested h. To install snap tap connectors in FX2V/f'X2DV with the FXV Snap Tap Tester as an op- models, apply a UL-classified non-toxic pipe tion to the above test methods. See Red thread sealant to the snap tap connectors and Jacket lite'ratur3 #042-111.1 for test in. install one in the body of the FXV lean detector structions using Snap Tap Connectors. andtheother inthe tee attached tothe hex-.fipple 11. The top cover on the Red Jacket leak detector is attached to the 45-degree elbow installed in the tank test port of the packer. On 6-inch Big-Flo designed to accommodate arealingwire which can be applications,install the two snap tap connectors used to discourage tampering or the unauthorized -one inthe body ofthe FXV leak detector anIone removal of leak detector. (See Figure 2). in the riser/flange assembly. i. Attach and crimp loop of the retaining tether 11110,70M It should be noted that if the dispensing around the Snap Tap threads. system(the soleraid valve and the nozzle) is opened previous to the completion of j. Replace the caps over the quick-connectcou- the line test, the FXV Series will detect plings and tighten snugly. this opening as a leak and restricted flow DO NOT overtighten. will result. Closing of the nozzle(s)for a period of time adequate to allow comple- ® see technical bulletin#042.111.1 for use tion of the line test will allow the leak of Snap Tap Connector Assembly. detector to open.Once+opened,full pump flow can be providled. 7. Connect power to pump at the(oad center. 8. Clear remaining fir lrrom syste(n as follow&. a. Turn on dispenser that is farthest from tho leak FX2V/FX2DV TETHERED detector but do not open nozzle.Wait a or 5 CAP i minutes or more. Look for leaks on parts worked on. b. Shut off the pump and allow it to stand four or SNAP TAP --450 ELBOW five minutes. Then start the pump again and open the nozzle farthest from the leaf:detector. O C. Continue to dispense enough gasoline,about 20 to 30 gallons(76 to 114 liters),to pump ALL air Figure 1 from the system. y p - SEALING WIRE 1/4-INCH ❑Marley Pump (provided by contractor) .�� T-FITTING A U010 o rM canoar e1 7401 W. 129 St.•Overland Park, KS 66213.913.498-5700 � o Marley Pump reserves the right to make design Improvements and � n ENT TUBE pricing modifications as necessary and without notice. 01994 Marley Pump Primed in USA Figure 2