|
ACCESSIBILITY NOTES (CONT.)LAVATORIES11B-606 LAVATORIES AND SINKS11B-606.2 CLEAR FLOOR SPACE.A CLEAR FLOOR SPACE COMPLYING WITHSECTION 11B-305, POSITIONED FOR A FORWARD APPROACH, AND KNEE ANDTOE CLEARANCE COMPLYING WITHSECTION 11B-306 SHALL BE PROVIDED.11B-606.3 HEIGHT.LAVATORIES AND SINKS SHALL BE INSTALLED WITH THEFRONT OF THE HIGHER OF THE RIM OR COUNTER SURFACE 34 INCHES (864MM) MAXIMUM ABOVE THE FINISH FLOOR OR GROUND.11B-606.4 FAUCETS.CONTROLS FOR FAUCETS SHALL COMPLY WITHSECTION11B-309. HAND-OPERATED METERING FAUCETS SHALL REMAIN OPEN FOR 10SECONDS MINIMUM.LAVATORIES CONT.11B-606.5 EXPOSED PIPES AND SURFACES.WATER SUPPLY AND DRAIN PIPESUNDER LAVATORIES AND SINKS SHALL BE INSULATED OR OTHERWISECONFIGURED TO PROTECT AGAINST CONTACT. THERE SHALL BE NO SHARP ORABRASIVE SURFACES UNDER LAVATORIES AND SINKS.11B-606.6 ADJACENT SIDE WALL OR PARTITION.LAVATORIES, WHEN LOCATEDADJACENT TO A SIDE WALL OR PARTITION, SHALL BE A MINIMUM OF 18 INCHES(457 MM) TO THE CENTERLINE OF THE FIXTURE.11B-606.7 SINK DEPTH.SINKS SHALL BE 6½ INCHES (165 MM) DEEP MAXIMUM.11B-406.5.1LOCATION.CURB RAMPS AND THE FLARED SIDES OF CURB RAMPSSHALL BE LOCATED SO THAT THEY DO NOT PROJECT INTO VEHICULAR TRAFFICLANES, PARKING SPACES, OR PARKING ACCESS AISLES. CURB RAMPS AT MARKEDCROSSINGS SHALL BE WHOLLY CONTAINED WITHIN THE MARKINGS, EXCLUDINGANY FLARED SIDES.11B-406.5.2WIDTH.THE CLEAR WIDTH OF CURB RAMP RUNS (EXCLUDING ANYFLARED SIDES), BLENDED TRANSITIONS, AND TURNING SPACES SHALL BE 48INCHES (1219 MM) MINIMUM.11B-406.5.3LANDINGS.LANDINGS SHALL BE PROVIDED AT THE TOPS OF CURBRAMPS AND BLENDED TRANSITIONS. THE LANDING CLEAR LENGTH SHALL BE 48INCHES (1219 MM) MINIMUM. THE LANDING CLEAR WIDTH SHALL BE AT LEAST ASWIDE AS THE CURB RAMP, EXCLUDING ANY FLARED SIDES, OR THE BLENDEDTRANSITION LEADING TO THE LANDING. THE SLOPE OF THE LANDING IN ALLDIRECTIONS SHALL BE 1:48 MAXIMUM.11B-406.5.11GROOVED BORDER.CURB RAMPS SHALL HAVE A GROOVED BORDER12 INCHES (305 MM) WIDE ALONG THE TOP OF THE CURB RAMP AT THE LEVELSURFACE OF THE TOP LANDING AND AT THE OUTSIDE EDGES OF THE FLAREDSIDES. THE GROOVED BORDER SHALL CONSIST OF A SERIES OF GROOVES ¼ INCH(6.4 MM) WIDE BY ¼ INCH (6.4 MM) DEEP, AT ¾ INCH (19 MM) ON CENTER.11B-406.5.12DETECTABLE WARNINGS.CURB RAMPS AND BLENDED TRANSITIONSSHALL HAVE DETECTABLE WARNINGS COMPLYING WITH SECTION 11B-705.CURB RAMPS (CONT.)PARKING SPACES11B-502 PARKING SPACES11B-502.1 GENERAL.CAR AND VAN PARKING SPACES SHALL COMPLY WITHSECTION 11B-502. WHERE PARKING SPACES ARE MARKED WITH LINES, WIDTHMEASUREMENTS OF PARKING SPACES AND ACCESS AISLES SHALL BE MADEFROM THE CENTERLINE OF THE MARKINGS.11B-502.2 VEHICLE SPACES.CAR AND VAN PARKING SPACES SHALL BE 216 INCHES(5486 MM) LONG MINIMUM.CAR PARKING SPACES SHALL BE108 INCHES (2743 MM)WIDE MINIMUM AND VAN PARKING SPACES SHALL BE144 INCHES (3658 MM)WIDEMINIMUM, SHALL BE MARKED TO DEFINE THE WIDTH, AND SHALL HAVE ANADJACENT ACCESS AISLE COMPLYING WITHSECTION 11B-502.3.11B-502.3 ACCESS AISLE.ACCESS AISLES SERVING PARKING SPACES SHALLCOMPLY WITHSECTION 11B-502.3. ACCESS AISLES SHALL ADJOIN AN ACCESSIBLEROUTE. TWO PARKING SPACES SHALL BE PERMITTED TO SHARE A COMMONACCESS AISLE.11B-502.3.2 LENGTH.ACCESS AISLES SHALL EXTEND THE FULLREQUIREDLENGTHOF THE PARKING SPACES THEY SERVE.11B-502.3.3 MARKING.ACCESS AISLES SHALL BE MARKED WITH A BLUE PAINTEDBORDERLINE AROUND THEIR PERIMETER. THE AREA WITHIN THE BLUEBORDERLINES SHALL BE MARKED WITH HATCHED LINES A MAXIMUM OF 36 INCHES(914 MM) ON CENTER IN A COLOR CONTRASTING WITH THAT OF THE AISLESURFACE, PREFERABLY BLUE OR WHITE. THE WORDS "NO PARKING" SHALL BEPAINTED ON THE SURFACE WITHIN EACH ACCESS AISLE IN WHITE LETTERS AMINIMUM OF 12 INCHES (305 MM) IN HEIGHT AND LOCATED TO BE VISIBLE FROMTHE ADJACENT VEHICULAR WAY. ACCESS AISLE MARKINGS MAY EXTEND BEYONDTHE MINIMUM REQUIRED LENGTH.11B-502.3.4 LOCATION.ACCESS AISLES SHALL NOT OVERLAP THE VEHICULARWAY. ACCESS AISLES SHALL BE PERMITTED TO BE PLACED ON EITHER SIDE OFTHE PARKING SPACE EXCEPT FOR VAN PARKING SPACES WHICH SHALL HAVEACCESS AISLES LOCATED ON THE PASSENGER SIDE OF THE PARKING SPACES.11B-502.4 FLOOR OR GROUND SURFACES.PARKING SPACES AND ACCESS AISLESSERVING THEM SHALL COMPLY WITHSECTION 11B-302. ACCESS AISLES SHALL BEAT THE SAME LEVEL AS THE PARKING SPACES THEY SERVE. CHANGES IN LEVELARE NOT PERMITTED.11B-502.5 VERTICAL CLEARANCE.PARKINGSPACES,ACCESS AISLES ANDVEHICULAR ROUTES SERVING THEM SHALL PROVIDE A VERTICAL CLEARANCE OF98 INCHES (2489MM) MINIMUM.11B-502.6 IDENTIFICATION.PARKING SPACE IDENTIFICATION SIGNS SHALL INCLUDETHE INTERNATIONAL SYMBOL OF ACCESSIBILITY COMPLYING WITHSECTION 11B-703.7.2.1. SIGNS IDENTIFYING VAN PARKING SPACES SHALL CONTAINADDITIONALLANGUAGE OR AN ADDITIONAL SIGN WITHTHE DESIGNATION “VAN ACCESSIBLE.”SIGNS SHALL BE 60 INCHES (1524MM) MINIMUM ABOVE THE FINISH FLOOR ORGROUND SURFACE MEASURED TO THE BOTTOM OF THE SIGN.11B-502.6.1FINISH AND SIZE.PARKING IDENTIFICATION SIGNS SHALL BEREFLECTORIZED WITH A MINIMUM AREA OF 70 SQUARE INCHES (45161 MM2).11B-502.6.2MINIMUM FINE.ADDITIONAL LANGUAGE OR AN ADDITIONAL SIGNBELOW THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL STATE “MINIMUMFINE $250.”11B-502.6.3LOCATION.A PARKING SPACE IDENTIFICATION SIGN SHALL BE VISIBLEFROM EACH PARKING SPACE. SIGNS SHALL BE PERMANENTLY POSTED EITHERIMMEDIATELY ADJACENT TO THE PARKING SPACE OR WITHIN THE PROJECTEDPARKING SPACE WIDTH AT THE HEAD END OF THE PARKING SPACE. SIGNS MAYALSO BE PERMANENTLY POSTED ON A WALL AT THE INTERIOR END OF THEPARKING SPACE.11B-502.6.4MARKING.EACH ACCESSIBLE CAR AND VAN SPACE SHALL HAVESURFACE IDENTIFICATION COMPLYING WITH EITHER SECTION 11B-502.6.4.1 OR11B-502.6.4.2.11B-502.6.4.1THE PARKING SPACE SHALL BE MARKED WITH AN INTERNATIONALSYMBOL OF ACCESSIBILITY COMPLYING WITH SECTION 11B-703.7.2.1 IN WHITE ONABLUE BACKGROUND A MINIMUM 36 INCHES WIDE BY 36 INCHES HIGH (914 MM X914 MM). THE CENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITYSHALL BE A MAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THEPARKING SPACE, ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACEAND ITS LOWER CORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THEPARKING SPACE LENGTH.11B-502.6.4.2THE PARKING SPACE SHALL BE OUTLINED OR PAINTED BLUE ANDSHALL BE MARKED WITH AN INTERNATIONAL SYMBOL OF ACCESSIBILITYCOMPLYING WITH SECTION 11B-703.7.2.1 A MINIMUM 36 INCHES WIDE BY 36 INCHESHIGH (914 MM X 914 MM) IN WHITE OR A SUITABLE CONTRASTING COLOR. THECENTERLINE OF THE INTERNATIONAL SYMBOL OF ACCESSIBILITY SHALL BE AMAXIMUM OF 6 INCHES (152 MM) FROM THE CENTERLINE OF THE PARKING SPACE,ITS SIDES PARALLEL TO THE LENGTH OF THE PARKING SPACE AND ITS LOWERCORNER AT, OR LOWER SIDE ALIGNED WITH, THE END OF THE PARKING SPACE.11B-502.8ADDITIONAL SIGNAGE.AN ADDITIONAL SIGN SHALL BE POSTED EITHER;1) IN A CONSPICUOUS PLACE AT EACH ENTRANCE TO AN OFF-STREET PARKINGFACILITY OR 2) IMMEDIATELY ADJACENT TO ON-SITE ACCESSIBLE PARKING ANDVISIBLE FROM EACH PARKING SPACE.11B-502.8.1SIZE.THE ADDITIONAL SIGN SHALL NOT BE LESS THAN 17 INCHES (432MM) WIDE BY 22 INCHES (559 MM) HIGH.11B-502.8.2LETTERING.THE ADDITIONAL SIGN SHALL CLEARLY STATE IN LETTERSWITH A MINIMUM HEIGHT OF 1 INCH (25 MM) THE FOLLOWING:PARKING CONT."UNAUTHORIZED VEHICLES PARKED IN DESIGNATED ACCESSIBLE SPACES NOTDISPLAYING DISTINGUISHING PLACARDS OR SPECIAL LICENSE PLATES ISSUEDFOR PERSONS WITH DISABILITIES WILL BE TOWED AWAY AT THE OWNER’SEXPENSE. TOWED VEHICLES MAY BE RECLAIMED AT:_________________________ OR BY TELEPHONING __________________."BLANK SPACES SHALL BE FILLED IN WITH APPROPRIATE INFORMATION AS APERMANENT PART OF THE SIGN.WATER CLOSETS11B-604 WATER CLOSETS11B-604.2 LOCATION.THE WATER CLOSET SHALL BE POSITIONED WITH A WALLOR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE WATERCLOSET SHALL BE17 INCHES (432 MM)MINIMUM TO 18 INCHES (457MM)MAXIMUM FROM THE SIDE WALL OR PARTITION, EXCEPT THAT THE WATERCLOSET SHALL BE 17 INCHES (432MM) MINIMUM AND 19 INCHES (483MM)MAXIMUM FROM THE SIDE WALL OR PARTITION IN THE AMBULATORY ACCESSIBLETOILET COMPARTMENT SPECIFIED INSECTION 11B-604.8.2. WATER CLOSETSSHALL BE ARRANGED FOR A LEFT-HAND OR RIGHT-HAND APPROACH.11B-604.3 CLEARANCE.CLEARANCES AROUND WATER CLOSETS AND IN TOILETCOMPARTMENTS SHALL COMPLY WITHSECTION 11B-604.3.11B-604.3.1 SIZE.CLEARANCE AROUND A WATER CLOSET SHALL BE 60 INCHES(1524MM) MINIMUM MEASURED PERPENDICULAR FROM THE SIDE WALL AND 56INCHES (1422MM) MINIMUM MEASURED PERPENDICULAR FROM THE REAR WALL.AMINIMUM 60 INCHES (1524 MM) WIDE AND 48 INCHES (1219 MM) DEEPMANEUVERING SPACE SHALL BE PROVIDED IN FRONT OF THE WATER CLOSET.11B-604.3.2 OVERLAP.THE REQUIRED CLEARANCE AROUND THE WATER CLOSETSHALL BE PERMITTED TO OVERLAP THE WATER CLOSET, ASSOCIATED GRABBARS, DISPENSERS, SANITARY NAPKIN DISPOSAL UNITS, COAT HOOKS, SHELVES,ACCESSIBLE ROUTES, CLEAR FLOOR SPACE AND CLEARANCES REQUIRED ATOTHER FIXTURES, AND THE TURNING SPACE. NO OTHER FIXTURES OROBSTRUCTIONS SHALL BE LOCATED WITHIN THE REQUIRED WATER CLOSETCLEARANCE.11B-604.4 SEATS.THE SEAT HEIGHT OF A WATER CLOSET ABOVE THE FINISHFLOOR SHALL BE 17 INCHES (432MM) MINIMUM AND 19 INCHES (483MM)MAXIMUM MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUNGTO RETURN TO A LIFTED POSITION.SEATS SHALL BE 2 INCHES (51 MM) HIGHMAXIMUM.11B-604.5 GRAB BARS.GRAB BARS FOR WATER CLOSETS SHALL COMPLY WITHSECTION 11B-609. GRAB BARS SHALL BE PROVIDED ON THE SIDE WALL CLOSESTTO THE WATER CLOSET AND ON THE REAR WALL.WHERE SEPARATE GRAB BARSARE REQUIRED ON ADJACENT WALLS AT A COMMON MOUNTING HEIGHT, AN L-SHAPED GRAB BAR MEETING THE DIMENSIONAL REQUIREMENTS OF SECTIONS11B-604.5.1 AND 11B-604.5.2 SHALL BE PERMITTED.11B-604.5.1 SIDE WALL.THE SIDE WALL GRAB BAR SHALL BE 42 INCHES (1067MM)LONG MINIMUM, LOCATED 12 INCHES (305 MM) MAXIMUM FROM THE REAR WALLAND EXTENDING 54 INCHES (1372MM) MINIMUM FROM THE REAR WALLWITH THEFRONT END POSITIONED 24 INCHES (610 MM) MINIMUM IN FRONT OF THE WATERCLOSET.11B-604.5.2 REAR WALL.THE REAR WALL GRAB BAR SHALL BE 36 INCHES (914MM) LONG MINIMUM AND EXTEND FROM THE CENTERLINE OF THE WATERCLOSET 12 INCHES (305 MM) MINIMUM ON ONE SIDE AND 24 INCHES (610 MM)MINIMUM ON THE OTHER SIDE.11B-604.6 FLUSH CONTROLS.FLUSH CONTROLS SHALL BE HAND OPERATED ORAUTOMATIC. HAND OPERATED FLUSH CONTROLS SHALL COMPLY WITHSECTION11B-309EXCEPT THEY SHALL BE LOCATED 44 INCHES (1118 MM) MAXIMUM ABOVETHE FLOOR. FLUSH CONTROLS SHALL BE LOCATED ON THE OPEN SIDE OF THEWATER CLOSET EXCEPT IN AMBULATORY ACCESSIBLE COMPARTMENTSCOMPLYING WITHSECTION 11B-604.8.2.11B-604.7 DISPENSERS.TOILET PAPER DISPENSERS SHALL COMPLY WITHSECTION 11B-309.4 AND SHALL BE 7 INCHES (178MM) MINIMUM AND 9 INCHES (229MM) MAXIMUM IN FRONT OF THE WATER CLOSET MEASURED TO THECENTERLINE OF THE DISPENSER. THE OUTLET OF THE DISPENSER SHALL BEBELOW THE GRAB BAR, 19 INCHES (483 MM) MINIMUMABOVE THE FINISH FLOORAND SHALL NOT BE LOCATED BEHIND GRAB BARS. DISPENSERS SHALL NOT BEOF A TYPE THAT CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUSPAPER FLOW.TOILET ROOMS11B-603 TOILET AND BATHING ROOMS11B-603.2 CLEARANCES.CLEARANCES SHALL COMPLY WITHSECTION 11B-603.2.11B-603.2.1 TURNING SPACE.TURNING SPACE COMPLYING WITHSECTION 11B-304 SHALL BE PROVIDED WITHIN THE ROOM.11B-603.2.2 OVERLAP.REQUIRED CLEAR FLOOR SPACES, CLEARANCE ATFIXTURES, AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP.11B-603.2.3 DOOR SWING.DOORS SHALL NOT SWING INTO THE CLEAR FLOORSPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. OTHER THAN THE DOORTO THE ACCESSIBLE WATER CLOSET COMPARTMENT, A DOOR, IN ANYPOSITION, MAY ENCROACH INTO THE TURNING SPACE BY 12 INCHES (305 MM)MAXIMUM.11B-603.3 MIRRORS.MIRRORS LOCATED ABOVE LAVATORIES ORCOUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THEREFLECTING SURFACE 40 INCHES (1016MM) MAXIMUM ABOVE THE FINISHFLOOR OR GROUND. MIRRORS NOT LOCATED ABOVE LAVATORIES ORCOUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THEREFLECTING SURFACE 35 INCHES (889MM) MAXIMUM ABOVE THE FINISH FLOOROR GROUND.11B-603.5ACCESSORIES.WHERE TOWEL OR SANITARY NAPKIN DISPENSERS,WASTE RECEPTACLES, OR OTHER ACCESSORIES ARE PROVIDED IN TOILETFACILITIES, AT LEAST ONE OF EACH TYPE SHALL BE LOCATED ON ANACCESSIBLE ROUTE. ALL OPERABLE PARTS, INCLUDING COIN SLOTS, SHALL BE40 INCHES (1016 MM) MAXIMUM ABOVE THE FINISH FLOOR.SIGNS11B-703 SIGNS11B-703.2 RAISED CHARACTERS.RAISED CHARACTERS SHALL COMPLY WITHSECTION 11B-703.2 AND SHALL BE DUPLICATED IN BRAILLE COMPLYING WITHSECTION 11B-703.3. RAISED CHARACTERS SHALL BE INSTALLED IN ACCORDANCEWITHSECTION 11B-703.4.11B-703.2.1 DEPTH.RAISED CHARACTERS SHALL BE 1/32 INCH (0.8 MM) MINIMUMABOVE THEIR BACKGROUND.11B-703.2.2 CASE.CHARACTERS SHALL BE UPPERCASE.11B-703.2.3 STYLE.CHARACTERS SHALL BE SANS SERIF. CHARACTERS SHALLNOT BE ITALIC, OBLIQUE, SCRIPT, HIGHLY DECORATIVE, OR OF OTHER UNUSUALFORMS.11B-703.2.4 CHARACTER PROPORTIONS. CHARACTERS SHALL BE SELECTEDFROM FONTS WHERE THE WIDTH OF THE UPPERCASE LETTER “O” IS60PERCENTMINIMUM AND 110 PERCENT MAXIMUM OF THE HEIGHT OF THE UPPERCASELETTER “I”.11B-703.2.5 CHARACTER HEIGHT.CHARACTER HEIGHT MEASURED VERTICALLYFROM THE BASELINE OF THE CHARACTER SHALL BE 5/8 INCH (15.9MM) MINIMUMAND 2 INCHES (51 MM) MAXIMUM BASED ON THE HEIGHT OF THE UPPERCASELETTER “I”.11B-703.2.6 STROKE THICKNESS.STROKE THICKNESS OF THE UPPERCASELETTER “I” SHALL BE 15 PERCENT MAXIMUM OF THE HEIGHT OF THE CHARACTER.11B-703.2.7 CHARACTER SPACING.CHARACTER SPACING SHALL BE MEASUREDBETWEEN THE TWO CLOSEST POINTS OF ADJACENT RAISED CHARACTERSWITHIN A MESSAGE, EXCLUDING WORD SPACES. WHERE CHARACTERS HAVERECTANGULAR CROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISEDCHARACTERS SHALL BE 1/8 INCH (3.2 MM) MINIMUM AND 4 TIMES THE RAISEDCHARACTER STROKE WIDTH MAXIMUM. WHERE CHARACTERS HAVE OTHERCROSS SECTIONS, SPACING BETWEEN INDIVIDUAL RAISED CHARACTERS SHALLBE 1/16 INCH (1.6 MM) MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKEWIDTH MAXIMUM AT THE BASE OF THE CROSS SECTIONS, AND 1/8 INCH (3.2 MM)MINIMUM AND 4 TIMES THE RAISED CHARACTER STROKE WIDTH MAXIMUM AT THETOP OF THE CROSS SECTIONS. CHARACTERS SHALL BE SEPARATED FROMRAISED BORDERS AND DECORATIVE ELEMENTS 3/8 INCH (9.5 MM) MINIMUM.11B-703.2.8 LINE SPACING.SPACING BETWEEN THE BASELINES OF SEPARATELINES OF RAISED CHARACTERS WITHIN A MESSAGE SHALL BE 135 PERCENTMINIMUM AND 170 PERCENT MAXIMUM OF THE RAISED CHARACTER HEIGHT.11B-703.4 INSTALLATION HEIGHT AND LOCATION.SIGNS WITH TACTILECHARACTERS SHALL COMPLY WITHSECTION 11B-703.4.11B-703.4.1 HEIGHT ABOVE FINISH FLOOR OR GROUND.TACTILE CHARACTERSON SIGNS SHALL BE LOCATED 48 INCHES (1219MM) MINIMUM ABOVE THE FINISHFLOOR OR GROUND SURFACE, MEASURED FROM THE BASELINE OF THE LOWESTBRAILLE CELLSAND 60 INCHES (1524MM) MAXIMUM ABOVE THE FINISH FLOOR ORGROUND SURFACE, MEASURED FROM THE BASELINE OF THE HIGHESTLINE OFRAISED CHARACTERS.11B-703.4.2 LOCATION.WHERE A TACTILE SIGN IS PROVIDED AT A DOOR, THESIGN SHALL BE LOCATED ALONGSIDE THE DOOR AT THE LATCH SIDE. WHERE ATACTILE SIGN IS PROVIDED AT DOUBLE DOORS WITH ONE ACTIVE LEAF, THE SIGNSHALL BE LOCATED ON THE INACTIVE LEAF. WHERE A TACTILE SIGN IS PROVIDEDAT DOUBLE DOORS WITH TWO ACTIVE LEAFS, THE SIGN SHALL BE LOCATED TOTHE RIGHT OF THE RIGHT HAND DOOR. WHERE THERE IS NO WALL SPACE AT THELATCH SIDE OF A SINGLE DOOR OR AT THE RIGHT SIDE OF DOUBLE DOORS,SIGNS SHALL BE LOCATED ON THE NEAREST ADJACENT WALL. SIGNSCONTAINING TACTILE CHARACTERS SHALL BE LOCATED SO THAT A CLEARFLOOR SPACE OF 18 INCHES (457MM) MINIMUM BY 18 INCHES (457MM) MINIMUM,CENTERED ON THE TACTILE CHARACTERS, IS PROVIDED BEYOND THE ARC OFANY DOOR SWING BETWEEN THE CLOSED POSITION AND 45 DEGREE OPENPOSITION.WHERE PERMANENT IDENTIFICATION SIGNAGE IS PROVIDED FORROOMS AND SPACES THEY SHALL BE LOCATED ON THE APPROACH SIDE OF THEDOOR AS ONE ENTERS THE ROOM OR SPACE. SIGNS THAT IDENTIFY EXITS SHALLBE LOCATED ON THE APPROACH SIDE OF THE DOOR AS ONE EXITS THE ROOMOR SPACE.2401 UTAH AVENUE SOUTHSEATTLE, WASHINGTON 98134(206) 318-1575SHEET NUMBER:SHEET TITLE:SCALE: AS SHOWNSTORE #:PROFILE TYPE:PROJECT #:ISSUE DATE:PROGRAM MANAGER:STORE DESIGNER:CHECKED BY:PROJECT NAME:PROJECT ADDRESS:STARBUCKS COFFEECOMPANYRLEED AP:© 2017 STARBUCKS COFFEE COMPANY®111 Pacifica, Suite 280, Irvine, CA 92618P: 949.553.1117 F: 949.474.7056San FranciscoClevelandDenverIrvineARCHITECT OF RECORDARCHITECT STAMP2017MCG PROJ. MANAGER:MCG PROJ. SPECIALIST:MCG PROJECT #:THESE DRAWINGS AND SPECIFICATIONS ARECONFIDENTIAL AND SHALL REMAIN THE SOLEPROPERTY OF STARBUCKS CORPORATION,WHICH IS THE OWNER OF THE COPYRIGHT INTHIS WORK. THEY SHALL NOT BEREPRODUCED (IN WHOLE OR IN PART), SHAREDWITH THIRD PARTIES OR USED IN ANY MANNERON OTHER PROJECTS OR EXTENSIONS TO THISPROJECT WITHOUT THE PRIOR WRITTENCONSENT OF STARBUCKS CORPORATION.THESE DRAWINGS AND SPECIFICATIONS AREINTENDED TO EXPRESS DESIGN INTENT FOR APROTOTYPICAL STARBUCKS STORE (WHICH ISSUBJECT TO CHANGE AT ANYTIME) AND DONOT REFLECT ACTUAL SITE CONDITIONS.NEITHER PARTY SHALL HAVE ANY OBLIGATIONNOR LIABILITY TO THE OTHER (EXCEPT STATEDABOVE) UNTIL A WRITTEN AGREEMENT ISFULLY EXECUTED BY BOTH PARTIES.mcg architecture8/30/2017 5:42:52 PMJ:\2016 Projects\0-Starbucks\16514_SBX-6970_El Dorado & Fremont_Stockton_CA (NS-RELO)\02-Arch\3-CD\1-Revit Files\16514_SBX-6970_El Dorado & Fremont_Stockton.rvtG-000421295-04208/18/17ELDORADO &FREMONT510NELDORADOSTREETSTOCKTON, CA 95202SANJOAQUIN COUNTYCORE6970CH. LINM. DARMOKOACCESSIBILITY NOTESC. LEEG. MONTALVO16514Revision ScheduleRev Date By Description
|