My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
INSTALL_1998
EnvironmentalHealth
>
EHD Program Facility Records by Street Name
>
H
>
HARLAN
>
15600
>
2300 - Underground Storage Tank Program
>
PR0231585
>
INSTALL_1998
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
4/28/2021 11:18:19 AM
Creation date
11/8/2018 10:22:28 AM
Metadata
Fields
Template:
EHD - Public
ProgramCode
2300 - Underground Storage Tank Program
File Section
INSTALL
FileName_PostFix
1998
RECORD_ID
PR0231585
PE
2361
FACILITY_ID
FA0000174
FACILITY_NAME
JOES TRAVEL PLAZA
STREET_NUMBER
15600
Direction
S
STREET_NAME
HARLAN
STREET_TYPE
RD
City
LATHROP
Zip
95330
APN
19620079
CURRENT_STATUS
01
SITE_LOCATION
15600 S HARLAN RD
P_LOCATION
07
P_DISTRICT
003
QC Status
Approved
Supplemental fields
FilePath
\MIGRATIONS3\H\HARLAN\15600\PR0231585\INSTALL 1998.PDF
QuestysFileName
INSTALL 1998
QuestysRecordDate
12/20/2017 9:22:38 PM
QuestysRecordID
3752004
QuestysRecordType
12
QuestysStateID
1
Tags
EHD - Public
Jump to thumbnail
< previous set
next set >
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
240
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
G I ARCO <br /> �11I�OG�1"DO PRWE INSTALLATION INSTRUCT[O. S <br /> 6. Slide the boot onto the end of the probe,and turn until <br /> �IWARNING: USED OIL MAY CONTAIN the boot's bosses snap into the probe detents. (Refer to <br /> TOXIC SUBSTANCES. AVOID SKIN CON- Figure 8 or 9, or 10.) <br /> TACT WITH OIL WHEN HANDLING THE CAUTION: FAILURE TO SNAP THE BOOT INTO <br /> PROBES. THE PROBE DETENTS COULD RESULT IN THE <br /> V LOSS OF THE BOOT AND FLOATS WITHIN THE <br /> TANK. <br /> I NOTE: Only the water float mounting tube will be <br /> used in place of the water float assembly for the <br /> products where water measurement is not possible. <br /> (See Figure 10). <br /> MAGNET BALLAST RING <br /> INITOP (IF REQUIRED) <br /> 3. Gently slide the fuel float onto the probe shaft, magnet- <br /> side up. The float should move freely on the probe shaft. BOOT <br /> (See Figure 8 or 9, "Probe Assembly for Products Requiring <br /> Water Measurement," or Figure 10, "Probe Assembly for <br /> Products NOT Requiring Water Measurement.") <br /> MAGNET <br /> NOTE: The fuel float must be placed magnet-side up FUEL FLOAT ATOP WATER FLOAT <br /> II to effectively measure fuel. The magnet is located in ASSEMBLY ASSEMBLY <br /> Q <br /> the narrow Cylindrical end of the fuel float. The wider <br /> end of the float is marked "BOTTOM THIS SIDE <br /> DOWN". Figure ti. Probe Assembly for Products Requiring Water <br /> BE SURE TO SLIDE THE MAGNET END OF THE Measurement (4" Installation Kit) <br /> FLOAT ON FIRST! 7. Gently slide the floats to the bottom of the probe shaft. <br /> I NOTE: When using 2" floats with a TM System or CAUTION: FLOATS MUST BE AT BOTTOM OF <br /> EMC System with Version 2 software, 2.25" must be �j PROBE SHAFT BEFORE STANDING THE <br /> = added to the tank tilt value during System Setup. YY PROBE UPRIGHT. SIGNIFICANT FUEL ANI* <br /> WATER FLOAT DAMAGE WILL OCCUR IF <br /> OR FLOATS ARE ALLOWEDTO FALL FREELYDOWN <br /> PROBE SHAFT. <br /> When using 2" floats with an EMC with Version 3 or <br /> higher software, be sure to choose 2" float during In- <br /> Tank Setup. <br /> CAUTION: INSTALL THE FLOATS MAGNET- <br /> SIDE UP. IF THEY ARE INSTALLED INCOR- NFRE D) <br /> BF REOUWEO) LI RECTLY,INCORRECT FUEL HEIGHT AND WA- <br /> TER HEIGHT READINGS WILL RESULT. B <br /> CAUTION: WHEN SLIDING THE FLOAT ONTO <br /> THE PROBE SHAFT, BE CAREFUL NOT TO / <br /> Y BREAK ANY OF THE MAGNET RETENTION / FUEL FLOAT <br /> FINGERS. THIS COULD RESULT IN IMPROPER ASSEMBLY <br /> MOVEMENT OF THE FLOAT AND INACCU- MAGNET <br /> WATER FLOAT W TOP <br /> RATE READINGS. ASSEMBLY <br /> 4. Gently slide the water float mounting tube onto the probe Figure 9. Probe Assembly for Products Requiring Water <br /> shaft, magnet-end first, ballast-end last. The float should Measurement (2" Installation Kit) <br /> move freely on the probe shaft. (Refer to Figure 8 or 9,or <br /> 10.) <br /> CAUTION: WHEN SLIDING THE FLOAT ONTO <br /> ICY THE PROBE SHAFT, BE CAREFUL NOT TO <br /> Y BREAK ANY OF THE MAGNET RETENTION <br /> FINGERS. THIS COULD RESULT IN IMPROPER <br /> MOVEMENT OF THE FLOAT AND INACCU- <br /> RATE READINGS. <br /> 4 <br />
The URL can be used to link to this page
Your browser does not support the video tag.