|
CODE REQUIREMENTS (CBC)ACCESSIBLE ROUTES11B-206.2.1 SITE ARRIVAL POINTS.AT LEAST ONE ACCESSIBLE ROUTE SHALL BEPROVIDED WITHIN THE SITE FROM ACCESSIBLE PARKING SPACES ANDACCESSIBLE PASSENGER LOADING ZONES; PUBLIC STREETS AND SIDEWALKS;AND PUBLIC TRANSPORTATION STOPS TO THE ACCESSIBLE BUILDING OR FACILITYENTRANCE THEY SERVE.WHERE MORE THAN ONE ROUTE IS PROVIDED, ALLROUTES MUST BE ACCESSIBLE.11B-206.2.2 WITHIN A SITE.AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECTACCESSIBLE BUILDINGS, ACCESSIBLE FACILITIES, ACCESSIBLE ELEMENTS, ANDACCESSIBLE SPACES THAT ARE ON THE SAME SITE.11B-206.2.4 SPACES AND ELEMENTS.AT LEAST ONE ACCESSIBLE ROUTE SHALLCONNECT ACCESSIBLE BUILDING OR FACILITY ENTRANCES WITH ALL ACCESSIBLESPACES AND ELEMENTS WITHIN THE BUILDING OR FACILITY, INCLUDINGMEZZANINES,WHICH ARE OTHERWISE CONNECTED BY A CIRCULATION PATHUNLESS EXEMPTED BYSECTION 11B-206.2.3 EXCEPTIONS 1 THROUGH 7.11B-206.2.5RESTAURANTS, CAFETERIAS,BANQUET FACILITIES AND BARS.INRESTAURANTS, CAFETERIAS,BANQUET FACILITIES, BARS, AND SIMILARFACILITIES,AN ACCESSIBLE ROUTE SHALL BE PROVIDED TO ALLFUNCTIONALAREAS, INCLUDING RAISED OR SUNKEN AREAS, AND OUTDOOR AREAS.11B-206.2.8 EMPLOYEE WORK AREAS.COMMON USE CIRCULATION PATHS WITHINEMPLOYEE WORK AREAS SHALL COMPLY WITHSECTION 11B-402.11B-402.2 COMPONENTS.ACCESSIBLE ROUTES SHALL CONSIST OF ONE OR MOREOF THE FOLLOWING COMPONENTS: WALKING SURFACES WITH A RUNNING SLOPENOT STEEPER THAN 1:20, DOORWAYS, RAMPS, CURB RAMPS EXCLUDING THEFLARED SIDES, ELEVATORS, AND PLATFORM LIFTS. ALL COMPONENTS OF ANACCESSIBLE ROUTE SHALL COMPLY WITH THE APPLICABLE REQUIREMENTS OFDIVISION4.ACCESSIBILITY NOTES ACCESSIBILITY NOTES11B-406.2PERPENDICULAR CURB RAMPS.PERPENDICULAR CURB RAMPS SHALLCOMPLY WITH SECTIONS 11B-406.2 AND 11B-406.5.11B-406.2.1SLOPE.RAMP RUNS SHALL HAVE A RUNNING SLOPE NOT STEEPERTHAN 1:12.11B-406.2.2SIDES OF CURB RAMPS.WHERE PROVIDED, CURB RAMP FLARESSHALL NOT BE STEEPER THAN 1:10.11B-406.3PARALLEL CURB RAMPS.PARALLEL CURB RAMPS SHALL COMPLY WITHSECTIONS 11B-406.3 AND 11B-406.5.11B-406.3.1SLOPE.THE RUNNING SLOPE OF THE CURB RAMP SEGMENTS SHALLBE IN-LINE WITH THE DIRECTION OF SIDEWALK TRAVEL. RAMP RUNS SHALL HAVEARUNNING SLOPE NOT STEEPER THAN 1:12.11B-406.3.2TURNING SPACE.A TURNING SPACE 48 INCHES (1219 MM) MINIMUM BY48 INCHES (1219 MM) MINIMUM SHALL BE PROVIDED AT THE BOTTOM OF THE CURBRAMP. THE SLOPE OF THE TURNING SPACE IN ALL DIRECTIONS SHALL BE 1:48MAXIMUM.11B-406.5COMMON REQUIREMENTS.CURB RAMPS AND BLENDED TRANSITIONSSHALL COMPLY WITH SECTION 11B-406.5.CURB RAMPSDOORS AND DOORWAYS11B-404.2 MANUAL DOORS, DOORWAYS, AND MANUAL GATES.MANUAL DOORSAND DOORWAYS AND MANUAL GATES INTENDED FOR USER PASSAGE SHALLCOMPLY WITHSECTION 11B-404.2.11B-404.2.2 DOUBLE-LEAF DOORS AND GATES.AT LEAST ONE OF THE ACTIVELEAVES OF DOORWAYS WITH TWO LEAVES SHALL COMPLY WITHSECTIONS 11B-404.2.3 AND11B-404.2.4.11B-404.2.3 CLEAR WIDTH.DOOR OPENINGS SHALL PROVIDE A CLEAR WIDTH OF32 INCHES (813MM) MINIMUM. CLEAR OPENINGS OF DOORWAYS WITH SWINGINGDOORS SHALL BE MEASURED BETWEEN THE FACE OF THE DOOR AND THESTOP, WITH THE DOOR OPEN 90 DEGREES. OPENINGS MORE THAN 24 INCHES(610 MM) DEEP SHALL PROVIDE A CLEAR OPENING OF 36 INCHES (914MM)MINIMUM. THERE SHALL BE NO PROJECTIONS INTO THE REQUIRED CLEAROPENING WIDTH LOWER THAN 34 INCHES (864MM) ABOVE THE FINISH FLOOROR GROUND. PROJECTIONS INTO THE CLEAR OPENING WIDTH BETWEEN 34INCHES (864MM) AND 80 INCHES (2032MM) ABOVE THE FINISH FLOOR ORGROUND SHALL NOT EXCEED 4 INCHES (102MM).11B-404.2.4 MANEUVERING CLEARANCES.MINIMUM MANEUVERING CLEARANCESAT DOORS AND GATES SHALL COMPLY WITHSECTION 11B-404.2.4. MANEUVERINGCLEARANCES SHALL EXTEND THE FULL WIDTH OF THE DOORWAY AND THEREQUIRED LATCH SIDE OR HINGE SIDE CLEARANCE.11B-404.2.4.1 SWINGING DOORS AND GATES.SWINGING DOORS AND GATESSHALL HAVE MANEUVERING CLEARANCES COMPLYING WITH TABLE11B-404.2.4.1.11B-404.2.7 DOOR AND GATE HARDWARE.HANDLES, PULLS, LATCHES, LOCKS,AND OTHER OPERABLE PARTS ON DOORS AND GATES SHALL COMPLY WITHSECTION 11B-309.4. OPERABLE PARTS OF SUCH HARDWARE SHALL BE 34 INCHES(864MM) MINIMUM AND44 INCHES (1118 MM)MAXIMUM ABOVE THE FINISH FLOOROR GROUND. WHERE SLIDING DOORS ARE IN THE FULLY OPEN POSITION,OPERATING HARDWARE SHALL BE EXPOSED AND USABLE FROM BOTH SIDES.11B-404.2.10 DOOR AND GATE SURFACES.SWINGING DOOR AND GATE SURFACESWITHIN 10 INCHES (254MM) OF THE FINISH FLOOR OR GROUND MEASUREDVERTICALLY SHALL HAVE A SMOOTH SURFACE ON THE PUSH SIDE EXTENDINGTHE FULL WIDTH OF THE DOOR OR GATE. PARTS CREATING HORIZONTAL ORVERTICAL JOINTS IN THESE SURFACES SHALL BE WITHIN 1/16 INCH (1.6 MM) OFTHE SAME PLANE AS THE OTHERAND BE FREE OF SHARP OR ABRASIVE EDGES.CAVITIES CREATED BY ADDED KICK PLATES SHALL BE CAPPED.RAMPS11B-405.2 SLOPE.RAMP RUNS SHALL HAVE A RUNNING SLOPE NOT STEEPERTHAN 1:12.11B-405.4 FLOOR OR GROUND SURFACES.FLOOR OR GROUND SURFACES OFRAMP RUNS SHALL COMPLY WITHSECTION 11B-302. CHANGES IN LEVEL OTHERTHAN THE RUNNING SLOPE AND CROSS SLOPE ARE NOT PERMITTED ON RAMPRUNS.11B-405.5 CLEAR WIDTH.THE CLEAR WIDTH OF A RAMP RUNSHALL BE 48 INCHES(1219 MM)MINIMUM.11B-405.6 RISE.THE RISE FOR ANY RAMP RUN SHALL BE 30 INCHES (762MM)MAXIMUM.11B-405.7 LANDINGS.RAMPS SHALL HAVE LANDINGS AT THE TOP AND THEBOTTOM OF EACH RAMP RUN. LANDINGS SHALL COMPLY WITHSECTION 11B-405.7.(CONT.)FLOOR OR GROUND SPACES11B-302 FLOOR OR GROUND SURFACES11B-302.1 GENERAL.FLOOR AND GROUND SURFACES SHALL BE STABLE, FIRM, ANDSLIP RESISTANT AND SHALL COMPLY WITHSECTION 11B-302.11B-303 CHANGES IN LEVEL11B-303.1 GENERAL.WHERE CHANGES IN LEVEL ARE PERMITTED IN FLOOR ORGROUND SURFACES, THEY SHALL COMPLY WITHSECTION 11B-303.11B-303.2 VERTICAL.CHANGES IN LEVEL OF ¼ INCH (6.4 MM) HIGH MAXIMUM SHALLBE PERMITTED TO BE VERTICALAND WITHOUT EDGE TREATMENT.11B-303.3 BEVELED.CHANGES IN LEVEL BETWEEN ¼ INCH (6.4 MM) HIGH MINIMUMAND ½ INCH (12.7MM) HIGH MAXIMUM SHALL BE BEVELED WITH A SLOPE NOTSTEEPER THAN 1:2.11B-304 TURNING SPACE11B-304.3 SIZE.TURNING SPACE SHALL COMPLY WITHSECTION 11B-304.3.1 OR11B-304.3.2.11B-304.3.1 CIRCULAR SPACE.THE TURNING SPACE SHALL BE A SPACE OF 60INCHES (1524MM) DIAMETER MINIMUM. THE SPACE SHALL BE PERMITTED TOINCLUDE KNEE AND TOE CLEARANCE COMPLYING WITHSECTION 11B-306.11B-304.3.2 T-SHAPED SPACE.THE TURNING SPACE SHALL BE A T-SHAPED SPACEWITHIN A 60 INCH (1524MM) SQUARE MINIMUM WITH ARMS AND BASE 36 INCHES(914MM) WIDE MINIMUM. EACH ARM OF THE T SHALL BE CLEAR OF OBSTRUCTIONS12 INCHES (305 MM) MINIMUM IN EACH DIRECTION AND THE BASE SHALL BE CLEAROF OBSTRUCTIONS 24 INCHES (610 MM) MINIMUM. THE SPACE SHALL BE PERMITTEDTO INCLUDE KNEE AND TOE CLEARANCE COMPLYING WITHSECTION 11B-306 ONLYAT THE END OF EITHER THE BASE OR ONE ARM.11B-305.7 MANEUVERING CLEARANCE.WHERE A CLEAR FLOOR OR GROUNDSPACE IS LOCATED IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OFTHREE SIDES, ADDITIONAL MANEUVERING CLEARANCE SHALL BE PROVIDED INACCORDANCE WITHSECTIONS 11B-305.7.1 AND11B-305.7.2.11B-305.7.1 FORWARD APPROACH.ALCOVES SHALL BE 36 INCHES (914MM) WIDEMINIMUM WHERE THE DEPTH EXCEEDS 24 INCHES (610 MM).11B-305.7.2 PARALLEL APPROACH.ALCOVES SHALL BE 60 INCHES (1524MM) WIDEMINIMUM WHERE THE DEPTH EXCEEDS 15 INCHES (381MM).11B-305CLEARFLOORORGROUNDSPACE11B-305.2 FLOOR OR GROUND SURFACES.FLOORORGROUNDSURFACESOFACLEAR FLOOR OR GROUND SPACE SHALL COMPLY WITHSECTION 11B-302.CHANGES IN LEVEL ARE NOT PERMITTED.EXCEPTION:SLOPES NOT STEEPER THAN 1:48 SHALL BE PERMITTED.11B-305.3 SIZE.THE CLEAR FLOOR OR GROUND SPACE SHALL BE 30 INCHES (762MM) MINIMUM BY 48 INCHES (1219MM) MINIMUM.11B-305.4 KNEE AND TOE CLEARANCE.UNLESS OTHERWISE SPECIFIED, CLEARFLOOR OR GROUND SPACE SHALL BE PERMITTED TO INCLUDE KNEE AND TOECLEARANCE COMPLYING WITHSECTION 11B-306.11B-305.5 POSITION.UNLESS OTHERWISE SPECIFIED, CLEAR FLOOR OR GROUNDSPACE SHALL BE POSITIONED FOR EITHER FORWARD OR PARALLEL APPROACH TOANELEMENT.11B-305.6 APPROACH.ONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR ORGROUND SPACE SHALL ADJOIN AN ACCESSIBLE ROUTE OR ADJOIN ANOTHERCLEAR FLOOR OR GROUND SPACE.11B-305.7 MANEUVERING CLEARANCE.WHERE A CLEAR FLOOR OR GROUNDSPACE IS LOCATED IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OFTHREE SIDES, ADDITIONAL MANEUVERING CLEARANCE SHALL BE PROVIDED INACCORDANCE WITHSECTIONS 11B-305.7.1 AND11B-305.7.2.11B-305.7.1 FORWARD APPROACH.ALCOVES SHALL BE 36 INCHES (914MM) WIDEMINIMUM WHERE THE DEPTH EXCEEDS 24 INCHES (610 MM).11B-305.7.2 PARALLEL APPROACH.ALCOVES SHALL BE 60 INCHES (1524MM) WIDEMINIMUM WHERE THE DEPTH EXCEEDS 15 INCHES (381MM).11B-306 KNEE AND TOE CLEARANCE11B-306.1 GENERAL.WHERE SPACE BENEATH AN ELEMENT IS INCLUDED AS PARTOF CLEAR FLOOR OR GROUND SPACE OR TURNING SPACE, THE SPACE SHALLCOMPLY WITHSECTION 11B-306. ADDITIONAL SPACE SHALL NOT BE PROHIBITEDBENEATH AN ELEMENT BUT SHALL NOT BE CONSIDERED AS PART OF THE CLEARFLOOR OR GROUND SPACE OR TURNING SPACE.11B-306.2 TOE CLEARANCE.11B-306.2.1 GENERAL.SPACE UNDER AN ELEMENT BETWEEN THE FINISH FLOOR ORGROUND AND 9 INCHES (229MM) ABOVE THE FINISH FLOOR OR GROUND SHALL BECONSIDERED TOE CLEARANCE AND SHALL COMPLY WITHSECTION 11B-306.2.FLOOR OR GROUND SPACES (CONT.)11B-306.2.2 MAXIMUM DEPTH.TOE CLEARANCE SHALL EXTEND 25 INCHES (635 MM)MAXIMUM UNDER AN ELEMENT.11B-306.2.3 MINIMUM REQUIRED DEPTH.WHERE TOE CLEARANCE IS REQUIRED ATAN ELEMENT AS PART OF A CLEAR FLOOR SPACE, THE TOE CLEARANCE SHALLEXTEND 17 INCHES (432MM) MINIMUM UNDER THE ELEMENT.11B-306.2.4 ADDITIONAL CLEARANCE.SPACE EXTENDING GREATER THAN 6INCHES (152MM) BEYOND THE AVAILABLE KNEE CLEARANCE AT 9 INCHES (229MM)ABOVE THE FINISH FLOOR OR GROUND SHALL NOT BE CONSIDERED TOECLEARANCE.11B-306.2.5 WIDTH.TOE CLEARANCE SHALL BE 30 INCHES (762MM) WIDE MINIMUM.11B-306.3 KNEE CLEARANCE.11B-306.3.1 GENERAL.SPACE UNDER AN ELEMENT BETWEEN 9 INCHES (229MM)AND 27 INCHES (686MM) ABOVE THE FINISH FLOOR OR GROUND SHALL BECONSIDERED KNEE CLEARANCE AND SHALL COMPLY WITHSECTION 11B-306.3.11B-306.3.2 MAXIMUM DEPTH.KNEE CLEARANCE SHALL EXTEND 25 INCHES (635MM) MAXIMUM UNDER AN ELEMENT AT 9 INCHES (229MM) ABOVE THE FINISHFLOOR OR GROUND.11B-306.3.3 MINIMUM REQUIRED DEPTH.WHERE KNEE CLEARANCE IS REQUIREDUNDER AN ELEMENT AS PART OF A CLEAR FLOOR SPACE, THE KNEE CLEARANCESHALL BE 11 INCHES (279MM) DEEP MINIMUM AT 9 INCHES (229MM) ABOVE THEFINISH FLOOR OR GROUND, AND 8 INCHES (203MM) DEEP MINIMUM AT 27 INCHES(686MM) ABOVE THE FINISH FLOOR OR GROUND.11B-306.3.4 CLEARANCE REDUCTION.BETWEEN 9 INCHES (229MM) AND 27 INCHES(686MM) ABOVE THE FINISH FLOOR OR GROUND, THE KNEE CLEARANCE SHALL BEPERMITTED TO REDUCE AT A RATE OF 1 INCH (25 MM) IN DEPTH FOR EACH 6INCHES (152MM) IN HEIGHT.11B-306.3.5 WIDTH.KNEE CLEARANCE SHALL BE 30 INCHES (762MM) WIDEMINIMUM.REACH RANGES11B-308 REACH RANGES11B-308.1.1 ELECTRICAL SWITCHES.CONTROLS AND SWITCHES INTENDED TO BEUSED BY THE OCCUPANT OF A ROOM OR AREA TO CONTROL LIGHTING ANDRECEPTACLE OUTLETS, APPLIANCES OR COOLING, HEATING AND VENTILATINGEQUIPMENT, SHALL COMPLY WITH SECTION 11B-308 EXCEPT THE LOW REACHSHALL BE MEASURED TO THE BOTTOM OF THE OUTLET BOX AND THE HIGH REACHSHALL BE MEASURED TO THE TOP OF THE OUTLET BOX.11B-308.1.2 ELECTRICAL RECEPTACLE OUTLETS.ELECTRICAL RECEPTACLEOUTLETS ON BRANCH CIRCUITS OF 30 AMPERES OR LESS AND COMMUNICATIONSYSTEM RECEPTACLES SHALL COMPLY WITH SECTION 11B-308 EXCEPT THE LOWREACH SHALL BE MEASURED TO THE BOTTOM OF THE OUTLET BOX AND THE HIGHREACH SHALL BE MEASURED TO THE TOP OF THE OUTLET BOX.11B-308.2 FORWARD REACH.11B-308.2.1 UNOBSTRUCTED.WHERE A FORWARD REACH IS UNOBSTRUCTED, THEHIGH FORWARD REACH SHALL BE 48 INCHES (1219MM) MAXIMUM AND THE LOWFORWARD REACH SHALL BE 15 INCHES (381MM) MINIMUM ABOVE THE FINISHFLOOR OR GROUND.11B-308.2.2 OBSTRUCTED HIGH REACH.WHERE A HIGH FORWARD REACH IS OVERAN OBSTRUCTION, THE CLEAR FLOOR SPACE SHALL EXTEND BENEATH THEELEMENT FOR A DISTANCE NOT LESS THAN THE REQUIRED REACH DEPTH OVERTHE OBSTRUCTION. THE HIGH FORWARD REACH SHALL BE 48 INCHES (1219MM)MAXIMUM WHERE THE REACH DEPTH IS 20 INCHES (508MM) MAXIMUM. WHERETHE REACH DEPTH EXCEEDS 20 INCHES (508MM), THE HIGH FORWARD REACHSHALL BE 44 INCHES (1118MM) MAXIMUM AND THE REACH DEPTH SHALL BE 25INCHES (635 MM) MAXIMUM.11B-308.3 SIDE REACH.11B-308.3.1 UNOBSTRUCTED.WHERE A CLEAR FLOOR OR GROUND SPACEALLOWS A PARALLEL APPROACH TO AN ELEMENT AND THE SIDE REACH ISUNOBSTRUCTED, THE HIGH SIDE REACH SHALL BE 48 INCHES (1219MM) MAXIMUMAND THE LOW SIDE REACH SHALL BE 15 INCHES (381MM) MINIMUM ABOVE THEFINISHFLOORORGROUND.11B-308.3.2 OBSTRUCTED HIGH REACH.WHERE A CLEAR FLOOR OR GROUNDSPACE ALLOWS A PARALLEL APPROACH TO AN ELEMENT AND THE HIGH SIDEREACH IS OVER AN OBSTRUCTION, THE HEIGHT OF THE OBSTRUCTION SHALL BE34 INCHES (864MM) MAXIMUM AND THE DEPTH OF THE OBSTRUCTION SHALL BE 24INCHES (610 MM) MAXIMUM. THE HIGH SIDE REACH SHALL BE 48 INCHES (1219MM)MAXIMUM FOR A REACH DEPTH OF 10 INCHES (254MM) MAXIMUM. WHERE THEREACH DEPTH EXCEEDS 10 INCHES (254MM), THE HIGH SIDE REACH SHALL BE 46INCHES (1168MM) MAXIMUM FOR A REACH DEPTH OF 24 INCHES (610 MM)MAXIMUM.11B-309 OPERABLE PARTS11B-309.1 GENERAL.OPERABLE PARTS SHALL COMPLY WITHSECTION 11B-309.11B-309.2 CLEAR FLOOR SPACE.A CLEAR FLOOR OR GROUND SPACE COMPLYINGWITHSECTION 11B-305 SHALL BE PROVIDED.11B-309.3 HEIGHT.OPERABLE PARTS SHALL BE PLACED WITHIN ONE OR MORE OFTHE REACH RANGES SPECIFIED INSECTION 11B-308.11B-309.4 OPERATION.OPERABLE PARTS SHALL BE OPERABLE WITH ONE HANDAND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THEWRIST. THE FORCE REQUIRED TO ACTIVATE OPERABLE PARTS SHALL BE 5POUNDS (22.2 N) MAXIMUM.DOORS AND DOORWAYS (CONT.)MEN WOMENLETTERING RAISED 1/32"NOTE:WALL MOUNTED SIGNAGE TO BE LOCATED ONLATCH SIDE OF DOOR CLEAR OF DOOR-SWING.MOUNT AT 60" TO CENTERLINE OF SIGN FROMFLOOR.CORRESPONDING GRADE II BRAILLE. PERCBC SECT. 11B-703.3.2 BRAILLE SHALL BEFLUSH LEFT OR CENTERED AND PLACED AMIN. OF 3/8" INCH AND MAXIMUM OF 1/2INCH BELOW RAISED CHARACTERS ORSYMBOLSHEIGHT OF LETTERING 5/8"MIN. TO 2" MAX.1' - 0"1' - 0"WOMENFINISH FLOOR48" MIN.60" MAX.SYMBOLS SHALL BE MOUNTED ON THE DOOR AT A HEIGHT OF +60" AFF TO THECENTERLINE OF SIGN, & THEIR COLOR AND CONTRAST SHALL BE DISTINCTLYDIFFERENT FROM THE COLOR & CONTRAST OF THE DOOR.12" DIA3-IDENTIFICATION SYMBOLS:ON DOORWAYS LEADING TO MEN'S SANITARY FACILITIES AN EQUILATERALTRIANGLE 1/4" THICK WITH EDGES 12" LONG AND A VERTEX POINTINGUPWARD.SANITARY FACILITIESSECTION 2-1711. (TITLE 24 STATE BUILDING CODE)1' - 0"2.35"2.35"0.90"0.45".20"HT.ATTOPAT BASETYPICAL PLANGROUT BED.TYPICAL SECTION AA-NOTE:1. DETECTABLE WARNING SHALL BE OF CONTRASTING COLOR WITHADJACENTSURFACE: LIGHT-ON-DARK OR DARK-ON-LIGHT. MATERIAL SHALL BEINTEGRAL PART OF THE WALKING SURFACE.2. TRUNCATED DOMES TO BE: "INTERLOCK SAN DIEGO" TACTILE STONE,CARLSBAD, CALIFORNIA (760) 434-5566 OR APPROVED EQUAL.RECESS CONC. PER MFR.RECOMMENDATIONS.JOINT COLOR TO MATCH TILES.2401 UTAH AVENUE SOUTHSEATTLE, WASHINGTON 98134(206) 318-1575SHEET NUMBER:SHEET TITLE:SCALE: AS SHOWNSTORE #:PROFILE TYPE:PROJECT #:ISSUE DATE:PROGRAM MANAGER:STORE DESIGNER:CHECKED BY:PROJECT NAME:PROJECT ADDRESS:STARBUCKS COFFEECOMPANYRLEED AP:© 2017 STARBUCKS COFFEE COMPANY®111 Pacifica, Suite 280, Irvine, CA 92618P: 949.553.1117 F: 949.474.7056San FranciscoClevelandDenverIrvineARCHITECT OF RECORDARCHITECT STAMP2017MCG PROJ. MANAGER:MCG PROJ. SPECIALIST:MCG PROJECT #:THESE DRAWINGS AND SPECIFICATIONS ARECONFIDENTIAL AND SHALL REMAIN THE SOLEPROPERTY OF STARBUCKS CORPORATION,WHICH IS THE OWNER OF THE COPYRIGHT INTHIS WORK. THEY SHALL NOT BEREPRODUCED (IN WHOLE OR IN PART), SHAREDWITH THIRD PARTIES OR USED IN ANY MANNERON OTHER PROJECTS OR EXTENSIONS TO THISPROJECT WITHOUT THE PRIOR WRITTENCONSENT OF STARBUCKS CORPORATION.THESE DRAWINGS AND SPECIFICATIONS AREINTENDED TO EXPRESS DESIGN INTENT FOR APROTOTYPICAL STARBUCKS STORE (WHICH ISSUBJECT TO CHANGE AT ANYTIME) AND DONOT REFLECT ACTUAL SITE CONDITIONS.NEITHER PARTY SHALL HAVE ANY OBLIGATIONNOR LIABILITY TO THE OTHER (EXCEPT STATEDABOVE) UNTIL A WRITTEN AGREEMENT ISFULLY EXECUTED BY BOTH PARTIES.mcg architecture8/30/2017 5:42:47 PMJ:\2016 Projects\0-Starbucks\16514_SBX-6970_El Dorado & Fremont_Stockton_CA (NS-RELO)\02-Arch\3-CD\1-Revit Files\16514_SBX-6970_El Dorado & Fremont_Stockton.rvtG-000321295-04208/18/17ELDORADO &FREMONT510NELDORADOSTREETSTOCKTON, CA 95202SANJOAQUIN COUNTYCORE6970CH. LINM. DARMOKOACCESSIBILITY NOTESC. LEEG. MONTALVO16514Scale:11/2"=1'-0"14ACCESSIBLE ID WALL SYMBOLSScale:11/2"=1'-0"13ACCESSIBLE ID DOOR SYMBOLSScale:6" = 1'-0"1TRUNCATED DOMES3'-2" BOTTOM OFTOWEL DISPENSER2'-10" MAXTO RIM1'-2"EXISTING PAPERTOWELDISPENSER8"CLR1'-0"1'-0" MINx;1'-7"7"-9" MAXTOILET PAPER DISPENSERSEAT COVER DISPENSER48" GRAB BAR2'-9"12" 12" 12"WOMENMEN UNISEXSYMBOL DESCRIPTIONSALL SIGNAGE: SIGNS ARE TO BE CENTERED ON THE DOOR 60" FROM THEFLOOR. THE COLOR AND CONTRAST OF THE SIGN DISTINCTIVELYCONTRASTS WITH THE COLOR AND CONTRAST OF THE DOOR.MEN'S SIGNAGE: EQUILATERAL TRIANGLE, 1/4" THICK WITH EDGES 12"LONG & A VERTEX POINTING UPWARD.UNISEX SIGNAGE: 12" DIAMETER CIRCLE, 1/4" THICK TRIANGLESUPERIMPOSED WITHIN CIRCLE.WOMEN'S SIGNAGE: 12" DIAMETER CIRCLE, 1/4" THICK.CLHARDWARE HEIGHT34"-44"CBC SECT 1008.1.1 - DOOR SIZE* 3'-0" DOOR WIDTH* 6'-8" HEIGHT* 32" CLEAR WIDTHCBC SECT 11B-404.2.9 - DOOR OPENING FORCE* TYPE OF HARDWARE: PUSH/PULL* MAX. EFFORT OFR EXT. DOORS = 5 LBS* MAX. EFFORT FOR INT. DOORS = 5 LBS.* REQUIRED FIRE DOORS, MAX. EFFORT = 15 LBS.CBC SECT 1133B.2.6 - SMOOTH SURFACECBC SECT 11B-404.2.10 - THRESHOLDS*1/2" MAX. THRESHOLD*1/4" FT. MAX. SLOPE* 10" KICKPLATE OR SMOOTH FULLWIDTH OF DOOR* 4" FOR SOLD GLASS DOORSINTERIOREXTERIORScale: N.T.S.SECTION @ ENTRY DOORADA COMPIANCE DETAIL17Scale: N.T.S.RESTROOM DOOR SIGNAGE18Scale: 3/8" = 1'=0"TYPICAL RESTROOM ACCESSIBLEMOUNTING HEIGHTSELEVATION19Scale = 3/8" = 1'-0" ELEVATIONTYPICAL RESTROOMACCESSIBLE MOUNTING HEIGHTS203'-31/2" BOTTOMOF MIRROR6"2'-9"1'-5"1'-6"3'-6" MINTOILET PAPERDISPENSER36" GRAB BARScale = 3/8" = 1'-0" ELEVATIONTYPICAL RESTROOMACCESSIBLE MOUNTING HEIGHTS9"EQEQ60"G-000318UNISEXUNISEX SIGNAGESHOWN,DESIGNATED SIGNAGEFOR MEN'S & WOMEN'SRESTROOMS USEDWHENAPPLICABLE.NOTE:DOOR-MOUNTED RESTROOMSIGNAGE TO COMPLY WITHCALIFORNIA TITLE 24 A.D.A.REQUIREMENTS.GC TO VERIFY COMPLIANCEAND PROVIDE ADDITIONALSIGNAGE AS NECESSARY.Scale: 1/2" = 1'=0"RR DOOR SIGNAGEELEVATION1516Revision ScheduleRev Date By Description
|