|
DOORS AND WINDOWS1.1 SUMMARYA. STANDARD HOLLOW METAL DOORS AND FRAMES.1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED. INCLUDECONSTRUCTION DETAILS, MATERIAL DESCRIPTIONS, CORE DESCRIPTIONS,FIRE-RESISTANCE RATING, TEMPERATURE-RISE RATINGS, AND FINISHES.B. SHOP DRAWINGS: INCLUDE THE FOLLOWING:1. ELEVATIONS OF EACH DOOR DESIGN.2. DETAILS OF DOORS, INCLUDING VERTICAL AND HORIZONTAL EDGE DETAILSAND METAL THICKNESSES.3. FRAME DETAILS FOR EACH FRAME TYPE, INCLUDING DIMENSIONED PROFILESAND METAL THICKNESSES.4. LOCATIONS OF REINFORCEMENT AND PREPARATIONS FOR HARDWARE.5. DETAILS OF EACH DIFFERENT WALL OPENING CONDITION.6. DETAILS OF ANCHORAGES, JOINTS, FIELD SPLICES, AND CONNECTIONS.7. DETAILS OF ACCESSORIES.8. DETAILS OF MOLDINGS, REMOVABLE STOPS, AND GLAZING.9. DETAILS OF CONDUIT AND PREPARATIONS FOR POWER, SIGNAL, AND CONTROLSYSTEMS.1.3 INTERIOR FRAMESA. STANDARD-DUTY FRAMES: SDI A250.8, LEVEL 1. AT LOCATIONS INDICATED INTHE DOOR AND FRAME SCHEDULE.1. PHYSICAL PERFORMANCE: LEVEL C ACCORDING TO SDI A250.4.2. FRAMES:a. MATERIALS: UNCOATED, COLD-ROLLED STEEL SHEET, MINIMUMTHICKNESS OF 0.042 INCH (1.0 MM).b. CONSTRUCTION: KNOCKED DOWN.1.4 EXTERIOR HOLLOW-METAL DOORS AND FRAMESA. HEAVY-DUTY DOORS AND FRAMES: SDI A250.8, LEVEL 2. AT LOCATIONSINDICATED IN THE DOOR AND FRAME SCHEDULE.1. PHYSICAL PERFORMANCE: LEVEL B ACCORDING TO SDI A250.4, UL 752LEVEL 2 BULLET RESISTANT.2. DOORS:a. TYPE: AS INDICATED IN THE DOOR AND FRAME SCHEDULE.b. THICKNESS: 1-3/4 INCHES (44.5 MM.)c. FACE: METALLIC-COATED STEEL SHEET, WITH MINIMUM A40 (ZF120)COATING.d. EDGE CONSTRUCTION: MODEL 1, FULL FLUSH.e. CORE: MANUFACTURER'S STANDARD KRAFT-PAPER HONEYCOMB,POLYSTYRENE, POLYURETHANE, POLYISOCYANURATE, MINERAL-BOARD,OR VERTICAL STEEL-STIFFENER CORE AT MANUFACTURER'S DISCRETION.3. FRAMES:a. MATERIALS: METALLIC-COATED STEEL SHEET, MINIMUM THICKNESS OF0.053 INCH (1.3 MM), WITH MINIMUM A40 (ZF120) COATING.B. FINISHES:[FACTORY PRIMING FOR FIELD PAINTING] [FACTORY-APPLIED PAINT].1.5 INSTALLATIONA. METAL-STUD PARTITIONS AND CONCRETE WALLS: FRAMES FILLED WITHINSULATION.B. MASONRY WALLS: FRAMES FILLED WITH GROUT.END OF SECTION 081130SECTION 081130 – HOLLOW METAL DOORS AND FRAMESDOORS AND WINDOWS1.1 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF DOOR INDICATED. INCLUDE DETAILS OFCORE AND EDGE CONSTRUCTION AND TRIM FOR OPENINGS.B. SHOP DRAWINGS: INDICATE LOCATION, SIZE, AND HAND OF EACH DOOR;ELEVATION OF EACH KIND OF DOOR; CONSTRUCTION DETAILS NOT COVERED INPRODUCT DATA; LOCATION AND EXTENT OF HARDWARE BLOCKING; AND OTHERPERTINENT DATA.1. INDICATE DIMENSIONS AND LOCATIONS OF MORTISES AND HOLES FORHARDWARE.2. INDICATE DIMENSIONS AND LOCATIONS OF CUTOUTS.3. INDICATE REQUIREMENTS FOR VENEER MATCHING.4. INDICATE DOORS TO BE FACTORY FINISHED AND FINISH REQUIREMENTS.5. INDICATE FIRE-PROTECTION RATINGS FOR FIRE-RATED DOORS.C. WARRANTY: SAMPLE OF SPECIAL WARRANTY.1.2 QUALITY ASSURANCEA. QUALITY STANDARD: AWI.1. AWI QUALITY CERTIFICATION LABELS OR AN AWI LETTER OF LICENSING FORDOORS.2. WI-CERTIFIED COMPLIANCE CERTIFICATE FOR DOORS AND INSTALLATION.B. FIRE-RATED WOOD DOORS: POSITIVE PRESSURE TESTING.1.3 DOOR CONSTRUCTION, GENERALA. LOW-EMITTING MATERIALS: MADE WITH ADHESIVES AND COMPOSITE WOODPRODUCTS THAT DO HAVE NO ADDED UREA FORMALDEHYDE.B. WDMA I.S.1-A PERFORMANCE GRADE: HEAVY DUTY UNLESS OTHERWISE INDICATED.1.4 VENEERED-FACED DOORS FOR TRANSPARENT FINISHA. INTERIOR SOLID-CORE DOORS:1. CORE: PARTICLEBOARD.2. CONSTRUCTION: FIVE OR SEVEN PLIES, BONDED.1.5 PRIMING/FINISHINGA. SHOP PRIMING:1. DOORS FOR OPAQUE FINISH: ONE COAT OF WOOD PRIMER.2. DOORS FOR TRANSPARENT FINISH: STAIN AND FIRST COAT OF FINISH.B. FACTORY FINISHING: ALL DOORS.END OF SECTION 081416SECTION 081416 - FLUSH WOOD DOORSDOORS AND WINDOWS1.1 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE AND SIZE OF OVERHEAD COILING DOOR ANDACCESSORY. INCLUDE THE FOLLOWING:B. SHOP DRAWINGS: FOR EACH INSTALLATION AND FOR SPECIAL COMPONENTS NOTDIMENSIONED OR DETAILED IN MANUFACTURER'S PRODUCT DATA. INCLUDEPLANS, ELEVATIONS, SECTIONS, DETAILS, AND ATTACHMENTS TO OTHER WORK.1. DETAIL EQUIPMENT ASSEMBLIES AND INDICATE DIMENSIONS, WEIGHTS, LOADS,REQUIRED CLEARANCES, METHOD OF FIELD ASSEMBLY, COMPONENTS, ANDLOCATION AND SIZE OF EACH FIELD CONNECTION.C. SAMPLES FOR INITIAL SELECTION: MANUFACTURER'S FINISH CHARTS SHOWINGFULL RANGE OF COLORS AND TEXTURES AVAILABLE FOR UNITS WITH FACTORY-APPLIED FINISHES.1. INCLUDE SIMILAR SAMPLES OF ACCESSORIES INVOLVING COLOR SELECTION.D. SAMPLES FOR VERIFICATION: FOR EACH TYPE OF EXPOSED FINISH REQUIRED,PREPARED ON SAMPLES OF SIZE INDICATED BELOW.1. CURTAIN SLATS: 12 INCHES(305 MM) LONG.2. BOTTOM BAR: 6 INCHES(150 MM) LONG.3. GUIDES: 6 INCHES(150 MM) LONG.4. BRACKETS: 6 INCHES(150 MM) SQUARE.5. HOOD: 6 INCHES(150 MM) SQUARE.E. QUALIFICATION DATA: FOR QUALIFIED INSTALLER.F.[SEISMIC QUALIFICATION CERTIFICATES: FOR OVERHEAD COILING DOORS,ACCESSORIES, AND COMPONENTS, FROM MANUFACTURER.]G. MAINTENANCE DATA: FOR OVERHEAD COILING DOORS TO INCLUDE INMAINTENANCE MANUALS.1.2 PERFORMANCE REQUIREMENTSA. OPERATION-CYCLE REQUIREMENTS: PROVIDE OVERHEAD COILING GRILLECOMPONENTS AND OPERATORS CAPABLE OF OPERATING FOR NOT LESS THAN50,000 CYCLES AND FOR 25 CYCLES PER DAY.1.3 DOOR ASSEMBLYA. GENERAL: FABRICATE OVERHEAD COILING GRILLE CURTAIN CONSISTING OF ANETWORK OF 5/16-INCH-(8-MM-) MINIMUM DIAMETER HORIZONTAL RODS, OR RODSCOVERED WITH TUBE SPACERS, SPACED AS INDICATED. INTERCONNECT RODS BYVERTICAL LINKS APPROXIMATELY 5/8 INCH(16 MM) WIDE, SPACED AS INDICATED ANDROTATING ON RODS.1. SPACE RODS AT APPROXIMATELY 1-1/2 INCHES(38 MM) O.C.2. SPACE LINKS APPROXIMATELY 9 INCHES(228 MM) APART IN ASTRAIGHT IN-LINE PATTERN.3. ALUMINUM GRILLE CURTAIN: ASTM B 221(ASTM B 221M), ALLOY ANDTEMPER RECOMMENDED BY ALUMINUM PRODUCER AND FINISHER FOR TYPE OFUSE AND FINISH INDICATED.B. HOOD: ALUMINUM.C. MANUAL DOOR OPERATOR.1.4 INSTALLATIONA. FACTORY-AUTHORIZED REPRESENTATIVE TO[PERFORM STARTUP SERVICE ANDTESTING] [AND] [TRAIN OWNER'S PERSONNEL].END OF SECTION 083326SECTION 083326 - OVERHEAD COILING DOORSDOORS AND WINDOWSPART 1 - GENERAL1.1 SUMMARYA. SECTION INCLUDES:1. SOLID-CORE DOUBLE ACTING SWING DOORS WITH PLASTIC LAMINATE FACES.1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED. INCLUDECONSTRUCTION DETAILS, MATERIAL DESCRIPTIONS, CORE DESCRIPTIONS, FIRE-RESISTANCE RATING, TEMPERATURE-RISE RATINGS, AND FINISHES.B. SHOP DRAWINGS: INCLUDE THE FOLLOWING:1. ELEVATIONS OF EACH DOOR DESIGN.2. DETAILS OF DOORS, INCLUDING VERTICAL AND HORIZONTAL EDGE DETAILS ANDMETAL THICKNESSES.3. FRAME DETAILS FOR EACH FRAME TYPE, INCLUDING DIMENSIONED PROFILESAND METAL THICKNESSES.4. LOCATIONS OF REINFORCEMENT AND PREPARATIONS FOR HARDWARE.5. DETAILS OF ACCESSORIES.6. DETAILS OF MOLDINGS, REMOVABLE STOPS, AND GLAZING.1.3 STANDARD DOUBLE ACTING SWING DOORSA. GENERAL: PROVIDE DOORS OF DESIGN INDICATED, NOT LESS THAN THICKNESSINDICATED; FABRICATED WITH SMOOTH SURFACES, WITHOUT VISIBLE JOINTS ORSEAMS ON EXPOSED FACES UNLESS OTHERWISE INDICATED. COMPLY WITHANSI/SDI A250.8.1. DESIGN: AS INDICATED.B. CORE CONSTRUCTION: 3/4” EXTERIOR GRADE SOLID WOOD CORE MADE WITHADHESIVES AND COMPOSITE WOOD PRODUCTS THAT DO NOT CONTAIN UREAFORMALDEHYDE.1. VERTICAL EDGES FOR DOUBLE-ACTING DOORS: ROUND VERTICAL EDGES WITH2-1/8-INCH(54-MM) RADIUS.2. TOP AND BOTTOM EDGES: CLOSED WITH FLUSH OR INVERTED 0.042-INCH-(1.0-MM-)THICK, END CLOSURES OR CHANNELS OF SAME MATERIAL AS FACE SHEETS.3. TOLERANCES: COMPLY WITH SDI 117, "MANUFACTURING TOLERANCES FORSTANDARD STEEL DOORS AND FRAMES."C. INTERIOR DOORS: FACE SHEETS FABRICATED FROM DECORATIVE HIGH PRESSURELAMINATE. PROVIDE DOORS COMPLYING WITH REQUIREMENTS INDICATED BELOWBY REFERENCING ANSI/SDI A250.8 FOR LEVEL AND MODEL AND ANSI/SDI A250.4 FORPHYSICAL PERFORMANCE LEVEL:1. LEVEL 1 AND PHYSICAL PERFORMANCE LEVEL C (STANDARD DUTY).a. WIDTH: AS INDICATED ON DRAWINGS.D. HARDWARE REINFORCEMENT: FABRICATE ACCORDING TO ANSI/SDI A250.6 WITHREINFORCING PLATES OF 18 GAUGE STAINLESS STEEL.E. FABRICATE CONCEALED STIFFENERS AND HARDWARE REINFORCEMENT FROMEITHER COLD- OR HOT-ROLLED STEEL SHEET.1.4 STOPS AND MOLDINGSA. MOLDINGS FOR GLAZED LITES IN DOORS: MINIMUM 0.032 INCH(0.8 MM) THICK.B. LOOSE STOPS FOR GLAZED LITES IN FRAMES: MINIMUM 0.032 INCH(0.8 MM) THICK,FABRICATED FROM SAME MATERIAL AS FRAMES IN WHICH THEY ARE INSTALLED.1.5 STEEL FINISHESA. PRIME FINISH: APPLY MANUFACTURER'S STANDARD PRIMER IMMEDIATELY AFTERCLEANING AND PRETREATING.1. SHOP PRIMER: MANUFACTURER'S STANDARD, FAST-CURING, LEAD- ANDCHROMATE-FREE PRIMER COMPLYING WITH ANSI/SDI A250.10 ACCEPTANCECRITERIA; RECOMMENDED BY PRIMER MANUFACTURER FOR SUBSTRATE;COMPATIBLE WITH SUBSTRATE AND FIELD-APPLIED COATINGS DESPITEPROLONGED EXPOSURE.B. FACTORY-APPLIED PAINT FINISH: MANUFACTURER'S STANDARD, COMPLYING WITHANSI/SDI A250.3 FOR PERFORMANCE AND ACCEPTANCE CRITERIA.1.6 COLOR AND GLOSS: AS INDICATED BY MANUFACTURER'S DESIGNATIONS.END OF SECTION 083450SECTION 083450 - DOUBLE ACTING SWING DOORSDOORS AND WINDOWS1.1 PERFORMANCE REQUIREMENTSA. DELEGATED DESIGN: CONTRACTOR TO DESIGN ALUMINUM-FRAMED SYSTEMS.B. DEFLECTION OF FRAMING MEMBERS:1. DEFLECTION NORMAL TO WALL PLANE: LIMITED TO L/175.2. DEFLECTION PARALLEL TO GLAZING PLANE: LIMITED TO L/360 OR 1/8 INCH(3.2 MM), WHICHEVER IS SMALLER.C. AIR INFILTRATION:1. FIXED FRAMING AND GLASS AREA: MAXIMUM AIR LEAKAGE OF 0.06 CFM/SQ.FT. (0.30 L/S PER SQ. M) AT A STATIC-AIR-PRESSURE DIFFERENTIAL OF 1.57LBF/SQ. FT. (75 PA).2. ENTRANCE DOORS:a. PAIR OF DOORS: MAXIMUM AIR LEAKAGE OF 1.0 CFM/SQ. FT. (5.08 L/S PERSQ. M) AT A STATIC-AIR-PRESSURE DIFFERENTIAL OF 1.57 LBF/SQ. FT. (75 PA).b. SINGLE DOORS: MAXIMUM AIR LEAKAGE OF 0.5 CFM/SQ. FT. (2.54 L/S PERSQ. M) AT A STATIC-AIR-PRESSURE DIFFERENTIAL OF 1.57 LBF/SQ. FT. (75 PA).1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH TYPE OF PRODUCT.B. SHOP DRAWINGS: INCLUDE PLANS, ELEVATIONS, SECTIONS, FULL-SIZE DETAILS,AND ATTACHMENTS TO OTHER WORK.1. SHOW CONNECTION TO AND CONTINUITY WITH ADJACENT THERMAL,WEATHER, AIR, AND VAPOR BARRIERS.C. SAMPLES: FOR EACH EXPOSED FINISH REQUIRED.D. ENERGY PERFORMANCE CERTIFICATES.1.3 MATERIALSA. ALUMINUM: ALLOY AND TEMPER RECOMMENDED BY MANUFACTURER.B. STEEL REINFORCEMENT.1.4 SYSTEM COMPONENTSA. FRAMING MEMBERS:1. CONSTRUCTION: THERMALLY BROKEN.2. GLAZING SYSTEM: GASKETS ON FOUR SIDES.3. GLAZING PLANE: FRONT.B. GLAZING: SECTION 088000 "GLAZING."C. ENTRANCE DOORS:1. DOOR CONSTRUCTION: 1-3/4-INCH (44.5-MM) OVERALL THICKNESS.2. DOOR DESIGN: AS INDICATED.D. ENTRANCE DOOR HARDWARE: AS SCHEDULED.END OF SECTION 084113SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTSDOORS AND WINDOWS1.1 SUMMARYA. COMMERCIAL DOOR HARDWARE FOR SWINGING DOORS.B. OTHER DOORS TO THE EXTENT INDICATED.C. CYLINDERS FOR DOORS SPECIFIED IN OTHER SECTIONS.1.2 SUBMITTALSA. PRODUCT DATA: INCLUDE CONSTRUCTION AND INSTALLATION DETAILS, MATERIALDESCRIPTIONS, DIMENSIONS OF INDIVIDUAL COMPONENTS AND PROFILES, ANDFINISHES.1.3 WARRANTYA. WARRANTY PERIOD: ONE YEAR FROM DATE OF SUBSTANTIAL COMPLETION,EXCEPT AS FOLLOWS:1. MANUAL CLOSERS: 25 YEARS FROM DATE OF INVOICE.2. CYLINDRICAL LOCKSETS: TWO YEARS FROM DATE OF INVOICE.3. EXIT DEVICES: FIVE YEARS FROM DATE OF INVOICE.1.4 MAINTENANCE SERVICEA. FULL-MAINTENANCE SERVICE: SIX MONTHS.1.5 PRODUCTSA. CYLINDERS AND KEYING:1. CONSTRUCTION KEYING: CONSTRUCTION[MASTER KEYS] [CORES].2. KEYING SYSTEM:a. GRAND MASTER KEY.b. LOCKS MASTER KEYED OR GRAND MASTER KEYED TO EXISTING SYSTEM.c. ALL CYLINDERS KEYED ALIKE.d. KEYS: NICKEL SILVER.1) STAMPING: PERMANENTLY INSCRIBE EACH KEY WITH A LOCKNET KEYCONTROL NUMBER, STATE CODE, AND INCLUDE THE FOLLOWINGNOTATION:a) NOTATION: "DO NOT DUPLICATE."2) QUANTITY: IN ADDITION TO ONE EXTRA KEY BLANK FOR EACH LOCK,PROVIDE THE FOLLOWING:a) CYLINDER CHANGE KEYS: TWO.b) CONSTRUCTION KEYS: FOUR.c) MASTER KEYS: FOUR.d) GRAND MASTER KEYS: TWO.1.6 FIELD QUALITY CONTROLA. INDEPENDENT ARCHITECTURAL HARDWARE CONSULTANT:[OWNER][CONTRACTOR]ENGAGED TO PERFORM INSPECTIONS.B. OCCUPANCY ADJUSTMENT: THREE MONTHS.END OF SECTION 087100SECTION 087100 - DOOR HARDWAREDOORS AND WINDOWS1.1 SUMMARYA. GLASS FOR WINDOWS, DOORS AND STOREFRONT FRAMING.1.2 SUBMITTALSA. PRODUCT DATA: FOR EACH PRODUCT.B. PRODUCT CERTIFICATES: FOR GLASS.1.3 MATERIALSA. SILICONE GLAZING SEALANTS:[NEUTRAL] [NEUTRAL OR BASIC] [ACID]CURING,CLASS[25] [50] [100/50], VOC LESS THAN 250 G/L.B. GLAZING TAPES:[BACK-BEDDING-MASTIC] [EXPANDED-CELLULAR]TYPE.C. GLAZING GASKETS:[DENSE COMPRESSION] [SOFT COMPRESSION] [LOCK STRIP].1.4 MONOLITHIC GLASS SCHEDULEA. GLASS TYPE[GL-<#>]: LOW-E-COATED, CLEAR INSULATING GLASS.1. OUTDOOR LITE: ANNEALED FLOAT GLASS.2. INDOOR LITE: ANNEALED FLOAT GLASS.B. GLASS TYPE[GL-<#>]: LOW-E-COATED, CLEAR INSULATING GLASS.1. OUTDOOR LITE: FULLY TEMPERED FLOAT GLASS.2. INDOOR LITE: FULLY TEMPERED FLOAT GLASS.END OF SECTION 088000SECTION 088000 - GLAZING2401 UTAH AVENUE SOUTHSEATTLE, WASHINGTON 98134(206) 318-1575SHEET NUMBER:SHEET TITLE:SCALE: AS SHOWNSTORE #:PROFILE TYPE:PROJECT #:ISSUE DATE:PROGRAM MANAGER:STORE DESIGNER:CHECKED BY:PROJECT NAME:PROJECT ADDRESS:STARBUCKS COFFEECOMPANYRLEED AP:© 2017 STARBUCKS COFFEE COMPANY®111 Pacifica, Suite 280, Irvine, CA 92618P: 949.553.1117 F: 949.474.7056San FranciscoClevelandDenverIrvineARCHITECT OF RECORDARCHITECT STAMP2017MCG PROJ. MANAGER:MCG PROJ. SPECIALIST:MCG PROJECT #:THESE DRAWINGS AND SPECIFICATIONS ARECONFIDENTIAL AND SHALL REMAIN THE SOLEPROPERTY OF STARBUCKS CORPORATION,WHICH IS THE OWNER OF THE COPYRIGHT INTHIS WORK. THEY SHALL NOT BEREPRODUCED (IN WHOLE OR IN PART), SHAREDWITH THIRD PARTIES OR USED IN ANY MANNERON OTHER PROJECTS OR EXTENSIONS TO THISPROJECT WITHOUT THE PRIOR WRITTENCONSENT OF STARBUCKS CORPORATION.THESE DRAWINGS AND SPECIFICATIONS AREINTENDED TO EXPRESS DESIGN INTENT FOR APROTOTYPICAL STARBUCKS STORE (WHICH ISSUBJECT TO CHANGE AT ANYTIME) AND DONOT REFLECT ACTUAL SITE CONDITIONS.NEITHER PARTY SHALL HAVE ANY OBLIGATIONNOR LIABILITY TO THE OTHER (EXCEPT STATEDABOVE) UNTIL A WRITTEN AGREEMENT ISFULLY EXECUTED BY BOTH PARTIES.mcg architecture8/30/2017 5:43:32 PMJ:\2016 Projects\0-Starbucks\16514_SBX-6970_El Dorado & Fremont_Stockton_CA (NS-RELO)\02-Arch\3-CD\1-Revit Files\16514_SBX-6970_El Dorado & Fremont_Stockton.rvtG-001221295-04208/18/17ELDORADO &FREMONT510NELDORADOSTREETSTOCKTON, CA 95202SANJOAQUIN COUNTYCORE6970CH. LINM. DARMOKOOUTLINESPECIFICATIONSC. LEEG. MONTALVO16514Revision ScheduleRev Date By Description
|