COMPLIANCE INFO_1986-2008 - Laserfiche WebLink

Home Browse Search

F VEEDER-ROOT • � _ SUMP SENSOR INSTALLATION INSTRUCTIONS IMPORTANT! . THIS MANUAL REQUIRES ALL PRELIMINARY SITE PREPARATION IS COMPLETED, AND THAT FIELD WIRING FROM THE MONITOR TO THE SENSOR JUNCTION BOX IS IN PLACE, IT CONTAINS INSTALLATION AND WIRING PROCEDURES FOR THE INSTALLATION OR REPLACEMENT OF A SUMP SENSOR SWITCH ONLY! FOR NEW INSTALLATIONS, REFER TO THE APPLICABLE "SITE PREPARATION AND INSTALLATION INSTRUCTIONS"MANUAL PROVIDED WITH THE SYSTEM AND LISTED IN SECTION I.A.1 OF THIS MANUAL. SECTION L INTRODUCTION 3. Risk of loss, or damage to merchandise remains with the buyer. It is the buyer's responsibility to file a claim with A. GENERAL the carrier involved. 1. This manual contains installation procedures for-the 4. Immediately advise your Veeder-Root representative, installation or replacement of Veeder-Root Sump Sensor, distributor,or the factory so that we may assist you. Part No. 794390-205, in an ILS-250 Interstitial Leak Sensor System, TLS-250i Four-Tank (Direct-Connect) Inventory C. RETURN SHIPPING. All shipments of Veeder-Root Monitor and Interstitial Leak Sensor System, or TLS7250i products must be prepaid. If the sump sensor is damaged, Eight-Tank (Indirect-Connect) Inventory Monitor, Leak return it in the original shipping container with shock Detect and Interstitial Leak Sensor System, ILS-350 absorbing material provided. Veeder-Root will accept no Compliance Console UST Monitoring System, and TLS-350 liability for.damage caused by improper packing. Address UST Monitoring System designed and manufactured by the shipment to Veeder-Root Co., 125 Powder Forest Drive, Viceder-Root Company. This manual assumes all Simsbury, Connecticut 06070-2003. preliminary site preparation is completed, and that field wiring from the monitor to the sensor junction box is in SECTION H.''PIPING SUMP SENSOR place. INSTALLATION If site preparation is necessary, refer to the appropriate The sump sensor comes with the following hardware Veeder-Root Site Preparation and Installation Instructions: necessary to mount it within the piping sump: ILS-250, Manual No. 576013-727; TLS-250i Four-Tank (Direct-Connect)System,Manual No.576013-579;TLS-2501 1 - PVC Mounting Sleeve Eight-Tank (Indirect-Connect)System,Manual No. 576013- 1 - ,aluminum 900 Mounting Bracket 577; IIS-350, Manual No. 576013-773; or TLS-350,Manual 1 - Cord Grip No.576013-622;or contactyour Veeder-Root representative 2 - #6-20 (.312" long) Sheet Metal Screws for assistance. ` 2. When a vertical bar I appears adjacent to text or A. GENERAL. The sump sensor can be. mounted either of illustrations, information has been added or changed at the two ways: on .the sensor junction box using the mounting last revision date. bracket and sleeve supplied (Figure 1); or,by cementing the B. DAMAGE CLAIMS PVC mounting sleeve directly to the side of a fiberglass T containment sump `(Figure 4). I. Thoroughly examine all components and units as soon as received. If damaged, write a complete and detailed Before you insiall The sump sensor, there are several description of the damage on the face of the freight bill. important requirements to consider: Have the carrier's agent sign the description. 1. The sump sensor must'be positioned as close to the NOTE: Insist that the carrier's agent verify the containment sump outer wallas possible. III inspection and sign the description. ; 2. The sump sensor pmust be mounted in a true vertical position to ensure proper operation of the float switch contained inside. 2. Immediately notify the delivering carrier of damage or - f loss. This notification may be given either in person or by 3. There must be at least one inch of clearance between the telephone. Written confirmation must be mailed within 48 bottom of the mounting sleeve and the base of the sump. hours. Railroads and motor carriers are understandably reluctant to make adjustments for damaged merchandise 4. When installed,the sump sensor must-rest on the base of unless inspected and reported promptly. the sump. ' 2