COMPLIANCE INFO - Laserfiche WebLink

Home Browse Search

SPECIAL PRECAUTIONS FOR HANDLING GAS CYLINDERS (Continued): Cylinders should be stored upright and be firmly secured to prevent falling or being knocked over. Cylinders can be stored in the open, but in such cases, should be protected against extremes of weather and from the dampness of the ground to prevent rusting. Never tamper with pressure relief devices in valves and cylinders. Liquefied Carbon Dioxide must be stored and handled under positive pressure or in a closed system to prevent the infiltration and solidification of air or other gases. The following rules are applicable to situations in which cylinders are being used: Before Use: Move cylinders with a suitable hand -truck. Do not drag, slide or roll cylinders. Do not drop cylinders or permit them to strike each other. Secure cylinders firmly. Leave the valve protection cap in-place (where provided) until cylinder is ready for use. During Use: Use designated CGA fittings and other support equipment. Do not use adapters. Do not heat cylinder by any means to increase the discharge rate of the product from the cylinder. Use check valve or trap in discharge line to prevent hazardous backflow into the cylinder. Do not use oils or grease on gas -handling fittings or equipment. *Jterf--Crose main cylinder valve. Replace valve protection cap (where provided). Mark empty cylinders "EMPTY°,. NOTE: Use only DOT or ASME code containers. In the event of an electrical discharge, Carbon Dioxide gas will produce carbon monoxide and oxygen. Close valve after each use and when empty. Cylinders must not be recharged except by or with the consent of owner. SPECIAL PRECAUTIONS FOR HANDLING PRESSURIZED CONTAINERS OF LIQUID CARBON DIOXIDE: Cold liquids can present significant safety hazards. Never allow any unprotected part of the body to touch uninsulated pipes or vessels which contain cold fluids. The extremely cold metal of the container will cause moist flesh to stick fast and tear when one attempts to withdraw from it. The following rules are applicable to work situations in which liquid containers are being used. Check all hoses and transfer equipment before filing them with the liquid. Replace any worn or cut hoses prior to use. Liquid Carbon Dioxide is extremely cold and is under pressure. A leak will result in the formation of "Dry Ice" particles which will be forcibly ejected from the system, possibly injuring the operator. A complete hose failure can result in a large release of Carbon Dioxide and violent movement of the hose and associated equipment, which may cause severe injury or death. Special care must be taken when depressurizing and disconnecting hoses. Releasing the contents of a liquid - filled line to atmospheric pressure may result in the formation of a solid dry ice plug in the line. This plug will prevent further removal of the liquid behind the plug, resulting in either an unexpected, rapid release of Carbon Dioxide as the line warms, or the catastrophic failure of the line as the liquid warms behind the plug. Sufficient vapor pressure must be applied and maintained behind the liquid before opening a discharge valve. This action will prevent the depressurization of the liquid to the point of solid formation before it exits the line. High-pressure containers for liquid product are equipped with pressure relief devices to control internal pressure. Under normal conditions, these containers will periodically vent small amounts of product. Some metals such as carbon steel may become brittle at low temperatures and will easily fracture. Prevent entrapment of liquid in closed systems or piping without pressure relief devices. SPECIAL PRECAUTIONS FOR HANDLING OF SOLID CARBON DIOXIDE: Do not handle solid Carbon Dioxide with bare hands. Use heavy gloves or dry ice tongs. Handle blocks of dry ice carefully, as injuries can occur if one is accidentally dropped on the feet. Never store dry ice in a standard refrigerator, cooler, or freezer designed for food storage. Containers of solid Carbon Dioxide should be stored upright and be firmly secured to prevent falling or being knocked -over. Containers should be vented, to prevent the build-up of Carbon Dioxide gas. Carbon Dioxide sublimates at -78.5°C (-109.30F); containers should be thermally insulated and kept at the lowest possible temperature to maintain the solid and avoid generation of Carbon Dioxide gas. Storage containers and equipment used with Carbon Dioxide should not be located in sub -surface or enclosed areas, unless engineered to maintain a concentration of Carbon dioxide below the TLV (TLV = 5000 ppm in the event of a release. Solid consignment of dry ice in a gas-tight vessel can lead to catastrophic failure of the vessel by over -pressurization. Storage of dry ice should never occur in a gas-tight container. PROTECTIVE PRACTICES DURING MAINTENANCE OF CONTAMINATED EQUIPMENT: Follow practices indicated in Section 6 (Accidental Release Measures). Make certain application equipment is locked and tagged -out safely. Purge gas handling equipment with inert gas (e.g., Nitrogen) before attempting repairs. PARRnN nlnYln= - rn_ RACnCZmnrm11kAr rr*nninvm