INSTALL_2009 - Laserfiche WebLink

Home Browse Search

Bonded Double-Wall Sump Entry/Termination Fitting 5. Place one ring over the sump fit- 9. Slide the metal retaining ring over excess adhesive from all bonding sur- ting in the inside of the sump and rotate inside section of sump fitting against faces. See adhesive kit instructions for to the desired angle. Make alignment the alignment rings until they are tight cure times. mark on both the sump wall and the against sump wall. (A short section of 11. The use of an industrial hot air gun ring. 4" pipe may be used to drive the metal may speed up the curing process. Do 6. Mix one 7014 or 8014 adhesive for retaining ring over the fitting.) Be sure not overheat. each fitting per the instructions in the there is an adhesive bead visible 12. Remove '/4" plastic threaded out- adhesive kit. Mix in filler to thicken between the rings and the sump wall. let protector. Apply adhesive to the '/4" adhesive(fiberglass alignment rings The metal ring must hold the assembly fitting and screw into the '/." threaded will not seal properly without filler). in position while the adhesive cures. If outlet. Tighten to 40 in.-lbs. or 11/2-2 7. Apply adhesive generously, appro- the assembly is not tight against the turns past hand tight. After installing ximately'/16"thick to the inside and sump wall, firmly press the entry fitting fitting, be sure the interstitial space is the outside of the sump walls where against the outside sump wall while free from excess adhesive. Install a the alignment rings are located. Coat pressing the metal ring against the short hose and blow excess adhesive cut edges of the entry hole. Apply a alignment ring on the inside. through the air passage. thin coating of adhesive to the bonding 10. Do not disturb assembly until the 13. Connect only flexible tubing or hos- surfaces of the alignment rings. adhesive is cured. This includes bond- es to the '/4"side outlet. 8. Line up rings with alignment marks ing of pipe to the entry fitting and install- NOTE: Tubing or hoses must be rated and press together firmly. ing the threaded outlet fitting. Clean to full vacuum. TERMINATION EXAMPLE using SUMP E NTRYrFERMI NATION FfTTINGS Pdmary poo Spigot z NPT adapter w Red Thread IIA Spigot r Spigot Nipple Conccnuic Reducer O v'tm.e•rD•4eps. I • The 11V threads are a'"caddied NPT"-ttv insu uon of a standard spec male dread Is minimized. • Sndm Fibemast 7014 or 8014 adhesire Is recommended Corr�mxra pipe • The 114"female threads are fiborglass and cams he tightened the Sump Entry/ Red Ttread IIA Tmmnation Fitting same as a mMaltic thread.Tgracn to 40 in46s or 1.52 roans • After instatling a 114"NPT rating,the passageway to the Use concentric reducer to connect the sump en /termination piping interstitial spare should be cleared with ar pressure to fitting to secondary containment pipe;DO NOT USE clamshell intoe mat d is free of dread sealant andtor adhesiw, termination fittings with this styte fitting. ItVs the`poticy of Fiber Gass Systems to iinprove'ts pradut is continually. In accordance wits fhat policy, j the right is reserved to make changes in specifications,descriptions,and illustrative material contained in this bulletin as conditions warrant. Always cross-reference the bulletin date with the most current version listed at http:/Avww.fgspipe.com. The information contained herein is general in nature and is not intended to express any warranty of any type whatsoever, nor shall any be implied. MEMBER ISO 9001 YEfg "ARINUIRA , 1:EQWWNTIN r FIBER GLASS SYSTEMS ®Trademark of Varco I/P,Inc_ FIBER GLASS SYSTEMS•A NATIONAL OILWELL VARCO COMPANY www.smithfibercast.com 2700 W_65th ST.,LITTLE ROCK,AR 72209•501-568-4010•FAX 501-568-4465 Printed U_S.A. 1M1007 25 S.MAIN ST,SAND SPRINGS,OK 74063.918-245-6651 •FAX 918-245-7566