My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
INSTALL_1998
EnvironmentalHealth
>
EHD Program Facility Records by Street Name
>
H
>
HARLAN
>
15600
>
2300 - Underground Storage Tank Program
>
PR0231585
>
INSTALL_1998
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
4/28/2021 11:18:19 AM
Creation date
11/8/2018 10:22:28 AM
Metadata
Fields
Template:
EHD - Public
ProgramCode
2300 - Underground Storage Tank Program
File Section
INSTALL
FileName_PostFix
1998
RECORD_ID
PR0231585
PE
2361
FACILITY_ID
FA0000174
FACILITY_NAME
JOES TRAVEL PLAZA
STREET_NUMBER
15600
Direction
S
STREET_NAME
HARLAN
STREET_TYPE
RD
City
LATHROP
Zip
95330
APN
19620079
CURRENT_STATUS
01
SITE_LOCATION
15600 S HARLAN RD
P_LOCATION
07
P_DISTRICT
003
QC Status
Approved
Supplemental fields
FilePath
\MIGRATIONS3\H\HARLAN\15600\PR0231585\INSTALL 1998.PDF
QuestysFileName
INSTALL 1998
QuestysRecordDate
12/20/2017 9:22:38 PM
QuestysRecordID
3752004
QuestysRecordType
12
QuestysStateID
1
Tags
EHD - Public
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
240
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
GILBA <br /> Y-,ZOBE INSTALLATION INSTRUCTI� �illbvrco <br /> M�NNN el. <br /> 1 NMOLE <br /> • t „ , IF. <br /> r11 OR eEeR'n TO <br /> EU GRP SEALS <br /> At.NEvvtl <br /> SUvvLI O WITH PROBE <br /> MAGNET •'1 <br /> IN TOP MAGNET <br /> I IN TOP vrtArrtRr000P <br /> nwCrION env vein <br /> .x WCXxvi rx05 <br /> SGOT SPP Relic wcN <br /> =1 SERI <br /> ER NiIF <br /> SPEC <br /> le-NIN <br /> SEE SAAAGNtA <br /> •NOiE "Ca. Owrtn <br /> 1 R15ER DIMENSION ROBE <br /> SXOULO Be IE'TO <br /> LXE eOiiON Of L CO'A P�RPE <br /> FUEL FLOAT yr(L IB FLOAT TXERISER CAP SLXEWLEW <br /> ASSEMBLY MOUNTING TUBE <br /> Figure 10. Probe Assembly for Products NOT Requiring Water <br /> Measurement (4" Installation Kit) <br /> -MAONETOSTRICTwE <br /> PROBE <br /> E. PROBE INSTALLATION <br /> Install each probe as follows (see Figure 11, "Magneto- <br /> strictive Probe Installation Requirements"): <br /> Hob:dianetetdieminimumch Me ionic lelank <br /> WARNING: TO AVOID ELECTRICAL (ieample: eSnot me.M la all use,an W <br /> (Example:a tra Be.tone will i use,an d <br /> SHOCK WHICH COULD KILL YOU, BE intha TN,Pipe.IDOeR naastwill Ee ltile 6-IOge, <br /> SURE AC POWER TO THE MONITOR IS tMniMminmPumin ortlelrtoprovi0e RxHR1 <br /> OFF DURING INSTALLATION. Figure 11. Magnetostrictive Probe Installation Requirements <br /> 6. Carefully lower probe into the riser pipe until the boot <br /> rests on the bottom of the tank. <br /> CAUTION: DO NOT ALLOW PROBE TO FREE- <br /> 1. Turn OFF power to the monitoring system. {�, FALL AND/OR SHARPLY IMPACT THE BOT- <br /> TOM OF THE TANK. SHOCK TO THE PROBE <br /> 2. Make sure any liquid other than the product to be dis- FOOT WILL RESULT IN SEVERE DAMAGE. <br /> pensed has been pumped out of the tank. <br /> 7. Feed the two-wire probe cable up through the riser pipe <br /> 3. Be sure there is no sludge in the bottom of the tank. cap bushing and in through the junction box bushing. Leave <br /> Sludge can interfere with proper operation of the water float. enough slack in the table between the tap and junction box <br /> CAUTION: HANDLE PROBES CAREFULLY! to allow the cap to easily reach the riser pipe. In addition, <br /> STRIKING OR DROPPING PROBE WILL RESULT leave enough slack under the riser cap to allow the probe to <br /> IN LOSS OF CALIBRATION AND COULD CAUSE rest on the bottom of the tank. <br /> PERMANENT DAMAGE. CAUTION: WHEN USING SHIELDED CABLE <br /> FOR PROBE WIRING,THE DRAIN WIRE FROM <br /> 4. Attach the probe cable connector to the mating plug on 10 THE SHIELDED CABLE MUST BE CONNECTED <br /> the top of the probe. Be sure the connector is attached TO THE GROUND LUG IN THE CONSOLE'S <br /> securely by hand tightening the locking ring. INTRINSICALLY SAFE AREA. <br /> NOTE: The use of the strain relief chain is no longer g, For Tank Monitor 2 Series,Tank Monitor 3 Series Four- <br /> required. Tank and EMC systems,using wiring nuts,connect the wires <br /> 5. Place floats at bottom of probe before standing the probe from the probe cable to the probe field wires in the junction <br /> on end. box (see Figure 12). Be sure to observe proper polarity <br /> between the probe and monitor wiring during installation. <br /> CAUTION: HANDLE PROBES CAREFULLY! The conduit must be properly sealed in accordance with the <br /> STRIKINGOR DROPPING PROBE WILL RESULT National Electrical Code (NFPA 70) and the Automotive <br /> IN LOSS OF CALIBRATION AND COULD CAUSE and Marine Service Station Code (NFPA 30A) since they <br /> PERMANENT DAMAGE. pass from a Class 1, Division I or Division II area into a non- <br /> hazardous area. <br /> 5 <br />
The URL can be used to link to this page
Your browser does not support the video tag.