|
WOODS AND PLASTICS1.1 MATERIALSA. WOOD-PRESERVATIVE-TREATED LUMBER:1. PRESERVATIVE TREATMENT: AWPA U1; USE CATEGORY UC2, BUT USECATEGORY UC3B FOR EXTERIOR CONSTRUCTION AND USE CATEGORY UC4AFOR ITEMS IN CONTACT WITH THE GROUND.a. PRESERVATIVE CHEMICALS: CONTAINING NO ARSENIC ORCHROMIUM. DO NOT USE INORGANIC BORON (SBX) FOR SILL PLATES.2. APPLICATION: ITEMS INDICATED AND AS FOLLOWS:a. ITEMS IN CONTACT WITH ROOFING OR WATERPROOFING.b. ITEMS IN CONTACT WITH CONCRETE OR MASONRY.c. FRAMING LESS THAN 18 INCHES (460 MM) ABOVE GROUND INCRAWLSPACES.d. FLOOR PLATES INSTALLED OVER CONCRETE SLABS-ON-GRADE.B. DIMENSION LUMBER FRAMING:1. EXPOSED FRAMING: HAND-SELECTED FOR APPEARANCE AND FREEDOM FROMDECAY, HONEYCOMB, KNOT-HOLES, SHAKE, SPLITS, TORN GRAIN AND WANE.a. APPLICATION: EXPOSED EXTERIOR AND INTERIOR FRAMING INDICATED TORECEIVE A STAINED OR NATURAL FINISH.b. SPECIES AND GRADE: AS INDICATED FOR LOAD-BEARING CONSTRUCTION.C. ENGINEERED WOOD PRODUCTS, GENERAL: PRODUCTS LOCATED WITHIN THEBUILDING WEATHERPROOFING SYSTEM SHALL CONTAIN NO ADDED UREARMALDEHYDE.D. SHEAR WALL PANELS, GENERAL: PRODUCTS LOCATED WITHIN THE BUILDINGWEATHERPROOFING SYSTEM SHALL CONTAIN NO ADDED UREA FORMALDEHYDE.E. FASTENERS:[HOT-DIP GALVANIZED] [STAINLESS]STEEL WHERE EXPOSED TOWEATHER, IN GROUND CONTACT, IN CONTACT WITH TREATED WOOD, OR IN AREAOF HIGH RELATIVE HUMIDITY.F. METAL FRAMING ANCHORS:1. HOT-DIP GALVANIZED STEEL FOR INTERIOR LOCATIONS.2. HOT-DIP, HEAVY-GALVANIZED STEEL FOR TREATED LUMBER AND WHEREINDICATED.3. STAINLESS STEEL FOR EXTERIOR AND WHERE INDICATED.G. MISCELLANEOUS MATERIALS:1. SILL-SEALER GASKETS: [GLASS-FIBER INSULATION] [NEOPRENE FOAM].2. ADHESIVES SHALL HAVE A VOC CONTENT OF 70 G/L OR LESS WHENCALCULATED ACCORDING TO 40 CFR 59, SUBPART D (EPA METHOD 24).END OF SECTION 061000SECTION 061000 - ROUGH CARPENTRYWOODS AND PLASTICS1.1 MATERIALSA. WOOD-PRESERVATIVE-TREATED MATERIALS:1. PRESERVATIVE TREATMENT: AWPA U1; USE CATEGORY UC2.a. PRESERVATIVE CHEMICALS: CONTAINING NO ARSENIC OR CHROMIUM. DONOT USE INORGANIC BORON (SBX) FOR SILL PLATES.2. APPLICATION: ITEMS INDICATED AND THE FOLLOWING:a. ITEMS IN CONTACT WITH ROOFING OR WATERPROOFING.b. ITEMS IN CONTACT WITH CONCRETE OR MASONRY.c. FRAMING LESS THAN 18 INCHES (460 MM) ABOVE GROUND INCRAWLSPACES.d. FLOOR PLATES INSTALLED OVER CONCRETE SLABS-ON-GRADE.B. FIRE-RETARDANT-TREATED MATERIALS:1. EXTERIOR TYPE FOR EXTERIOR LOCATIONS AND WHERE INDICATED.2. INTERIOR TYPE A UNLESS OTHERWISE INDICATED.3. APPLICATION: ITEMS INDICATED AND THE FOLLOWING:a. FRAMING FOR RAISED PLATFORMS.b. CONCEALED BLOCKING.c. ROOF FRAMING AND BLOCKING.d. ITEMS IN CONTACT WITH ROOFING.e. PLYWOOD BACKING PANELS.C. FRAMING:1. NON-LOAD-BEARING INTERIOR PARTITIONS: CONSTRUCTION OR NO. 2GRADE.D. MISCELLANEOUS LUMBER:1. DIMENSION LUMBER: CONSTRUCTION OR NO. 2 GRADE.2. UTILITY SHELVING: 19 PERCENT MAXIMUM MOISTURE CONTENT.3. CONCEALED BOARDS: 19 PERCENT MAXIMUM MOISTURE CONTENT.E. PLYWOOD BACKING PANELS: EXPOSURE 1, C-D PLUGGED,[FIRE-RETARDANT TREATED].F. FASTENERS: HOT-DIP GALVANIZED STEEL WHERE EXPOSED TO WEATHER, INGROUND CONTACT, IN CONTACT WITH TREATED WOOD, OR IN AREA OF HIGHRELATIVE HUMIDITY.G. METAL FRAMING ANCHORS:1. METAL: GALVANIZED STEEL; HOT-DIP HEAVY GALVANIZED STEEL FORWOOD-PRESERVATIVE-TREATED LUMBER AND WHERE INDICATED.H. ADHESIVES: ADHESIVES SHALL HAVE A VOC CONTENT OF 70 G/L OR LESS WHENCALCULATED ACCORDING TO 40 CFR 59, SUBPART D (EPA METHOD 24).1.2 INSTALLATIONA. FURRING TO RECEIVE PLYWOOD OR HARDBOARD PANELING: 1-BY-3-INCH NOMINAL-SIZE (19-BY-63-MM ACTUAL-SIZE) FURRING AT 24 INCHES (610 MM) O.C.B. FURRING TO RECEIVE GYPSUM BOARD: 1-BY-2-INCH NOMINAL-SIZE (19-BY-38-MMACTUAL-SIZE) FURRING AT 16 INCHES (406 MM) O.C.END OF SECTION 061053SECTION 061053 - MISCELLANEOUS ROUGH CARPENTRYWOODS AND PLASTICS1.1 MATERIALSA. WOOD PRODUCTS, GENERAL:1. WOOD PANEL PRODUCTS LOCATED WITHIN THE BUILDING WEATHERPROOFINGSYSTEM SHALL CONTAIN NO ADDED UREA FORMALDEHYDE.B. PRESERVATIVE-TREATED PLYWOOD:1. PRESERVATIVE TREATMENT: AWPA U1; USE CATEGORY UC2, BUT USECATEGORY UC3B FOR EXTERIOR CONSTRUCTION AND USE CATEGORY UC4AFOR ITEMS IN CONTACT WITH THE GROUND.2. PRESERVATIVE CHEMICALS: CONTAINING NO ARSENIC OR CHROMIUM.3. APPLICATION: TREAT PLYWOOD IN CONTACT WITH MASONRY OR CONCRETEOR USED WITH ROOFING, FLASHING, VAPOR BARRIERS, AND WATERPROOFING.C. FIRE-RETARDANT-TREATED PLYWOOD:1. EXTERIOR TYPE FOR EXTERIOR LOCATIONS AND WHERE INDICATED.2. INTERIOR TYPE A, HIGH TEMPERATURE (HT) FOR ROOF SHEATHING AND WHEREINDICATED.3. INTERIOR TYPE A, UNLESS OTHERWISE INDICATED.4. APPLICATION: TREAT THE FOLLOWING:a. ROOF SHEATHING AT FIRE AND PARTY WALLS.b. WALL SHEATHING AT FIRE AND PARTY WALLS.c. ROOF SHEATHING.d. SUBFLOORING AND UNDERLAYMENT FOR RAISED PLATFORMS.D. FASTENERS:[HOT-DIP GALVANIZED] [STAINLESS]STEEL WHERE EXPOSED TOWEATHER, IN GROUND CONTACT, IN CONTACT WITH TREATED WOOD, OR IN AREAOF HIGH RELATIVE HUMIDITY.E. MISCELLANEOUS MATERIALS:1. ADHESIVES SHALL HAVE A VOC CONTENT OF 50 G/L OR LESS WHENCALCULATED ACCORDING TO 40 CFR 59, SUBPART D (EPA METHOD 24).1.2 INSTALLATIONA. WOOD STRUCTURAL PANEL:1. COMBINATION SUBFLOOR-UNDERLAYMENT:a.[GLUE AND NAIL] [NAIL]TO WOOD FRAMING.b. SCREW TO COLD-FORMED METAL FRAMING.2. SUBFLOORING:a.[GLUE AND NAIL] [NAIL] [NAIL OR STAPLE]TO WOOD FRAMING.b. SCREW TO COLD-FORMED METAL FRAMING.3. SHEATHING:a.[NAIL] [NAIL OR STAPLE]TO WOOD FRAMING.b. SCREW TO COLD-FORMED METAL FRAMING.4. UNDERLAYMENT:a.[NAIL] [NAIL OR STAPLE]TO SUBFLOORING.B. GYPSUM SHEATHING:1.[NAIL] [OR] [SCREW]TO WOOD FRAMING.2. SCREW TO COLD-FORMED METAL FRAMING.C. FIBERBOARD SHEATHING:1.[NAIL] [NAIL OR STAPLE]TO WOOD FRAMING.D. PARTICLEBOARD UNDERLAYMENT:1.[GLUE AND NAIL] [NAIL] [NAIL OR STAPLE]TO SUBFLOORING.E. HARDBOARD UNDERLAYMENT:1.[NAIL] [NAIL OR STAPLE]TO SUBFLOORING.END OF SECTION 061600SECTION 061600 - SHEATHINGWOODS AND PLASTICS1.1 SUMMARYA. SECTION INCLUDES:1. STRUCTURAL INSULATED PANELS.1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED. INCLUDE RATEDCAPACITIES, OPERATINGCHARACTERISTICS, AND FURNISHED SPECIALTIES ANDACCESSORIES.B. SUBMIT SHOP DRAWINGS TO INDICATE PROJECT LAYOUT AND ELEVATIONS,MENSIONS AND THICKNESS OF PANELS, CONNECTIONS, ALL PENETRATIONS,DETAILS AND LOCATION OF JOINTS AND GASKETS INCLUDING PANEL JOINTS ANDJOINTS REQUIRED FOR THERMAL MOVEMENT, SEALANTS AND GASKETS, METHODOF ANCHORAGE, NUMBER OF ANCHORS, SUPPORTS, REINFORCEMENT, TRIM,FLASHINGS, ACCESSORIES, MATERIALS AND FINISHES.C. COORDINATION DRAWINGS: WALL ELEVATIONS, PLANS, AND OTHER DETAILS,DRAWN TO SCALE, ON WHICH THE FOLLOWING ITEMS ARE SHOWN ANDCOORDINATED WITH EACH OTHER, USING INPUT FROM INSTALLERS OF THE ITEMSINVOLVED:1. ELECTRICAL AND PLUMBING WALL PENETRATIONS.2. IN-WALL CONDUIT.3. IN-WALL PIPING.D. PRODUCT TEST REPORTS: BASED ON EVALUATION OF COMPREHENSIVE TESTSPERFORMED BY A QUALIFIED TESTING AGENCY, FOR PANEL ASSEMBLIES.E. LABELS: SUBMIT COPY OF LABEL APPROVED BY INSPECTION AGENCY CERTIFYINGTHAT MANUFACTURE OF PANELS COMPLIES WITH SPECIFIED PERFORMANCECHARACTERISTICS AND PHYSICAL PROPERTIES.F. INSTRUCTIONS: SUBMIT MANUFACTURER’S INSTALLATION INSTRUCTIONS.1.3 MATERIALSA. STRUCTURAL INSULATED PANEL: A PRESSURE LAMINATED COMPOSITE PANELCONSISTING OF THE FOLLOWING.1. EXTERIOR FACES OF FORMALDEHYDE FREE ORIENTED STRAND BOARD.2. INTERNAL BLOCKING OF FORMALDEHYDE FEE ENGINEERED LUMBER.3. INSULATING CORE OF EXPANDED POLYSTYRENE.1.4 ACCESSORIESA. FASTENERS – SHALL BE #14 CORROSION RESISTANT SCREWS FOR JOINING OFPANELS AND ATTACHMENT OF PANEL TO FRAMES, ROOF AND CORNERS. INADDITION, ZINC GALVANIZED SCREWS, NAILS OR STAPLES SHALL BE USED FORSPLINE AND PLATE ATTACHMENTS. ALL FASTENERS AS SUPPLIED OR APPROVED BYPANEL MANUFACTURER FOLLOWING FASTENING REQUIREMENTS.B. CONSTRUCTION ADHESIVE: USE ADHESIVES THAT HAVE A VOC CONTENT OF 70 G/LOR LESS WHEN CALCULATED ACCORDING TO 40 CFR 59, SUBPART D(EPA METHOD 24).END OF SECTION 063000SECTION 063000 - STRUCTURAL INSULATED PANELSWOODS AND PLASTICS1.1 SUMMARYA. INTERIOR STANDING AND RUNNING TRIM.B. FLUSH WOOD PANELING AND WAINSCOTS.C. MELAMINE CABINETS.D. SOLID-SURFACING-MATERIAL COUNTERTOPS.E. CLOSET AND UTILITY SHELVING.1.2 QUALITY ASSURANCEA. QUALITY STANDARD: AWI.1.3 MATERIALSA. WOOD PRODUCTS: COMPLY WITH THE FOLLOWING:1. HARDBOARD: AHA A135.4, MADE WITH BINDER CONTAINING NO UREAFORMALDEHYDE.2. MEDIUM-DENSITY FIBERBOARD: ANSI A208.2, GRADE 130, MADE WITH BINDERCONTAINING NO UREA FORMALDEHYDE.3. MOISTURE RESISTANT MEDIUM-DENSITY FIBERBOARD: ANSI A208.2, GRADE MD,MR50, MADE WITH BINDER CONTAINING NO UREA FORMALDEHYDE.4. STRAW-BASED PARTICLEBOARD: ANSI A208.1, GRADE M-2, EXCEPT FORDENSITY, MADE WITH ADHESIVE CONTAINING NO UREA FORMALDEHYDE.5. SOFTWOOD PLYWOOD: DOC PS 16. VENEER-FACED PANEL PRODUCTS (HARDWOOD PLYWOOD): HPVA HP-1,MADE WITH ADHESIVE CONTAINING NO UREA FORMALDEHYDE.B. ADHESIVES, GENERAL: DO NOT USE ADHESIVES THAT CONTAIN UREAFORMALDEHYDE.C. VOC LIMITS FOR INSTALLATION ADHESIVES AND GLUES: USE INSTALLATIONADHESIVES THAT COMPLY WITH THE FOLLOWING LIMITS FOR VOC CONTENT WHENCALCULATED ACCORDING TO 40 CFR 59, SUBPART D (EPA METHOD 24):1. WOOD GLUES: 30 G/L.2. PANEL ADHESIVE: 50 G/L3. MULTIPURPOSE CONSTRUCTION ADHESIVE: 70 G/L4. CONTACT ADHESIVE: 80 G/L.a. SPECIAL PURPOSE: 250 G/LD. CLOSET AND UTILITY SHELVING:1. GRADE: ECONOMY.2. SHELF MATERIAL: 3/4-INCH(19-MM) THERMOSET DECORATIVE PANEL WITH PVCOR POLYESTER EDGE BANDING.3. CLEATS: 3/4-INCH(19-MM) PANEL PRODUCT.E. SHOP FINISHING:1. GRADE: SAME GRADE AS WOODWORK.2. EXTENT: ALL WOODWORK SHOP FINISHED.1.4 INSTALLATIONA. SCRIBE AND CUT MILLWORK TO FIT ADJOINING WORK, REFINISH CUT SURFACES,AND REPAIR DAMAGED FINISH AT CUTS.B. ANCHOR MILLWORK TO ANCHORS OR BLOCKING BUILT IN OR DIRECTLY ATTACHEDTO SUBSTRATES. SECURE WITH COUNTERSUNK, CONCEALED FASTENERS ANDBLIND NAILING AS REQUIRED FOR COMPLETE INSTALLATION. USE FINE FINISHINGNAILS OR FINISHING SCREWS FOR EXPOSED FASTENING, COUNTERSUNK ANDFILLED FLUSH WITH MILLWORK AND MATCHING FINAL FINISH IF TRANSPARENTFINISH IS INDICATED.C. CABINETS: INSTALL WITHOUT DISTORTION SO DOORS AND DRAWERS FITOPENINGS PROPERLY AND ARE ACCURATELY ALIGNED. ADJUST HARDWARE TOCENTER DOORS AND DRAWERS IN OPENINGS AND TO PROVIDE UNENCUMBEREDOPERATION. COMPLETE INSTALLATION OF HARDWARE AND ACCESSORY ITEMS ASINDICATED.1. INSTALL CABINETS WITH NO MORE THAN 1/8 INCH IN 96-INCH(3 MM IN2400-MM) SAG, BOW, OR OTHER VARIATION FROM A STRAIGHT LINE.D. COUNTERTOPS: ANCHOR SECURELY BY SCREWING THROUGH CORNER BLOCKSOF BASE CABINETS OR OTHER SUPPORTS INTO UNDERSIDE OF COUNTERTOP.1. ALIGN ADJACENT SOLID-SURFACING-MATERIAL COUNTERTOPS AND FORMSEAMS TO COMPLY WITH MANUFACTURER'S WRITTEN RECOMMENDATIONSUSING ADHESIVE IN COLOR TO MATCH COUNTERTOP. CAREFULLY DRESSJOINTS SMOOTH, REMOVE SURFACE SCRATCHES, AND CLEAN ENTIRESURFACE.2. INSTALL COUNTERTOPS WITH NO MORE THAN 1/8 INCH IN 96-INCH(3 MM IN 2400-MM) SAG, BOW, OR OTHER VARIATION FROM A STRAIGHT LINE.3. SECURE COVED BACKSPLASHES TO TOPS PER MANUFACTURESFABRICATION MANUAL AND TO WALLS WITH ADHESIVE.4. CALK SPACE BETWEEN BACKSPLASH AND WALL WITH SEALANT SPECIFIED INDIVISION 7 SECTION "JOINT SEALANTS."END OF SECTION 064000SECTION 064000 - INTERIOR ARCHITECTURAL WOODWORKWOODS AND PLASTICSPART 1 - GENERAL1.1 SUMMARYA. SECTION INCLUDES THE FOLLOWING:1. GLASS-FIBER REINFORCED PLASTIC (FRP) WALL PANELING.2. MOLDING, ADHESIVES, AND JOINT SEALANTS.1.2 PLASTIC SHEET PANELINGA. GLASS-FIBER-REINFORCED PLASTIC PANELING: GELCOAT-FINISHED, GLASS-FIBERREINFORCED PLASTIC PANELS COMPLYING WITH ASTM D 5319.1. LOW-EMITTING MATERIALS: PANELING SHALL COMPLY WITH THE TESTING ANDPRODUCT REQUIREMENTS OF THE CALIFORNIA DEPARTMENT OF HEALTHSERVICES' "STANDARD PRACTICE FOR THE TESTING OF VOLATILE ORGANICEMISSIONS FROM VARIOUS SOURCES USING SMALL-SCALE ENVIRONMENTALCHAMBERS."2. NOMINAL THICKNESS: NOT LESS THAN 0.09 INCHES.3. COLOR: WHITE.4. MOLDING COLOR: WHITE.5. SURFACE FINISH: MOLDED PEBBLE TEXTURE.B. UNREINFORCED POLYPROPYLENE PANELING: SOLID POLYPROPYLENE PANELSMADE FROM NO LESS THAN 80 PERCENT RECYCLED MATERIAL.1. LOW-EMITTING MATERIALS: PANELING SHALL COMPLY WITH THE TESTING ANDPRODUCT REQUIREMENTS OF THE CALIFORNIA DEPARTMENT OF PUBLICHEALTH'S (FORMERLY, THE CALIFORNIA DEPARTMENT OF HEALTH SERVICES')"STANDARD METHOD FOR THE TESTING AND EVALUATION OF VOLATILEORGANIC CHEMICAL EMISSIONS FROM INDOOR SOURCES USINGENVIRONMENTAL CHAMBERS."2. NOMINAL THICKNESS: NOT LESS THAN 0.09 INCHES.3. COLOR: WHITE.4. MOLDING COLOR: WHITE.5. SURFACE FINISH: MOLDED PEBBLE TEXTURE.1.3 ADHESIVESA. AS RECOMMENDED BY PLASTIC PANELING MANUFACTURER.1. VOC LIMIT: 50 G/L.1.4 ACCESSORIESA. TRIM ACCESSORIES: MANUFACTURER'S STANDARD ONE-PIECE VINYL EXTRUSIONSDESIGNED TO RETAIN AND COVER EDGES OF PANELS. PROVIDE DIVISION BARS,INSIDE CORNERS, OUTSIDE CORNERS, AND CAPS AS NEEDED TO CONCEAL EDGES.1. COLOR: WHITE.END OF SECTION 064400SECTION 064400 - PLASTIC PANELINGTHERMAL AND MOISTURE PROTECTION1.1 MATERIALSA. COLD-APPLIED, EMULSIFIED ASPHALT: VOC OF 250 G/L OR LESS.1.2 INSTALLATIONA. COLD-APPLIED, EMULSIFIED-ASPHALT DAMPPROOFING:1. CONCRETE FOUNDATIONS AND PARGED MASONRY FOUNDATION WALLS: TWOBRUSH OR SPRAY COATS, ONE FIBERED BRUSH OR SPRAY COAT, OR ONETROWEL COAT.2. UNPARGED MASONRY FOUNDATION WALLS: PRIMER AND TWO BRUSH ORSPRAY COATS, PRIMER AND ONE FIBERED BRUSH OR SPRAY COAT, OR PRIMERAND ONE ROWEL COAT.3. UNEXPOSED FACES OF CONCRETE RETAINING WALLS: ONE BRUSH OR SPRAYCOAT.4. UNEXPOSED FACES OF MASONRY RETAINING WALLS: PRIMER AND ONE BRUSHOR SPRAY COAT.5. MASONRY BACKUP FOR BRICK VENEER ASSEMBLIES: PRIMER AND ONE BRUSHOR SPRAY COAT.6. EXTERIOR FACE OF INNER WYTHE OF CAVITY WALLS: PRIMER AND ONE BRUSHOR SPRAY COAT.7. INTERIOR FACE OF SINGLE-WYTHE EXTERIOR MASONRY WALLS: PRIMER ANDONE BRUSH OR SPRAY COAT.END OF SECTION 071113SECTION 071113 - BITUMINOUS DAMPPROOFINGTHERMAL AND MOISTURE PROTECTION1.1 MATERIALSA. MODIFIED BITUMINOUS SHEET: MINIMUM 60-MIL (1.5-MM) NOMINAL THICKNESS.B. MODIFIED BITUMINOUS SHEET, FABRIC REINFORCED: MINIMUM 60-MIL (1.5-MM)NOMINAL THICKNESS.C. EPDM RUBBER SHEET WATERPROOFING: 60 MILS (1.5 MM) THICK, UNREINFORCED.D. BUTYL RUBBER SHEET WATERPROOFING:[60 MILS (1.5 MM)] [90 MILS (2.3 MM)][120 MILS (3.0 MM)]THICK, UNREINFORCED.E. AUXILIARY MATERIALS:1. PRIMER: WATERBORNE.2. METAL TERMINATION BARS: ALUMINUM.3. PROTECTION COURSE: AS RECOMMENDED BY MANUFACTURER.F. MOLDED-SHEET DRAINAGE PANELS: MOLDED-PLASTIC DRAINAGE CORE WITH A[NONWOVEN] [WOVEN]GEOTEXTILE FACING.G.[HIGH-CAPACITY, MOLDED-SHEET COLLECTOR-PANEL SYSTEM: MOLDED-PLASTICDRAINAGE CORE WITH A WOVEN GEOTEXTILE FACING; BY SAME MANUFACTURERAS MOLDED-SHEET DRAINAGE PANELS.]H. INSULATION: EXTRUDED-POLYSTYRENE BOARD.I. INSULATION DRAINAGE PANELS: EXTRUDED-POLYSTYRENE BOARD, WITHGROOVED DRAINAGE CHANNELS; FOR WALL INSTALLATION.1.2 INSTALLATIONA. MODIFIED BITUMINOUS SHEET: ONE-PLY APPLICATION.B. RUBBER SHEET: FULLY ADHERED, CEMENT SPLICE SEAMS.END OF SECTION 071300SECTION 071300 - WATERPROOFINGTHERMAL AND MOISTURE PROTECTION1.1 SUMMARYA. APPLICATIONS:1. PERIMETER INSULATION UNDER SLABS-ON-GRADE.2. PERIMETER WALL INSULATION (SUPPORTING BACKFILL).3. CONCEALED BUILDING INSULATION.4. VAPOR RETARDERS.5. SOUND ATTENUATION INSULATION.1.2 PERFORMANCE REQUIREMENTSA. PLENUM RATING: GLASS[SLAG-WOOL-FIBER/ROCK-WOOL]-FIBER INSULATIONRATED FOR RESISTANCE AGAINST EROSION AND MOLD GROWTH PER UL 181.1.3 MATERIALSA. INSULATION:1. ALL INSULATION MATERIALS LOCATED WITHIN THE WATERPROOF MEMBRANEMUST BE CERTIFIED AS LOW EMITTING. CERTIFICATION MUST BE BASED UPONTHE CALIFORNIA DEPARTMENT OF HEALTH SERVICES STANDARD PRACTICE FORTHE TESTING OF VOLATILE ORGANIC EMISSIONS FROM VARIOUS SOURCESUSING SMALL-SCALE ENVIRONMENTAL CHAMBERS, INCLUDING 2004 ADDENDAOR A JURISDICTIONALLY RECOGNIZED STANDARD USING EQUIVALENT TESTINGMETHODOLOGIES AND VOC THRESHOLDS.B. VAPOR RETARDERS:[POLYETHYLENE] [REINFORCED POLYETHYLENE][FIRE-RETARDANT, REINFORCED POLYETHYLENE] [FOIL-POLYESTER FILM].END OF SECTION 072100SECTION 072100 - BUILDING INSULATIONTHERMAL AND MOISTURE PROTECTION1.1 MATERIALSA.[BUILDING PAPER: NO. 15 ASPHALT-SATURATED ORGANIC FELT, UNPERFORATED.][BUILDING PAPER: WATER-VAPOR-PERMEABLE , ASPHALT-SATURATED KRAFTBUILDING PAPER.][BUILDING WRAP: WITH FLAME-SPREAD AND SMOKE-DEVELOPEDINDEXES OF LESS THAN 25 AND 450, RESPECTIVELY, WHEN TESTED ACCORDINGTO ASTM E 84; UV STABILIZED; AND ACCEPTABLE TO AUTHORITIES HAVINGJURISDICTION.]B. BUILDING-WRAP TAPE: PRESSURE-SENSITIVE PLASTIC TAPE RECOMMENDED BYBUILDING-WRAP MANUFACTURER FOR SEALING JOINTS AND PENETRATIONS INBUILDING WRAP.C. FLEXIBLE FLASHING:[BUTYL RUBBER] [OR] [RUBBERIZED ASPHALT].END OF SECTION 072500SECTION 072500 - WEATHER BARRIERS2401 UTAH AVENUE SOUTHSEATTLE, WASHINGTON 98134(206) 318-1575SHEET NUMBER:SHEET TITLE:SCALE: AS SHOWNSTORE #:PROFILE TYPE:PROJECT #:ISSUE DATE:PROGRAM MANAGER:STORE DESIGNER:CHECKED BY:PROJECT NAME:PROJECT ADDRESS:STARBUCKS COFFEECOMPANYRLEED AP:© 2017 STARBUCKS COFFEE COMPANY®111 Pacifica, Suite 280, Irvine, CA 92618P: 949.553.1117 F: 949.474.7056San FranciscoClevelandDenverIrvineARCHITECT OF RECORDARCHITECT STAMP2017MCG PROJ. MANAGER:MCG PROJ. SPECIALIST:MCG PROJECT #:THESE DRAWINGS AND SPECIFICATIONS ARECONFIDENTIAL AND SHALL REMAIN THE SOLEPROPERTY OF STARBUCKS CORPORATION,WHICH IS THE OWNER OF THE COPYRIGHT INTHIS WORK. THEY SHALL NOT BEREPRODUCED (IN WHOLE OR IN PART), SHAREDWITH THIRD PARTIES OR USED IN ANY MANNERON OTHER PROJECTS OR EXTENSIONS TO THISPROJECT WITHOUT THE PRIOR WRITTENCONSENT OF STARBUCKS CORPORATION.THESE DRAWINGS AND SPECIFICATIONS AREINTENDED TO EXPRESS DESIGN INTENT FOR APROTOTYPICAL STARBUCKS STORE (WHICH ISSUBJECT TO CHANGE AT ANYTIME) AND DONOT REFLECT ACTUAL SITE CONDITIONS.NEITHER PARTY SHALL HAVE ANY OBLIGATIONNOR LIABILITY TO THE OTHER (EXCEPT STATEDABOVE) UNTIL A WRITTEN AGREEMENT ISFULLY EXECUTED BY BOTH PARTIES.mcg architecture8/30/2017 5:43:21 PMJ:\2016 Projects\0-Starbucks\16514_SBX-6970_El Dorado & Fremont_Stockton_CA (NS-RELO)\02-Arch\3-CD\1-Revit Files\16514_SBX-6970_El Dorado & Fremont_Stockton.rvtG-001021295-04208/18/17ELDORADO &FREMONT510NELDORADOSTREETSTOCKTON, CA 95202SANJOAQUIN COUNTYCORE6970CH. LINM. DARMOKOOUTLINESPECIFICATIONSC. LEEG. MONTALVO16514Revision ScheduleRev Date By Description
|