Laserfiche WebLink
TEE 3• x r x r AV TEE r X 3-X 3'ASM <br /> CA 3!751 5359115 I1-31711)535" <br /> PLUG.3'PIC Mi 40 - - - T PLUG 3'PVC SCR 40 <br /> l r PVC NILE AOAP03t t REUMRW IF <br /> 3'PVC SCII 10 PIPE W SFE TAMC P17TAIr�IS THREMED) <br /> DO lar 9TLOW%LD ANP WE � yA PP ams ffm i 7A6Y Ftt71Wc tint BE 7xR3� <br /> ASMHLV Jw 12 RACE in- rLK6 I"lWmrmrL M SOCW aNCUIRU <br /> ULJw"tWm170pt"t mn= <br /> am man TAW nu <br /> ATUD40 um cum ayes SMACE <br /> I a NAYS tam MY IF <br /> ulawt n nm o Fr W <br /> 0 <br /> 3'PVC WILE AOAPMR(RECUBW W <br /> TtE TANK F3TrM IS THREMM) <br /> W <br /> MW V <br /> 3•PVC Xi 41)PTFE <br /> SEH. 10 PVC Ptd FllAa® <br /> 7 0 BF so I F t®N�r1P ta�i0 °:alE°a 3 FnE <br /> 9m <br /> l 9rP11Nr aA i <br /> T"nr W PZPE 4 00 <br /> sAe <br /> � al ca i I � [tA CLAW <br /> ! am 1r) WN(3* 0.1p(r) <br /> i <br /> ) i <br /> 9MZKCU <br /> ELAW t ; <br /> 07" CLAW <br /> rrP Cr) (DAM <br /> 1 CAP Cr) <br /> 1 Q->zlx� I <br /> Frrrzm <br /> 3is74�1 1e I <br /> (I-=72)AGMU7 ATrACHES Ta nN <br /> MTEWk PVC wLL04%e ncwi ON MH THE 3011r R FAM <br /> 324MTSN1 SRO i PONIMI <br /> l AT7ACiEO 7Waa6R PP'R i <br /> XAVW aAPN'CS)AND <br /> PE FIM nu IPA=AT <br /> 19']NTMAU C891id1 <br /> cALmNArTva I>S31 <br /> CIli70WtEN>3t8W <br /> PIPE NAT SN3 RPR A C>11FLEN AND ALDn"MOl_ <br /> Ftl�lfl PF�IItE 711E 5�181IFE0 L6bIH <br /> PIPE 54Y A tI;PLEQ AMADFII7]]HAL <br /> PIPE 70 PROMIIk BE SZPSHR®LENM <br /> Figure 4 7 <br /> 48 ULTRASONIC LEVEL INDICATOR <br /> 481 Install the PE bulkhead fitting per section 3 1 for sensors with male pipe threads Install the sensor <br /> into the fitting with Teflon*pipe sealant Remove the display unit box cover Attach the display unit to <br /> the PE mounting plates provided on the tank with 4 ea #10 S S Self-tapping screws Attach the <br /> sensor cable to the control box with small strain relief and connect wires per label in the box Attach <br /> the unit to 110 VAC and test unit The display unit is preprogrammed for the tank ordered The <br /> display with show hundreds of gallons(display x 100=gallons) Refer to itturature shipped with unit to <br /> answer any-additional questions <br /> 49 LEAK DETECTOR UNIT(FOR USE WITH CAPTOR CONTAINMENT TANKS ONLY) <br /> 491 The leak detector unit consists of a proximity sensor,2 in FPT fitting connection,2 in bung plug, <br /> 3/4 in strain relief, and an indicator box Install the 3Y4 in strain relief into the 2 in bung plug Loosely <br /> Install the proximity sensor cord into the strain relief with the sensor face to the inside of the plug <br /> assembly Place the sensor in the interstitial space between the primary and secondary tanks <br /> approximately 1 in above the tank bottom and securely tighten the strain relief to hold the sensor and <br /> 16 <br />