Laserfiche WebLink
• NOTE This ladder is provided for tank Inspection only At no time should the operator <br /> step off this ladder onto the tank unless stepping onto an approved work platform with <br /> guard rails or utilizing some other approved safety device Proper safety equipment (i e <br /> guard rads,safety harness, etc) must be used to step onto the tank Consult applicable <br /> regulations to determine proper safety equipment <br /> 562 Attach the stainless steel top pivoting attachment arms to the ladder using the 112" bolt and 3/4" <br /> bushing assemblies (2 required) as shown in Figure 5 6. Position the ladder on the tank and <br /> attach the top pivoting attachment arms to the tank with the ladder attachment tube and cotter <br /> keys provided (see assembly drawing) Position the ladder parallel with the side of the tank and <br /> mark 4 ea 5/e"anchor bolt locations. Install appropriate 518°anchor bolts and attach the bottom <br /> of the ladder to the concrete pad. Anchor bolts are not provided by the manufacturer and must be <br /> purchased by the customer <br /> TANG UMTMX PA <br /> 2000 X lD 9757011 140 e 00 <br /> 2500 R In SO= 310 0 1050 111 <br /> 3000 R m SUM 101 a t22 0 Ile <br /> ]000 R 1@ 71 W177 a M a t11 <br /> 300o X W ON Zug 15B a <br /> 44M X 00 57100 2140 771.0 Ito <br /> 4sm c 102 IMM90MI 104 0 17e 0 W <br /> a000 x m 206 tst7 0 io <br /> SSW X m 7M= 2S1 0 210 0 <br /> 8 5500 x t20 7tmOR HIDO 1200 ,M <br /> pRUfTIFIG SM x 142 X57001 1210 07 a <br /> �"ME Kr awa z lag 74I0001 m o 163 a w <br /> ai590 x 120 Alam SAA 0 110 e va <br /> 7=x to M7 a 100. <br /> 7500 L"'t 74{00 2M a fiAi.O <br /> Q050 X 531700[ 170 0 1No <br /> 10500 X t MM= 103 0 in 9 00 <br /> 12500 z tit o tet a <br /> 19000 X l0 27R 0 717 O <br /> FRP lADOEL �l A 1�'O B TNR DREMIMBETWEEN <br /> A J" <br /> AN1i BMT SPACER TIS 7RI BE PLACED�TMC�3f T1E 1 <br /> 1�13 7N0:E,l[®t LIG AIA THE Cni'ffR PIN teirA <br /> G1 PQSITI01 PMTIAG THE AO/IB![JIIM <br /> PIY M ATTAl HMM AN <br /> FMP UnDIR <br /> REINFUIMMEK <br /> CHKKMEL <br /> LADDER <br /> ATTA[M@IT <br /> TII� <br /> LUM ATTU MOIT 1113E <br /> TNR S I Irs <br /> TANK LADDER ATT OMW 1116 <br /> PI40TIW ATTALIIIBR AAM <br /> F-- -- — -� FRP LAMM IIRIG <br /> l Vr-i3 X 3-t/r MLT <br /> l 11r FLAP WASHER <br /> l M LAMB 9ARL <br /> l VY FLAT WASHER <br /> L 3N•asam <br /> l l FOYOTTKi ATTAf H?M ARM <br /> l <br /> l <br /> l 14'RAT YASM <br /> Y}Fy A•A(LE"SIM ML7) I �'-t3 N71 L=Ow <br /> 3/18 X Y mT1E!PINS <br /> Figure 5 6 <br /> 57 FRP LADDER CAGES <br /> 571 Using the assembly drawing shown in Figure 5 7 and the instructions in section 5 7 2, verify that <br /> the correct number of fasteners have been shipped to attach the FRP cage unit These cages are <br /> designed for use only with the Sit FRP ladder design Cages are required for ladders used to <br /> ascend to heights exceeding 20 ft <br /> NOTE Assembly is easier of the cage unit is installed on the ladder before ladder installation <br /> • <br /> 24 <br />