|
FINISHES1.1 SUMMARYA. NON-LOAD-BEARING STEEL FRAMING MEMBERS FOR INTERIOR FRAMINGSYSTEMS.1.2 MATERIALSA. STEEL FRAMING FOR FRAMED ASSEMBLIES:B. FRAMING MEMBERS, GENERAL: COMPLY WITH ASTM C 754 FOR CONDITIONSINDICATED.1. STEEL SHEET COMPONENTS: COMPLY WITH ASTM C 645 REQUIREMENTS FORMETAL, UNLESS OTHERWISE INDICATED.2. PROTECTIVE COATING: COATING WITH EQUIVALENT CORROSION RESISTANCEOF ASTM A 653/A 653M, G40 (Z120), HOT-DIP GALVANIZED, UNLESS OTHERWISEINDICATED.1.3 STEEL FRAMING FOR FRAMED ASSEMBLIESA. SALVAGED MATERIAL: USE SALVAGED FRAMING MATERIALS WHENEVER AVAILABLE.B. STEEL STUDS AND RUNNERS: ASTM C 645.1. MINIMUM BASE-METAL THICKNESS: 0.033 INCH (0.84 MM) UNLESSOTHERWISE INDICATED ON DRAWINGS.2. DEPTH: AS INDICATED ON DRAWINGS.C. DIMPLED STEEL STUDS AND RUNNERS:1. MINIMUM BASE-METAL THICKNESS: 0.025 INCH (0.64 MM).2. DEPTH: AS INDICATED ON DRAWINGS.D. SLIP-TYPE HEAD JOINTS: WHERE INDICATED, PROVIDE ONE OF THE FOLLOWING:1. SINGLE LONG-LEG RUNNER SYSTEM: ASTM C 645 TOP RUNNER WITH2-INCH- (50.8-MM-) DEEP FLANGES IN THICKNESS NOT LESS THAN INDICATEDFOR STUDS, INSTALLED WITH STUDS FRICTION FIT INTO TOP RUNNER AND WITHCONTINUOUS BRIDGING LOCATED WITHIN 12 INCHES (305 MM) OF THE TOP OFSTUDS TO PROVIDE LATERAL BRACING.2. DOUBLE-RUNNER SYSTEM: ASTM C 645 TOP RUNNERS, INSIDE RUNNER WITH2-INCH- (50.8-MM-) DEEP FLANGES IN THICKNESS NOT LESS THAN INDICATEDFOR STUDS AND FASTENED TO STUDS, AND OUTER RUNNER SIZED TO FRICTIONFIT INSIDE RUNNER.3. DEFLECTION TRACK: STEEL SHEET TOP RUNNER MANUFACTURED TO PREVENTCRACKING OF FINISHES APPLIED TO INTERIOR PARTITION FRAMING RESULTINGFROM DEFLECTION OF STRUCTURE ABOVE; IN THICKNESS NOT LESS THANINDICATED FOR STUDS AND IN WIDTH TO ACCOMMODATE DEPTH OF STUDS.E. COLD-ROLLED CHANNEL BRIDGING: 0.0538-INCH (1.37-MM) BARE-STEEL THICKNESS,WITH MINIMUM 1/2-INCH- (12.7-MM-) WIDE FLANGES.1. DEPTH: 1-1/2 INCHES (38.1 MM).2. CLIP ANGLE: NOT LESS THAN 1-1/2 BY 1-1/2 INCHES (38.1 BY 38.1 MM),0.068-INCH- (1.73-MM-) THICK, GALVANIZED STEEL.F. HAT-SHAPED, RIGID FURRING CHANNELS: ASTM C 645.1. MINIMUM BASE METAL THICKNESS: AS INDICATED ON DRAWINGS.2. DEPTH: AS INDICATED ON DRAWINGS.G. COLD-ROLLED FURRING CHANNELS: 0.0538-INCH (1.37-MM) BARE-STEEL THICKNESS,WITH MINIMUM 1/2-INCH- (12.7-MM-) WIDE FLANGES.1. DEPTH: AS INDICATED ON DRAWINGS.2. FURRING BRACKETS: ADJUSTABLE, CORRUGATED-EDGE TYPE OF STEEL SHEETWITH MINIMUM BARE-STEEL THICKNESS OF 0.0312 INCH (0.79 MM).3. TIE WIRE: ASTM A 641/A 641M, CLASS 1 ZINC COATING, SOFT TEMPER,0.0625-INCH- (1.59-MM-) DIAMETER WIRE, OR DOUBLE STRAND OF0.0475-INCH- (1.21-MM-) DIAMETER WIRE.H. Z-SHAPED FURRING: WITH SLOTTED OR NONSLOTTED WEB, FACE FLANGE OF1-1/4 INCHES (31.8 MM), WALL ATTACHMENT FLANGE OF 7/8 INCH (22.2 MM), MINIMUMBARE-METAL THICKNESS OF 0.0179 INCH (0.45 MM), AND DEPTH REQUIRED TO FITINSULATION THICKNESS INDICATED.END OF SECTION 092216SECTION 092216 - NON-STRUCTURAL STEEL FRAMINGFINISHES1.1 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED.B. SAMPLES FOR VERIFICATION: FOR EACH TYPE OF FACTORY-PREPARED FINISHCOAT INDICATED; 12 BY 12 INCHES (305 BY 305 MM), AND PREPARED ON RIGIDBACKING.1.2 MATERIALSA. METAL LATH:1. EXPANDED-METAL LATH: SELF-FURRING DIAMOND-MESH WITH HOT-DIPGALVANIZED-ZINC COATING.2. WELDED-WIRE LATH: SELF-FURRING.3. PAPER BACKING: PROVIDE AT EXTERIOR LOCATIONS.B. ACCESSORIES:1. FOUNDATION WEEP SCREED: HOT-DIP GALVANIZED STEEL SHEET.2. CORNERITE: FABRICATED FROM METAL LATH WITH HOT-DIP GALVANIZED-ZINCCOATING.3. EXTERNAL-OUTSIDE-CORNER REINFORCEMENT: FABRICATED FROM METALLATH WITH HOT-DIP GALVANIZED-ZINC COATING.4. CASING BEADS: FABRICATED FROM ZINC OR ZINC-COATED (GALVANIZED) STEEL;SQUARE-EDGED STYLE; WITH EXPANDED FLANGES.5. CONTROL JOINTS: FABRICATED FROM ZINC OR ZINC-COATED (GALVANIZED)STEEL; ONE-PIECE-TYPE, FOLDED PAIR OF UNPERFORATED SCREEDS IN M-SHAPED CONFIGURATION; WITH PERFORATED FLANGES AND REMOVABLEPROTECTIVE TAPE ON PLASTER FACE OF CONTROL JOINT.6. EXPANSION JOINTS: FABRICATED FROM ZINC OR ZINC-COATED (GALVANIZED)STEEL; FOLDED PAIR OF UNPERFORATED SCREEDS IN M-SHAPEDCONFIGURATION; WITH EXPANDED FLANGES.7. TWO-PIECE EXPANSION JOINTS: FABRICATED FROM ZINC OR ZINC-COATED(GALVANIZED) STEEL; FORMED TO PRODUCE SLIP-JOINT AND SQUARE-EDGEDREVEAL THAT IS ADJUSTABLE FROM 1/4 TO 5/8 INCH (6 TO 16 MM) WIDE; WITHPERFORATED FLANGES.C. FIBER FOR BASE COAT: ALKALINE-RESISTANT GLASS OR POLYPROPYLENEFIBERS, 1/2 INCH(13 MM) LONG, FREE OF CONTAMINANTS, MANUFACTURED FORUSE IN CEMENT PLASTER.D. WIRE: ASTM A 641/A 641M, CLASS 1 ZINC COATING, SOFT TEMPER, NOT LESS THAN0.0475-INCH (1.21-MM) DIAMETER UNLESS OTHERWISE INDICATED.E. PLASTER MATERIALS: PORTLAND CEMENT WITH SAND AGGREGATE.F. COLORANTS FOR JOB-MIXED FINISH COATS: COLORFAST MINERAL PIGMENTS THATPRODUCE FINISH PLASTER COLOR.G. PLASTER MIXES: ASTM C 926.1.3 INSTALLATION:A. PLASTER FINISH COATS: APPLY TO PROVIDE SMOOTH TEXTURED FINISH.END OF SECTION 092400SECTION 092400 – PORTLAND CEMENT PLASTERINGFINISHES1.1 SUMMARYA. INTERIOR GYPSUM BOARD.B. TILE BACKING PANELS.1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED.B. SAMPLES: FOR THE FOLLOWING PRODUCTS:1. TEXTURED FINISHES: MANUFACTURER'S STANDARD SIZE FOR EACH TEXTUREDFINISH INDICATED AND ON SAME BACKING INDICATED FOR WORK.1.3 MATERIALSA. INTERIOR GYPSUM BOARD:1. GENERAL: COMPLYING WITH ASTM C 36/C 36M OR ASTM C 1396/C 1396M, ASAPPLICABLE TO TYPE OF GYPSUM BOARD INDICATED AND WHICHEVER IS MORESTRINGENT.a. MUST BE CERTIFIED AS LOW EMITTING. CERTIFICATION MUST BE BASEDUPON THE CALIFORNIA DEPARTMENT OF HEALTH SERVICES STANDARDPRACTICE FOR THE TESTING OF VOLATILE ORGANIC EMISSIONS FROMVARIOUS SOURCES USING SMALL-SCALE ENVIRONMENTAL CHAMBERS,INCLUDING 2004 ADDENDA OR A JURISDICTIONALLY RECOGNIZED STANDARDUSING EQUIVALENT TESTING METHODOLOGIES AND VOC THRESHOLDS.2. TYPE X:a. THICKNESS: 5/8 INCH (15.9 MM).b. LONG EDGES: TAPERED.3. MOISTURE- AND MOLD-RESISTANT TYPE: WITH MOISTURE- AND MOLD-RESISTANT CORE AND SURFACES.a. CORE: 5/8 INCH(15.9 MM), TYPE X.b. LONG EDGES: TAPERED.c. MOLD RESISTANCE: ASTM D 3273, SCORE OF 10 AS RATED ACCORDING TOASTM D 3274.B. TILE-BACKING PANELS:1. GLASS-MAT, WATER-RESISTANT BACKING BOARD: ASTM C 1178/C 1178M, WITHMANUFACTURER'S STANDARD EDGES.a. MUST BE CERTIFIED AS LOW EMITTING. CERTIFICATION MUST BE BASEDUPON THE CALIFORNIA DEPARTMENT OF HEALTH SERVICES STANDARDPRACTICE FOR THE TESTING OF VOLATILE ORGANIC EMISSIONS FROMVARIOUS SOURCES USING SMALL-SCALE ENVIRONMENTAL CHAMBERS,INCLUDING 2004 ADDENDA OR A JURISDICTIONALLY RECOGNIZED STANDARDUSING EQUIVALENT TESTING METHODOLOGIES AND VOC THRESHOLDS.b. CORE: 5/8 INCH (15.9 MM), TYPE X.c. MOLD RESISTANCE: ASTM D 3273, SCORE OF 10 AS RATED ACCORDING TOASTM D 3274.2. CEMENTITIOUS BACKER UNITS: ANSI A118.9 AND ASTM C 1288 OR 1325, WITHMANUFACTURER'S STANDARD EDGES.a. THICKNESS:[1/4 INCH (6.4 MM)] [AS INDICATED].b. MOLD RESISTANCE: ASTM D 3273, SCORE OF 10 AS RATED ACCORDING TOASTM D 3274.C. TRIM ACCESSORIES:a. INTERIOR: CORNERBEAD.END OF SECTION 092900SECTION 092900 - GYPSUM BOARDFINISHES1.1 SUMMARYA. PAVER, GLAZED, AND WALL TILE.B. WATERPROOF MEMBRANE FOR THIN-SET TILE INSTALLATIONS.C. METAL EDGE STRIPS INSTALLED AS PART OF TILE INSTALLATIONS.1.2 QUALITY ASSURANCEA. MOCKUPS FOR EACH FORM OF CONSTRUCTION.1.3 MATERIALSA. GLAZED WALL TILE TRIM SHAPES: COVED BASE, BULLNOSE CAP.B. THRESHOLDS: SATIN ANODIZED ALUMINUM THRESHOLDS AND TRANSITION STRIPS.1. BEVEL EDGES AT 1:2 SLOPE, WITH LOWER EDGE OF BEVEL ALIGNED WITH ORUP TO 1/16 INCH (1.5 MM) ABOVE ADJACENT FLOOR SURFACE. FINISH BEVEL TOMATCH TOP SURFACE OF THRESHOLD. LIMIT HEIGHT OF THRESHOLD TO1/2 INCH (12.7 MM) OR LESS ABOVE ADJACENT FLOOR SURFACE.C. MORTAR: LATEX-PORTLAND CEMENTD. ELASTOMERIC SEALANTS: ONE-PART, MILDEW-RESISTANT SILICONE.1. SEALANTS SHALL HAVE A VOC CONTENT OF 250 G/L OR LESS WHENCALCULATED ACCORDING TO 40 CFR 59, SUBPART D (EPA METHOD 24).1.4 FLOOR TILE INSTALLATION SCHEDULEA. INTERIOR FLOORS ON CONCRETE: THIN-SET MORTAR.1. TILE TYPE: UNGLAZED PAVER TILE.2. MORTAR: LATEX- PORTLAND CEMENT MORTAR BOND COAT.3. GROUT: POLYMER-MODIFIED UNSANDED 100% SOLIDS EPOXY NON-SAGGINGGROUT.B. INTERIOR FLOORS ON [WATERPROOF] [CRACK-SUPPRESSION] MEMBRANE OVERCONCRETE AND WOOD: THIN-SET MORTAR.1. TILE TYPE: UNGLAZED PAVER TILE.2. MORTAR: LATEX- PORTLAND CEMENT MORTAR BOND COAT.3. GROUT: POLYMER-MODIFIED UNSANDED 100% SOLIDS EPOXY NON-SAGGINGGROUT.1.5 WALL TILE INSTALLATION SCHEDULEA. INTERIOR WALLS OVER GLASS-MAT WATER-RESISTANT BACKER BOARD ORCEMENTITIOUS BACKER UNITS: THIN-SET MORTAR.1. MORTAR: LATEX- PORTLAND CEMENT MORTAR.2. GROUT: POLYMER-MODIFIED UNSANDED GROUT SUPPLIED BY GC.1.6 INSTALLATIONA. ALL TILE AND SLATE TO BE INSTALLED PER TILE COUNCIL OF AMERICA STANDARDS.END OF SECTION 093000SECTION 093000 - TILINGFINISHES1.1 SUMMARYA. ACOUSTICAL PANELS AND EXPOSED SUSPENSION SYSTEMS.1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED.B. COORDINATION DRAWINGS: REFLECTED CEILING PLANS, DRAWN TO SCALE, ONWHICH THE FOLLOWING ITEMS ARE SHOWN AND COORDINATED WITH EACH OTHER,BASED ON INPUT FROM INSTALLERS OF THE ITEMS INVOLVED:1. CEILING SUSPENSION SYSTEM MEMBERS.2. METHOD OF ATTACHING HANGERS TO BUILDING STRUCTURE.3. CEILING-MOUNTED ITEMS INCLUDING LIGHTING FIXTURES, DIFFUSERS, GRILLES,SPEAKERS, SPRINKLERS, ACCESS PANELS, AND SPECIAL MOLDINGS.C. SAMPLES FOR VERIFICATION: FOR EACH COMPONENT INDICATED AND FOR EACHEXPOSED FINISH REQUIRED, PREPARED ON SAMPLES OF SIZE INDICATED BELOW.1. ACOUSTICAL PANEL: SET OF FULL-SIZE SAMPLES OF EACH TYPE, COLOR,PATTERN, AND TEXTURE.2. EXPOSED SUSPENSION SYSTEM MEMBERS, MOLDINGS, AND TRIM: SET OF12-INCH-(300-MM-) LONG SAMPLES OF EACH TYPE, FINISH, AND COLOR.D. QUALIFICATION DATA: FOR TESTING AGENCY.E. FIELD QUALITY-CONTROL TEST REPORTS.F. PRODUCT TEST REPORTS: BASED ON EVALUATION OF COMPREHENSIVE TESTSPERFORMED BY A QUALIFIED TESTING AGENCY, FOR EACH ACOUSTICAL PANELCEILING.G. MAINTENANCE DATA: FOR FINISHES TO INCLUDE IN MAINTENANCE MANUALS.1.3 QUALITY ASSURANCEA. ACOUSTICAL PANEL QUALITY STANDARD: ASTM E 1264.B. METAL SUSPENSION SYSTEM QUALITY STANDARD: ASTM C 635.1.4 MATERIALSA. ACOUSTICAL CEILING PANELS GENERAL: MUST BE CERTIFIED AS LOW EMITTING.CERTIFICATION MUST BE BASED UPON THE CALIFORNIA DEPARTMENT OF HEALTHSERVICES STANDARD PRACTICE FOR THE TESTING OF VOLATILE ORGANICEMISSIONS FROM VARIOUS SOURCES USING SMALL-SCALE ENVIRONMENTALCHAMBERS, INCLUDING 2004 ADDENDA OR A JURISDICTIONALLY RECOGNIZEDSTANDARD USING EQUIVALENT TESTING METHODOLOGIES AND VOC THRESHOLDS.B. ACOUSTICAL CEILING PANELS WASHABLE1. CLASSIFICATION: TYPE IV, MINERAL BASE WITH MEMBRANE-FACED OVERLAY;FORM 2, WATER FELTED; WITH VINYL OVERLAY ON FACE; PATTERN G (SMOOTH).2. COLOR: AS INDICATED ON DRAWINGS.3. THICKNESS: 5/8 INCH (15 MM).4. MODULAR SIZE: 24 BY 48 INCHES (610 BY 1220 MM).5. BROAD SPECTRUM ANTIMICROBIAL FUNGICIDE AND BACTERICIDE TREATMENT:PROVIDE ACOUSTICAL TILES TREATED WITH MANUFACTURER'S STANDARDANTIMICROBIAL FORMULATION THAT INHIBITS FUNGUS, MOLD, MILDEW, ANDGRAM-POSITIVE AND GRAM-NEGATIVE BACTERIA AND SHOWING NO MOLD,MILDEW, OR BACTERIAL GROWTH WHEN TESTED ACCORDING TO ASTM D 3273AND EVALUATED ACCORDING TO ASTM D 3274 OR ASTM G 21.C. ACOUSTICAL CEILING PANELS TEXTURED:1. CLASSIFICATION: TYPE III, MINERAL BASE WITH PAINTED FINISH; FORM2, WATERFELTED; PATTERN E (LIGHTLY TEXTURED).2. COLOR: AS INDICATED ON DRAWINGS.3. THICKNESS: 5/8 INCH (15 MM).4. MODULAR SIZE: 24 BY 48 INCHES (610 BY 1220 MM).5. BROAD SPECTRUM ANTIMICROBIAL FUNGICIDE AND BACTERICIDE TREATMENT:PROVIDE ACOUSTICAL TILES TREATED WITH MANUFACTURER'S STANDARDANTIMICROBIAL FORMULATION THAT iNHIBITS FUNGUS, MOLD, MILDEW, ANDGRAM-POSITIVE AND GRAM-NEGATIVE BACTERIA AND SHOWING NO MOLD,MILDEW, OR BACTERIAL GROWTH WHEN TESTED ACCORDING TO ASTM D 3273AND EVALUATED ACCORDING TO ASTM D 3274 OR ASTM G 21.D. ACOUSTICAL CEILING PANELS PERFORATED:1. CLASSIFICATION: TYPE III, MINERAL BASE WITH PAINTED FINISH; FORM 2,WATER FELTED; PATTERN CE (PERFORATED, SMALL HOLES AND LIGHTLYTEXTURED).2. COLOR: AS INDICATED ON DRAWINGS.3. THICKNESS: 3/4 INCH(15 MM).4. MODULAR SIZE: 24 BY 48 INCHES(610 BY 1220 MM).5. BROAD SPECTRUM ANTIMICROBIAL FUNGICIDE AND BACTERICIDE TREATMENT:PROVIDE ACOUSTICAL TILES TREATED WITH MANUFACTURER'S STANDARDANTIMICROBIAL FORMULATION THAT INHIBITS FUNGUS, MOLD, MILDEW, ANDGRAM-POSITIVE AND GRAM-NEGATIVE BACTERIA AND SHOWING NO MOLD,MILDEW, OR BACTERIAL GROWTH WHEN TESTED ACCORDING TO ASTM D 3273AND EVALUATED ACCORDING TO ASTM D 3274 OR ASTM G 21.E. METAL SUSPENSION SYSTEMS:1. WIDE-FACE, CAPPED, DOUBLE-WEB STEEL: INTERMEDIATE DUTY.F. METAL EDGE MOLDINGS AND TRIM: ROLL-FORMED SHEET METAL.1.5 INSTALLATIONA. INSTALLATION: ASTM C 636.1.6 FIELD QUALITY CONTROLA. TESTING: BY OWNER-ENGAGED AGENCY TO TEST ACOUSTICAL PANEL CEILINGHANGER FASTENERS.END OF SECTION 095113SECTION 095113 - ACOUSTICAL PANEL CEILINGSFINISHES1.1 COMPONENTSA. MOLDINGS AND TRIM.B. SEISMIC STRUTS.C. HOLD-DOWN CLIPS.D. ALUMINUM PANS AND SUSPENSION SYSTEM:1. PRODUCTS: SUBJECT TO COMPLIANCE WITH REQUIREMENTS:a. BESTWORTH ROMMEL; ALPOLIC ACM PANELS.2. CLASSIFICATION: UNPERFORATED.3. LINEAR MODULE WIDTH:[2 INCHES(51 MM)] [4 INCHES(102 MM)] [6 INCHES(152 MM)] [8 INCHES(203 MM)] <INSERT DIMENSIONS>.4. PAN DEPTH:[5/8 INCH(16 MM)] [3/4 INCH(19 MM)] [1 TO 1-1/2 INCHES(25 TO 38 MM)] <INSERT DEPTH>.5. PAN FACE FINISH:[MILL] [LACQUERED MILL] [CLEAR ANODIZED][CLEAR MIRROR-ANODIZED] [PAINTED] [FLUOROPOLYMER COATED][BRIGHT REFLECTIVE] <INSERT FINISH>.6. FILLER STRIP.7. SUSPENSION-SYSTEM MAIN-CARRIER MATERIAL: ALUMINUM.END OF SECTION 095423SECTION 095423 - LINEAR METAL CEILINGSFINISHES1.1 PERFORMANCE REQUIREMENTSA. FLOORSCORE COMPLIANCE: COMPOSITE WOOD FLOORS SHALL COMPLY WITHREQUIREMENTS OF FLOORSCORE STANDARD.1.2 MATERIALSA. ACCESSORIES:1. WOOD FLOORING ADHESIVE: VOC LIMITS: 100 G/L.END OF SECTION 096400SECTION 096400 - WOOD FLOORINGFINISHES1.1 PRODUCTSA. FLOORING SYSTEM: FLOORSCORE COMPLIANCE.B. VINYL SHEET FLOORING:1. BACKING: NONE, UNBACKED.2. SEAMLESS-INSTALLATION METHOD: HEAT WELDED.C. RUBBER SHEET FLOORING:1. BACKING: NONE, UNBACKED.2. SEAMLESS-INSTALLATION METHOD: HEAT WELDED.D. INSTALLATION MATERIALS:E. TROWELABLE LEVELING AND PATCHING COMPOUNDS: LATEX-MODIFIED, PORTLANDCEMENT BASED OR BLENDED HYDRAULIC-CEMENT-BASED FORMULATION PROVIDEDOR APPROVED BY RESILIENT SHEET FLOORING MANUFACTURER FOR APPLICATIONSINDICATED.F. ADHESIVES: WATER-RESISTANT TYPE RECOMMENDED BY FLOORING ANDADHESIVE MANUFACTURERS TO SUIT RESILIENT SHEET FLOORING AND SUBSTRATECONDITIONS INDICATED.1. VINYL SHEET ADHESIVES SHALL HAVE A VOC CONTENT OF 50 G/L OR LESS.2. RUBBER SHEET ADHESIVES SHALL HAVE A VOC CONTENT OF 60 G/L OR LESS.G. INTEGRAL-FLASH-COVE-BASE ACCESSORIES:1. COVE STRIP: 1-INCH (25-MM) RADIUS PROVIDED OR APPROVED BY RESILIENTSHEET FLOORING MANUFACTURER.2. CAP STRIP:[SQUARE METAL, VINYL, OR RUBBER CAP] [TAPERED VINYL CAP]PROVIDED OR APPROVED BY RESILIENT SHEET FLOORING MANUFACTURER.3. FLOOR POLISH: PROVIDE PROTECTIVE, LIQUID FLOOR-POLISH PRODUCTSRECOMMENDED BY RESILIENT SHEET FLOORING MANUFACTURER.END OF SECTION 096516SECTION 096516 - RESILIENT SHEET FLOORINGFINISHES1.1 QUALITY ASSURANCEA. PRODUCTS COMPLY WITH REQUIREMENTS OF CRI'S GREEN LABEL INDOOR AIRQUALITY TESTING PROGRAM.1.2 WARRANTYA. CARPET TILE: ONE YEAR.1.3 MATERIALSA. ADHESIVES: WATER-RESISTANT, MILDEW-RESISTANT, NONSTAINING,PRESSURE-SENSITIVE TYPE TO SUIT PRODUCTS AND SUBFLOOR CONDITIONSINDICATED, THAT COMPLIES WITH FLAMMABILITY REQUIREMENTS FOR INSTALLEDCARPET TILE AND IS RECOMMENDED BY CARPET TILE MANUFACTURER FORRELEASABLE INSTALLATION.a. VOC LIMITS: 50 G/L1.4 INSTALLATIONA. INSTALLATION METHOD: GLUE DOWN WITH RELEASABLE ADHESIVE.END OF SECTION 096813SECTION 096813 – TILE CARPETING2401 UTAH AVENUE SOUTHSEATTLE, WASHINGTON 98134(206) 318-1575SHEET NUMBER:SHEET TITLE:SCALE: AS SHOWNSTORE #:PROFILE TYPE:PROJECT #:ISSUE DATE:PROGRAM MANAGER:STORE DESIGNER:CHECKED BY:PROJECT NAME:PROJECT ADDRESS:STARBUCKS COFFEECOMPANYRLEED AP:© 2017 STARBUCKS COFFEE COMPANY®111 Pacifica, Suite 280, Irvine, CA 92618P: 949.553.1117 F: 949.474.7056San FranciscoClevelandDenverIrvineARCHITECT OF RECORDARCHITECT STAMP2017MCG PROJ. MANAGER:MCG PROJ. SPECIALIST:MCG PROJECT #:THESE DRAWINGS AND SPECIFICATIONS ARECONFIDENTIAL AND SHALL REMAIN THE SOLEPROPERTY OF STARBUCKS CORPORATION,WHICH IS THE OWNER OF THE COPYRIGHT INTHIS WORK. THEY SHALL NOT BEREPRODUCED (IN WHOLE OR IN PART), SHAREDWITH THIRD PARTIES OR USED IN ANY MANNERON OTHER PROJECTS OR EXTENSIONS TO THISPROJECT WITHOUT THE PRIOR WRITTENCONSENT OF STARBUCKS CORPORATION.THESE DRAWINGS AND SPECIFICATIONS AREINTENDED TO EXPRESS DESIGN INTENT FOR APROTOTYPICAL STARBUCKS STORE (WHICH ISSUBJECT TO CHANGE AT ANYTIME) AND DONOT REFLECT ACTUAL SITE CONDITIONS.NEITHER PARTY SHALL HAVE ANY OBLIGATIONNOR LIABILITY TO THE OTHER (EXCEPT STATEDABOVE) UNTIL A WRITTEN AGREEMENT ISFULLY EXECUTED BY BOTH PARTIES.mcg architecture8/30/2017 5:43:37 PMJ:\2016 Projects\0-Starbucks\16514_SBX-6970_El Dorado & Fremont_Stockton_CA (NS-RELO)\02-Arch\3-CD\1-Revit Files\16514_SBX-6970_El Dorado & Fremont_Stockton.rvtG-001321295-04208/18/17ELDORADO &FREMONT510NELDORADOSTREETSTOCKTON, CA 95202SANJOAQUIN COUNTYCORE6970CH. LINM. DARMOKOOUTLINESPECIFICATIONSC. LEEG. MONTALVO16514Revision ScheduleRev Date By Description
|