WORK PLANS - Laserfiche WebLink

Home Browse Search

ADA/CBC Notes ADA/CBC Notes (Continued) ADA/CBC Notes (Continued) ADA/CBC Notes (Continued) A.APPLICATION AND ADMINISTRATION C.ACCESSIBLE ROUTES 38. Thresholds, if provided at doorways,shall be 1/2 inch high maximum. Raised thresholds and changes in 86. The clear width of curb ramp runs(excluding any flared sides), blended transitions,and turning spaces shall � level at doorways shall comply with 11 B-302 Floor or Ground Surfaces and 11 B-303 Changes in Level. be 48 inches minimum.§118-406.5.2 1. When alterations or additions are made to existing buildings or facilities,an accessible path of travel to the GENERAL §11B-404.2.4.5. 87. Landings shall be provided at the tops of curb ramps and blended transitions (parallel curb ramps shall not be specific area of alteration or addition shall be provided unless otherwise exempt.§11 B-202.4 39. Handles,pulls, latches, locks, and other operable parts on doors and gates shall comply with 11 B-309.4 required to comply).The landing clear length shall be.at least as wide as the curb ramp, excluding any flared - 2. Primary accessible path of travel shall include a primary entrance to the building or facility;toilet and bathing 1. At least one accessible route shall be provided within the site from accessible parking spaces and accessible Operation.Operable parts of such hardware shall be 34 inches minimum and 44 inches maximum above the sides,or the blended transition leading to the landing.The slope of the landing in all directions shall be 1:48 � facilities serving the area;drinking fountains serving the area;public telephones serving the area,and signs. passenger loading zones;public streets and sidewalks;and public transportation stops to the accessible finish floor or ground.Where sliding doors are in the fully open position, operating hardware shall be exposed (2.083%) maximum.§11 B-406.5.3 §11B-202.4 building or facility entrance they serve.Where more than one route is provided, all routes must be accessible. and usable from both sides. §71 B-404.2.7 88. Grade breaks at the top and bottom of curb ramp runs shall be perpendicular to the direction of the ramp run. 3. When the adjusted construction cost is less than or equal to the current valuation threshold ($143,863),the §11 B-206.2.1 (See exceptions) 40. The force for pushing or pulling open a door or gate other than fire doors shall be as follows: Grade breaks shall not be permitted on the surface of ramp runs and turning spaces. Surface slopes that cost of compliance with the primary accessible path of travel requirements is limited to 20 percent of the 2. At least one accessible route shall connect accessible buildings, accessible facilities, accessible elements, a. Interior hinged doors and gates: 5 pounds maximum. meet at grade breaks shall be flush. §11 B-406.5.3 adjusted construction cost of alterations,structural repairs or additions presently planned and those during and accessible spaces that are on the same site. §11 B-206.2.2(Sea exceptions) b. Sliding or folding doom:5 pounds maximum. 89. The cross slope of curb ramps and blended transitions shall be 1:48 (2.083%) maximum.§116.406.5.7 the preceding three-year period.§ii B-202.4 3. At least one accessible route shall connect each story and mezzanine in multi-story buildings and facilities. c. Required fire doors:the minimum opening force allowable by the appropriate administrative authority, 90. Counter slopes of adjoining gutters and road surfaces immediately adjacent to and within 24 inches of the 4. Adjusted construction cost of alterations,structural repairs or additions does not include the cost of §11 B-206.2.3(See exceptions) not to exceed 15 pounds. curb ramp shall not be steeper than 1:20 (5%).The adjacent surfaces at transitions at curb ramps to walks, alterations to path of travel elements.§11 B-202.4 4. In new construction of buildings where elevators are required by 11 B-206.2.3 Multi-Story Buildings and d. Exterior hinged doors:5 pounds maximum. gutters, and streets shall be at the same level.§11 B-406.5.8 ©zon sTnasucrc3 COFFEE COMPANY 5. In choosing which accessible elements to provide, priority should be given to those elements that will Facilities,and which exceed 10,000 square feet on any floor,an accessible means of vertical access via ramp, 41. Swinging door and gate surfaces within 10 inches of the finish floor or ground measured vertically shall have 91. The bottom of diagonal curb ramps shall have a clear space 48 inches minimum outside active traffic lanes provide the greatest access in the following order:(1)an accessible entrance;(2)an accessible route to the elevator or lift shall be provided within 200 feet of travel of each stair and each escalator.§11 B-206.2.3.2 a smooth surface on the push side extending the full width of the door or gate. Parts creating horizontal or of the roadway. Diagonal curb ramps provided at marked crossings shall provide the 48 inches minimum rn alteredarea;(3)atleastoneaccessiblerestroomforeachsex;(4)accessibletelephones; (5) accessible 5. In existing buildings that exceed 10,000 square feet on any floor and in which elevators are required by vertical joints in these surfaces shall be within l/16inch ofthe same plane asthe other and befree ofsharp clear space within the markings. §11B-406.5.9 STARBUCKS COFFEE drinking fountains;and (6)when passible,additional accessible elements such as parking,storage and 11 B-206.2.3 Multi-Story Buildings and Facilities,whenever a newly constructed means of vertical access is or abrasive edges.Cavities created by added kick plates shall be capped.§11 B-404.2.10 92. Curb ramps and blended transitions shall have detectable warnings complying with 11 B-705 Detectable alarms.§11 B-202.4 provided via stairs or an escalator,an accessible means of vertical access via ramp, elevator or lift shall be Warnings.§11 B-406.5.12 COMPANY = 6. Alterations to a qualified historic building or facility shall comply with Chapter 11 B unless it will threaten or provided within 200 feet of travel of each new stair or escalator. §11 B-206.2.3.2 RAMPS 93. Raised islands in crossings shall be cut through level with the street or have curb ramps at both sides.The 2401 UTAH AVENUE SOUTH c destroy the historical significance or character-defining features of the building or property. In those cases, 6. At least one accessible route shall connect accessible building or facility entrances with all accessible spaces clear width of the accessible route at islands shall be 60 inches wide minimum.Where curb ramps are W alternative provisions shall be applied on an item-by-item or case-by-case basis with sufficient written and elements within the building or facility, including mezzanines,which are otherwise connected by a 42. Provide ramp details, including slope, landings, and handrails. provided,they shall comply with 11 B-406 Curb Ramps, Blended Transitions and Islands. Landings complying SEATTLE, WASHINGTON 98134 -p documentation.§11 B-202.5,SHBC 8.602 circulation path. §71 B-206.2.4(See exceptions 1 through 7) 43. Ramp runs shall have a running slope not steeper than 1:12(8.33%).§11 B-005.2 with 11 B-406.5.3 Landings and the accessible route shall be permitted to overlap. Islands shall have (206) 318-1575 W 7. Public accommodations shall maintain in operable working condition those features of facilities and 7. Accessible routes shall coincide with or be located in the same area as general circulation paths. Where 44. Cross slope of ramp runs shall not be steeper than 1:48 (2.083%). §71 B-405.3 detectable warnings complying with 11 B-705 Detectable Warnings and Detectable Directional Texture. that are required to be accessible to and useable b persons with disabilities. Isolated or circulation paths are interior, required accessible routes shall also be interior;An accessible route shall not 45. Floor or round surfaces of ram runs shall cam with 11 B-302 Floor or Ground Surfaces. Changes in (r equipmentq y p p q g p comply g §11 B-406.6, Figure 116.406.6 THESE DRAWINGS AND SPECIFICATIONS ARE t temporary interruptions in service or accessibility due to maintenance or repairs shall be permitted. pass through kitchens, storage rooms, restrooms,closets or other spaces used for similar purposes,except level other than the running slope and cross slope are not permitted on ramp runs.§1116-405.4 CONFIDENTIAL AND SHALL REMAIN THE SOLE 2 §11B-108 as permitted by Chapter 10.§11 B-206.3 46. The clear width of a ramp run shall be 48 inches minimum.§11B-405.5 D.GENERAL SITE AND BUILDING ELEMENTS PROPERTY OF STARBUCKS CORPORATION, Q 47. The rise for any ramp run shall be 30 inches maximum. §11B-405.6 WHICH IS THE OWNER OF THE COPYRIGHT IN r�L B.BUILDING BLOCK EMPLOYEE WORKSTATIONS 48. Ramps shall have landings at the top and the bottom of each ramp run. §11B-405.7 PARKING SPACES THIS WORK. THEY SHALL NOT BE 0 49. Landings shall comply with 11 B-302 Floor or Ground Surfaces. Changes in level are not permitted. REPRODUCED (IN WHOLE OR IN PART),SHARED o FLOOR OR GROUND SURFACES 8. Employee workstations shall be on an accessible route complying with Division 4.Spaces and elements within §71 B-407.1 1. Where parking spaces are provided,accessible parking spaces shall be provided in number and kind WITH THIRD PARTIES OR USED IN ANY MANNER 00 employee workstations shall only be required to comply with Sections 11 B-207.1, 11 B-215.3, 11 B-302, 50. The landing clear width shall be at least as wide as the widest ramp run leading to the landing.§11 B-405.7.2 required per Section 11 B-208 Parking Spaces.§11 B-208.1 ON OTHER PROJECTS OR EXTENSIONS TO THIS 1. Floor and ground surfaces shall be stable,firm,and slip resistant.§11 B-302.1 11 B-303, and 11 B-404.2.3.Common use circulation paths within employee workstations shall comply with 51. Top landings shall be 60 inches wide minimum.§118.405.7.2.1 2. Provide 1 accessible parking spaces as required by Table 11 B-208.2.§11 B-208.2(Sea exceptions) PROJECT WITHOUT THE PRIOR WRITTEN 0 2. Carpet or carpet tile shall be secure) attached and shall have a firm cushion, ad, or backingor no cushion Section 11 B-206.2.8. 11B-203.9 52. The landingclear length shall be 60 inches low minimum. 11B-405.7.3 3. Provide accessible spaces for each parking facility (parking lots and parking structures The number of CONSENT OF STARBUCKS CORPORATION. y p § g g § p p s ty(p g p g ) THESE DRAWINGS AND SPECIFICATIONS ARE c+1 or pad. Carpet or carpet file shall have a level loop,textured loop, level cut pile, or level cut/uncut pile 53. Bottom landings shall extend 72 inches minimum in the direction of ramp run. §71 B-405.7.3.1 parking spaces required to be accessible is to be calculated separately for each parking facility;the required S9 texture. Pile height shall be 12 inch maximum.§1116-302.2, Figure 1113-302.2 INTENDED TO EXPRESS DESIGN INTENT FOR A DETECTABLE WARNINGS AND DETECTABLE DIRECTIONAL TEXTURE 54. Ramps that change direction between runs at landings shall have a clear landing 60 inches minimum by 72 number is not based on the total number of parking spaces provided in all of the parking facilities provided on Z inches minimum in the direction of downward travel from the upper ramp run.§118.405.7.4 site. §11 B-208 PROTOTYPICAL STARBUCKS STORE(WHICH IS a) CHANGES IN LEVEL 9. Curb ramps shall have detectable warnings that extend 36 inches in the direction of travel for the full width of 55. Where doorways are located adjacent to a ramp landing, maneuvering clearances required by 118404.2.4 4. Ten percent of patient and visitor parking spaces provided to serve hospital outpatient facilities, and free- SUBJECT TO CHANGE AT ANYTIME)AND DO = the ramp run less than 2 inches maximum on each side,excluding any flared sides.§11 B-247.1.2.2, and 11 B-404.3.2 shall be permitted to overlap the required landing area. Doors,when fully open,shall not standing buildings providing outpatient clinical services of a hospital,shall comply with Section 11 B-502 NOT REFLECT ACTUAL SITE CONDITIONS. 3. Vertical changes in level for floor or ground surfaces may be 1,4 inch high maximum and without edge §1118.705.1.2.2 reduce the required ramp landing width by more than 3 inches. Doors, in any position,shall not reduce the Parking Spaces.§1113.208.2.1 NEITHER PARTY SHALL HAVE ANY OBLIGATION o NOR LIABILITY TO THE OTHER EXCEPT STATED treatment.Changes in level greater than 1�4 inch and not exceeding 12 inch in height shall be beveled 10. On perpendicular curb ramps,detectable warnings shall be located se the edge nearest the curb is 6 to 8 minimum dimension of the ramp landing to less than 42 inches. §118.405.7.5 5. Twenty percent of patient and visitor parking spaces provided[o serve rehabilitation facilities specializing in t"1 with a slope not steeper than 1:2.§11 B-303,Figures 11 B-303.2&11B-303.3 inches from the line at the face of the curb marking the transition between the curb and the gutter, street or 56. Ramp runs shall have compliant handrails per l l B-505 Handrails.§111 B-405.8 treating conditions that affect mobility and outpatient physical therapy facilities shall comply with Section ABOVE) UNTIL A WRITTEN AGREEMENT IS L 4. Changes in level greater than 12 inch in height shall be ramped and shall comply with the requirements of highway.§11 B-247.1.2.2,§11 B-705.1.2.2 57. Edge protection complying with 11 B-405.9.2 Curb or Barrier shall be provided on each side of ramp runs and 11B-502 Parking Spaces.§11 B-208.2.2 FULLY EXECUTED BY BOTH PARTIES. 11 B-405 Ramps or 11 B-406 Curb Ramps as applicable. §118.303 11. On parallel curb ramps,detectable warnings shall be placed on the turning space at the flush transition at each side of ramp landings.§11 B-405.9(Sea exceptions) 6. One in every six or fraction of six parking spaces required by Section 11B-208.2 Minimum Number,but not Q5. Abrupt changes in level exceeding 4 inches in a vertical dimension between walks, sidewalks or other between street and sidewalk. Detectable warnings shall extend the full width of the turning space at the flush 58. A curb, 2 inches high minimum,or barrier shall be provided that prevents the passage of a 4 inch diameter less than one,shall be served by an access aisle 96 inches wide minimum placed on the side opposite the STARBUCKS TEMPLATE VERSION 12017.05.18 pedestrian ways and adjacent surfaces or features shall be identified by warning curbs at least 6 inches in transition between the street and the sidewalk less than 2 inches maximum on each side.§11 B-247.1.2.2, sphere,where any portion of the sphere is within 4 inches of the finish floor or ground surface.To prevent driver's side when the vehicle is going forward into the parking space and shall be designated'arvan 0 height above the walk or sidewalk surface or by guards or handrails with a guide rail centered 2 inches §11 B-705.1.2.2, Figure 11 B-406.3.2 wheel entrapment,the curb or barrier shall provide a continuous and uninterrupted barrier along the length of accessible". All such spaces may be grouped on one level of a parking structure.§11 B-208.2.4,11 B-502, 0 minimum and 4 inches maximum above the surface of the walk or sidewalk.These requirements do not 12. Islands or cut-through medians 96 inches or longer in length in the direction of pedestrian travel shall have the ramp.§1118.405.9.2 Fig 11 B-502,118.502.3,&118.502.3.3 o apply between a walk or sidewalk and an adjacent street or driveway. §716.303.5 detectable warnings that are 36 inches minimum in depth extending the full width of the pedestrian path or cut- 59. Landings subject to wet conditions shall be designed to prevent the accumulation of water. §118-405.10 7. Accessible parking spaces complying with Section 11 B-502 Parking Spaces serving a particular building or mm M through less than 2 inches maximum on each side placed at the edges of the pedestrian island or cut-through facility shall be located on the shortest accessible route of travel from adjacent parking to an accessible 5-11 M TURNING SPACE median, and separated by 24 inches minimum of walking surface without detectable warnings. HANDRAILS entrance(as near as practical to an accessible entrance).§11 B-208.3.1 0 §11 B-247.1.2.3, §11 B-705.1.2.3 8. In buildings with multiple accessible entrances with adjacent parking,accessible parking spaces complying 5858 Wilshire Blvd #200 T: 32 .954.8996 C 6. Circular turning spaces shall be a space of 60 inches diameter minimum and may include knee and toe 13. Walks that cross or adjoin a route provided for vehicular traffic,such as in a street,driveway,or parking 60. Handrails shall be provided on both sides of stairs and ramps.§11 B-505.2 with Section 11 B-502 Parking Spaces shall be dispersed and located closest to the accessible entrances. d 3 E clearance complyingwith 11B-306 Knee and Toe Clearance. 11 B-304.3.1 facility,shall be separated b detectable warnings,curbs,railings or other elements between pedestrian areas E § Y P Y 9 9 P 61. Handrails shall be continuous within the Lull length of each stair flight or ramp run. Inside handrails on §118.208.3.1 Los Angeles, CA 90036 F: 323.954.8965 7. T-Shaped turning spaces shall be a T-shaped space within a 60 inch square minimum with arms and base and vehicular areas.§202,§11 B-247.1.2.5,§11 B-705.1.2.5 switchback or dogleg stairs and ramps shall be continuous between flights or runs.§11 B-505.3 9. In parking facilities that do not serve a particular building or facility, accessible parking spaces complying with p 3fi inches wide minimum. Each arm of the T shall be clear of obstructions 12 inches minimum in each 14. Detectable warnings provided to separate walks that cross or adjoin a route provided for vehicular traffic, such 62. Top of gripping surfaces of handrails shall be 34 inches minimum and 38 inches maximum vertically above Section 11 B-502 Parking Spaces shall be located on the shortest accessible route of travel to an accessible www.valerioinc.com • info@vaerioinc.com 0 direction and the base shall be clear of obstructions 24 inches minimum.§71 B-304.3.2, Figure 11 B-304.3.2 as in a street,driveway, or parking facility,shall be 36 inches in width and continuous at the boundary between walking surfaces, stair nosings,and ramp surfaces. Handrails shall be at a consistent height above walking pedestrian entrance of the parking facility.§11 B-208.3.1 C the pedestrian areas and vehicular areas.§202,§11 B-247.1.2.5,§11 B-705.1.2.5 surfaces, stair nosings, and ramp suriaces.§11 B-505.4 10. Dimension minimum 18-foot long car and van accessible parking space(s)and access aisle(s).§11B-502.2, ARCHITECT g KNEE AND TOE CLEARANCE 15. Provide detectable warning details showing compliance with the following: 63. Clearance between handrail gripping surfaces and adjacent surfaces shall be 1-1/2 inches minimum. Figures i1B-502.2 and 11 B-502.3 OF RECORD AIR? c a. Detectable warning surfaces at transit boarding platform edges,bus stops,hazardous vehicular Handrails may be located in a recess if the recess is 3 inches maximum deep and 18 inches minimum clear 11. Dimension minimum 9-foot width at accessible car parking space.§11 B-502.2, Fig.11 B-502.2 and Fig. �C0"o V- r./�. 8. For lavatories and built-in dining and work surfaces required to be accessible,toe clearance shall be areas, reflecting pools,and track crossings shall comply with Section 11 B-705.1.1.3.1. §11B-705.1.1.3 above the top of the handrail.§11 B-505.5 11B-502.3 W v 9„ provided that is 30 inches in width and 9 inches in het ht above the finish floor or round for a de depth of 19 b. Detectable warnin s at other locations shall com I with either Section 11 B-705.1.1.3.1 or Section LIC. 228 O tt P 9 9 P 9 comply 64. Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops 12. Dimension minimum 12-foot wide accessible van parking space with minimum 5-foot wide access aisle.Van t 2 ("� o inches minimum.§11 B-306.2.1 11 B-705.1.1.3.2.The material used to provide visual contrast shall be an integral part of the surface. or sides.The bottoms of handrail gripping surfaces shall not be obstructed for more than 20 percent of their parking spaces shall be permitted to be minimum 9 feet wide where access aisle is 8-foot wide minimum. a C 24226 H U 9. Toe clearance shall extend 19 inches maximum under lavatories for toilet and bathing facilities and 25 §1116-705.1.1.3 length.Where provided, horizontal projections shall occur 1. inches minimum below the bottom of the §11 B-502.2, Figures 11B-502.2 and 11 B-502.3 EXPIRES It inches maximum under other elements.§118.306.2.2 16. Detectable warningsurfaces shall be yellow and approximate FS 33538 of Federal Standard 595C. handrail gripping § 1 7a1 19 Q. Y apP g ppin surface. 11 B-505.6 13. Car and van stall access aisle shall be 5 foot wide minimum and shall adjoin an accessible route.Two `'�y �S 10. At lavatories in toilet and bathing facilities, knee clearance shall be provided that is 30 inches in width for a §11 B-705.1.1.3 65. Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1-1/4 inches parking spaces shall be permitted to share a common access aisle. §1IB-502.2,Figures 11 B-502.2 and 7Eor I'll M depth of 11 inches at 9 inches above the finish floor or ground and for a depth of 8 inches at 27 inches above 17. Detectable warning surfaces shall provide a 70 percent minimum visual contrast with adjacent walking minimum and 2 inches maximum. §11B-505.7.1 11B-502.3 M the finish floor or ground increasing to 29 inches high minimum above the finish floor or ground at the front surfaces. Contrast in percent shall be determined by: 66. Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches 14. Access aisles shall be marked with a blue painted borderline around their perimeter.The area within the blue !N edge of a counter with a built-in lavatory or at the front edge of a wall-mounted lavatory fixture. Contrast percent=tel-B2)/Btj x 100 where minimum and 6-1/4 inches maximum,and a cross-section dimension of 2-1/4 inches maximum. borderlines shall be marked with hatched lines a maximum of 36 inches on center in a color contrasting with M §11B-306.3.3, Figure 116-306.3(c) B1 =light reflectance value(LRV) of the lighter areas and §11 B-505.7.2 that of the aisle surface,preferably blue or white.The words"NO PARKING"shall be painted on the surface 01 11. At dining and work surfaces required to be accessible, knee clearance shall be provided that Is 30 inches in B2=light reflectance value(LRV) of the darker area 67. Handrail gripping surfaces shall extend beyond and in the same direction of stair flights and ramp runs in within each access aisle in white letters a minimum of 12 inches in height and located to be visible from the r- width at 27 inches above the finish floor or ground for a depth of at least 19 inches.§11 B-306.3. §11B-705.1.1.3.2(See exception) accordance with Section 11 B-505.10 Handrail Extensions.§11 B-505.10 adjacent vehicular way.Access aisle markings may extend beyond the minimum required length. N 68. In alterations,where the extension of the handrail in the direction of the stair flight or ramp run would create a §11 B-502.3.3, Figure 11 B-502.3.3 N PROTRUDING OBJECTS ENTRANCES hazard,the extension of the handrail may be turned 90 degrees from the direction of stair flight or ramp run. 15. Access aisles shall not overlap the vehicular way. Access aisles shall be permitted to be placed on either side §11 B-505.10 exception 3 of the parking space except for van parking spaces which shall have access aisles located on the passenger Z 12. Except for handrails,objects with leading edges more than 27 inches and less than 80 inches above the 18. Entrances shall be provided in accordance with 11 B-206.4 Entrances. Entrance doors,doorways,and gates 69. Ramp handrails shall extend horizontally above the landing for 12 inches minimum beyond the top and side of the parking spaces.§it B-502.3.4 M i D- finish floor or ground shall protrude no more than 4 inches horizontally into the circulation path. Handrails shall comply with 11 B-404 Doors, Doorways,and Gates and shall be on an accessible route complying with bottom of ramp runs. Extensions shall return to a wall,guard, or the landing surface, or shall be continuous to 16. Clearly show minimum vertical clearance of 8 feet 2 inches at accessible parking spaces and along at least [___ r VI may protrude 4-12 inches maximum.§11 B-307.2, Figure 11B-307.2 11B-402 Accessible Routes;(See exceptions).§11 B-206.4 the handrail of an adjacent ramp run.§11 B-505.10.1 one vehicle access route to such spaces from site entrances and exits. §71 B-502.5 C7 N M 13. Free-standing objects mounted on posts or pylons shall overhang circulation paths no more than 12 inches 19. All entrances and exterior ground-floor exits to buildings and facilities shall comply with 11 B-404 Doors, 70. At the top of a stair flight, handrails shall extend horizontally above the landing for 12 inches minimum 17. Parking space identification signs shall include the International Symbol of Accessibility complying with U000 when located from 27 to 80 inches above the finish floor or ground.§11 B-307.3, Figure 11B-307.3(a) Doorways, and Gates. §118.206.4.1 beginning directly above the first riser nosing. Extensions shall return to a wall,guard, or the landing surface, Section 11 B-703.7.2.1 International Symbol of Accessibility.§11 B-502.6, Figure 11 B-703.7.2.1 Q 0 14. Protruding objects shall not reduce the clear width required for accessible routes. §71 B-307.5 20. Where direct access is provided for pedestrians from a parking structure to a building or facility entrance, each or shall be continuous to the handrail of an adjacent stair flight. §11B-505.10.2 18. Signs identifying van parking spaces shall contain additional language or an additional sign with the LU # 15. Lowest edge of a sign or other obstruction,when mounted between posts or pylons separated with a clear direct access to the building or facility entrance shall comply with 11 B-404 Doors, Doorways,and Gates. 71. At the bottom of a stair flight,handrails shall extend at the slope of the stair flight for a horizontal distance designation "van accessible"Signs shall be 60 inches minimum above the finish floor or ground surface � M Q ar = LT t distance greater than 12 inches,shall be less than 27 inches or more than 80 inches above the finish floor or §11 B-206.4.2 equal to one tread depth beyond the last riser nosing. Such extension shall continue with a horizontal measured to the bottom of the sign.§71 B-502.6 U 0 ground. §118.307.3,Figure 11 B-307.3(6) 21. Direct connections to other facilities shall provide an accessible route complying with 11 B404 Doors, extension or shall be continuous to the handrail of an adjacent stair flight or shall return to a wall,guard, or 19. Parking identification signs shall be reflectorized with a minimum area of 70 square inches. §11 B-502.6.1 �x N 16. Vertical clearance shall be at least 80 inches high on circulation paths except at door closers and door stops, Doorways,and Gates from the point of connection to boarding platforms and all transportation system the walking surface.At the bottom of a stair flight,a horizontal extension of a handrail shall be 12 inches long 20. Additional language or an additional sign below the International Symbol of Accessibility shall state"Minimum W } which may be 78 inches minimum above the finish floor or ground. §1116.307.4 elements required to be accessible. Any elements provided to facilitate future direct connections shall be on an minimum and a height equal to that of the sloping portion of the handrail as measured above the stair Fine$250."§118-502.6.2 z M 17. Guardrails or other barriers with a leading edge located 27 inches maximum above the finish floor or ground accessible route connecting boarding platforms and all transportation system elements required to be nosings. Extension shall return to a wall,guard, or the landing surface, or shall be continuous to the handrail 21. A parking space identification sign shall be visible from each parking space. Signs shall be permanently = C7 I shall be provided where the vertical clearance on circulation paths is less than 80 inches high.§1IB-307.4, accessible.§11B-206.4.4.2(See exception) of an adjacent stair flight. §11B-505.10.3 posted either immediately adjacent to the parking space or within the projected parking space width at the I- �, Figure 11 B-307.4 head end of the parking space.Signs may also be permanently posted on a wall at the interior end of the Q uj LU Y 2 18. Where a guy support is used within either the width of a circulation path,a vertical guy brace, sidewalk guy TECHNICAL REQUIREMENTS FOR ACCESSIBLE ROUTES STAIRWAYS parking space. §718502.6.3 U) � U .o I or similar device shall be used to prevent a hazard or an overhead obstruction. §1116-307.4.1, Figure 22. Each accessible car and van space shall have surface identification complying with either of the following . . OM LU Q LU O C 11B-307.4.1 22. Accessible routes shall consist of one or more of the following components:walking surfaces with a running 72. A stair is defined as a change in elevation,consisting of one or more risers.§11 B-202 schemes:§11B-502.4 LU LL 0 W t slope not steeper than 1:20(5%),doorways, ramps,curb ramps excluding the flared sides,elevators,and 73. All steps on a flight of stairs shall have uniform riser heights and uniform tread depths. Risers shall be 4 a.The parking space shall be marked with an International Symbol of Accessibility(ISA)complying with Q 0 m REACH RANGES platform lifts.§11B-402.2 inches high minimum and 7 inches high maximum.Treads shall be 11 inches deep minimum. Curved Section 11 B-703.7.2.1 ISA in white on a blue background a minimum 36 inches wide by 36 inches high.The Z T Q Q O 23. The running slope of walking surfaces shall not be steeper than 1:20(5%).The cross slope of walking stairways with winder treads are permitted at stairs which are not part of a required means of egress. (See centerline of the ISA shall be a maximum of 6 inches from the centerline of the parking space, its sides H 2 H C� H IL 19. Electrical controls and switches intended to be used by the occupant of a room or area to control lighting and surfaces shall not be steeper than 1:48 (2.083%).§11 B-403.3 exception)§11 B-504.2 parallel to the length of the parking space and its lower corner at, or lower side aligned with,the end of the 0 U U Z 0 sI receptacle outlets, appliances or cooling,heating and ventilating equipment shall be located within allowable 24. Except at turns or passing spaces,the clear width of walking surfaces shall be 36 inches minimum. 74. Open risers are not permitted. §11B-504.3(See exceptions) parking space length. §718502.6.4.1 LU M ' Ln O Q MCT)reach ranges. Low reach shall be measured to the bottom of the outlet box and high reach shall be §11 B-403.5.1 75. Interior stairs shall have the upper approach and lower tread marked by a stripe providing clear visual b.The parking space shall be outlined or painted blue and shall be marked with an International Symbol of O O DO rr O Q measured to the top of the outlet box. §11 B-308.1.1 25. The clear width for walking surfaces in corridors serving an occupant load of 10 or more shall be 44 inches contrast. Exterior stairs shall have the upper approach and all treads marked by a stripe providing clear Accessibility(ISA)complying with Section 11 B-703.7.2.1 ISA a minimum 36 inches wide by 36 inches high in Ir CE u�1 20. Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles minimum.§11B-403.5.1 exception 2 visual contrast.The stripe shall be a minimum of 2 inches wide to a maximum of 4 inches wide placed white or a suitable contrasting color.The centerline of the ISA shall be a maximum of 6 inches from the CL Q a- IRt LL 0 shall be located within allowable reach ranges. Low reach shall be measured to the bottom of the outlet box 26. The clear width for sidewalks and walks shall be 48 inches minimum.§11 B-403.5.1 exception 3 parallel to,and not more than 1 inch from,the nose of the step or upper approach.The stripe shall extend the centerline of the parking space, its sides parallel to the length of the parking space and its lower corner at, or and high reach shall be measured to the top of the outlet box.§11 B-308.1.2 27. The clear width for aisles shall be 36 inches minimum if serving elements on only one side, and 44 inches full width of the step or upper approach and shall be of material that is at least as slip resistant as the other lower side aligned with,the end of the parking space. §11 B-502.4.2 STORE #: 10183 � 21. High forward reach that is unobstructed shall be 48 inches maximum and the low forward reach shall be 15 minimum if serving elements on both sides. §11 B-403.5.1 exception 4 treads of the stair.A painted stripe shall be acceptable. Grooves shall not be used to satisfy this requirement. 23. An additional sign shall be posted either; 1) in a conspicuous place at each entrance to an off-street parking M inches minimum above the finish floor or round. 11 B-308.2.1, Figure 11 B-308.2.1 28. The clear width for accessible routes to accessible toilet compartments shall be 44 inches except for door 15 g § g § p p §i1 B-504.4.1 facility or 2) immediately adjacent to on-site accessible parking and visible from each parking space. PROJECT #: 27237-038 22. High forward reach shall be 48 inches maximum where the reach depth is 20 inches or less and 44 inches opening widths and door swings.§11 B-403.5.1 exception 5 76. The radius of curvature at the leading edge of the tread shall be 1/2 inch maximum.Nosings that project §11 B-502.8 maximum where the reach depth exceeds 20 inches. High forward reach shall not exceed 25 inches in beyond risers shall have the underside of the leading edge curved or beveled. Risers shall be permitted to a.The additional sign shall not be less than 17 inches wide by 22 inches high.§11 B-502.8.1 CASEWORK CONCEPT: op depth. §11B-308.2.2, Figure§1113-308.2.2 DOORS.DOORWAYS.AND GATES slope under the tread at an angle of 30 degrees maximum from vertical.The permitted projection of the b.The additional sign shall clearly state in letters with a.minimum height of 1 inch the following:§11 B-502.8.2 ISSUE DATE: 23. High side reach shall be 48 inches maximum and the low side reach shall be 15 inches minimum above the nosing shall extend 1-1/4 inches maximum over the tread below. §11B-504.5(Sea exception for existing "Unauthorized vehicles parked in designated accessible spaces not displaying distinguishing placards or DESIGN MANAGER: M. MONTENEGRO afinish floor where the side reach is unobstructed or the depth of any obstruction does not exceed 10 inches. 29. Doors,doorways, and gates providing user passage shall be provided in accordance with 11B-206.5 Doors, buildings) special license plates issued for persons with disabilities will be towed away at the owner's expense.Towed LEES AP: 07 §71 B-308.3.1, Figure§11 B-308.3.1 Doorways,and Gates. §11B-206.5 77. Stairs shall have handrails complying with Section 11 B-505 Handrails.§11 B-504.6 vehicles may be reclaimed at UNITED TOWING or by telephoning 800-526-6946." �N 24. High side reach shall be 46 inches maximum above the finish floor or ground where the high side reach is 30. Doors,doorways, and gates that are part of an accessible route shall comply with 11 B-404 Doors, Doorways, 78. Stair treads and landings subject to wet conditions shall be designed to prevent the accumulation of water. 24. Signs intended for use by pedestrians within parking facilities, including directional or informational signs PROGRAM MANAGER: W over an obstruction more than 10 inches but not more than 24 inches in depth.§11 B-308.3.2,Figure and Gates.§7113.404.1 §71 B-504.7 indicating parking sections or levels,shall comply with the requirements of Section 11 B-216. §11 B-216.5.2 CHECKED BY: VALERIO d §1116-308.3.2 31. Revolving doors,revolving gates, and turnstiles shall not be part of an accessible route. §11 B-402.2.1 79. Floor identification signs required by Chapter 10,Section 1022.9 complying with Sections 11 13-703.1 Signs 0 25. Obstructions for high side reach shall not exceed 34 inches in height and 24 inches in depth. 32. At least one of the active leaves of doorways with two leaves shall comply with 11 B-404.2.3 Clear Width and General, 11 B-703.2 Raised Characters, 11 B-703.3 Braille and 11 B-703.5 Visual Characters shall be located RELATIONSHIP TO ACCESSIBLE ROUTES Revision Schedule a- §71B-308.3.2, Figure§11B-308.3.2 11 B-404.2.4 Maneuvering Clearances. §11 B-404.2.2 at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in 00 26. Obstructed high side reach for the top of washing machines and clothes dryers shall be permitted to be 36 33. Door openings shall provide a clear width of 32 inches minimum.Clear openings of doorways with swinging buildings two or more stories in height to identify the floor level.At the exit discharge level,the sign shall 25. Parking spaces and access aisles shall be designed se that persons using them are not required to travel Rev Date By Description inches maximum above the finish floor. §11 B-308.3.2 doors shall be measured between the face of the door and the stop,with the door open 90 degrees. Openings include a raised five pointed star located to the left of the identifying floor level. The outside diameter of the behind parking spaces other than to pass behind the parking space in which they parked. §71 B-502.7.1 Y p b 05-23-18 SS 90 PERCENT CD SET civ 27. Obstructed high side reach for the operable parts of fuel dispensers shall be permitted to be 54 inches more than 24 inches deep shall provide a clear opening of 36 inches minimum.There shall be no projections star shall be the same as the height of the raised characters. §116.504.8 26. A curb or wheel stop shall be provided if required[o prevent encroachment of vehicles over the required clear maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing into the required clear opening width lower than 34 inches above the finish floor or ground. Projections into the width of adjacent accessible routes. §71 B-502.7.2 06-06-18 SS 1 ST SUBMITTAL SET curbs.§11 B-308.3.2 clear opening width between 34 inches and 80 inches above the finish floor or ground shall not exceed 4 CURB RAMPS, BLENDED TRANSITIONS AND ISLANDS 1 inches.§11B-404.2.3 2 OPERABLE PARTS 34. Minimum maneuvering clearances at doors and gates shall comply with 11 B-404.2.4 Maneuvering 80. Perpendicular ramp runs shall have a running slope not steeper than 1:12(8.33%).§118.406.2.1 3 Clearances. Maneuvering clearances shall extend the full width of the doorway and the required latch side or 81. For perpendicular ramps,where provided,curb ramp flares shall not be steeper than 1:10. §118.406.2, 28. Operable parts shall be operable with one hand and shall not require tight grasping, pinching, or twisting of hinge side clearance.§11 B-404.2.4 Figure 11 B-406.2. SHEET TITLE: 2 the wrist. Force required to activate operable parts shall be 5 pounds maximum.§11B-309.4 35. Swinging doors and gates shall have maneuvering clearances complying with Table 11 B-404.2.4.1. 82. The running slope of the curb ramp segments shall be in-line with the direction of sidewalk travel. Ramp runs ADA NOTES d §11 B-404.2.4.1 shall have a running slope not steeper than 1:12(8.33%) §71 B-406.3.1, Figure 11B-406.3.2 36. Doorways less than 36 inches wide without doors or gates,sliding doors,or folding doors shall have 83. A turning space 48 inches minimum by 48 inches minimum shall be provided at the bottom of the curb ramp. It maneuvering clearances complying with Table 11 B-404.2.4.2.§11 B-404.2.4.2 The slope of the turning space in all directions shall be 1:48 maximum (2.083%)§11 B-406.3.2 N 37. Maneuvering clearances for forward approach shall be provided when any obstruction within 18 inches of the 84. Blended transition ramps shall have a running slope not steeper than 1:20(5/) §11 B-406.4.1 SCALE:AS SHOWN latch side an interior doorway, or within 24 inches of the latch side of an exterior doorway, projects more than 8 85. Curb ramps and the flared sides of curb ramps shall be located so that they do not project into vehicular Lii inches beyond the face of the door, measured perpendicular to the face of the door or gate. §118-004.2.4.3 traffic lanes,parking spaces, or parking access aisles.Curb ramps at marked crossings shall be wholly SHEET NUMBER: co contained within the markings, excluding any flared sides. §118.406.5.1 G-0030