Laserfiche WebLink
CONTAINMENT CROSSOVER DLMIL SUMP CONNECTIONS <br /> When Installing a secondary containment system, some <br /> preparation is necessary if thea closest possible separation of Single Wali Sump Entry/Termination Fitting <br /> lines is required. To minimize the ovarall change in elevation (Refer to 82107 for installation Information) <br /> when installing a containment crossover, it Is necessary to sumpV-Wl <br /> shorten one leg of the 450 containment elbow and the side / Rc'ainiN Rirg <br /> A!_igymrntfL'nss Al�grinant Rings <br /> m'� / <br /> outlet run of the containment tee. E-Mry/Tenar n Fitting B \\ / <br /> Refer to Table 10 for the max?mum length that can be removed <br /> and for the minimum nipple length of both product piping and <br /> secondary containment piping. <br /> ou:5lge Sump C <br /> NOTE: Use Self-tapping screws or match drill two holes($/16") HCA 04-1 - inswe5 an7 <br /> at a distance of 3/4"(19 mm)from the out and of the 4.5' elbow <br /> and the tea. <br /> 1 <br /> TABLE 10. Containment Crossover information 1 e <br /> Containment Pipe Size <br /> 31' (max. 4" (max. 6" (Max. <br /> Fitting in.) <br /> RorviovQ from 45" 125 2.00 1.25 <br /> elbow <br /> Remove from side Double Wall Sump Entry/Termination Fitting <br /> 1.50 1.63 1.00 with Bonded Fiberglass Alignment Rings <br /> run of tee <br /> Product nipple size 2x8 3x8 4x'10 (Refer to B2108 for installation Information) <br /> Cl) <br /> E�ryRwiu5on Rtrrq c=q 9LL'M WA <br /> Containmentrtippte 3x6 4x6 6x8 "9AMWxR WW <br /> size <br /> (1)Actual length of the product nipple will vary slightly because t <br /> of different ineertion lengths due to variations of tapers. c�aea my <br /> To prevent Interference of the pipelines, do not locate two <br /> containment fittings closer than shown in Table 11 and the <br /> drawing below. ---- -- M54as nv <br /> TABLE 11. pipe Separation Distan000 ou oa <br /> j <br /> Containment Plpe A B C D E L ______'1__- <br /> Inches In_ In. In. In. In. ---' _ <br /> 3 7.50 10.60 8.50 10.00 14.50 ® n <br /> 4 8.50 12.00 7.50 12.00 16.50 <br /> 6 10.615 15.00 8.00 14.75 22.00 1 <br /> a au^raa"e <br /> Containment Pipe A B C D E <br /> MM mm trm nim mm mrrl n <br /> 75 191 269 165 254 369 <br /> 100 216 305 191 305 a1g Sump Entry/Termination Fitting with Gasket <br /> 150 271 381 203 375 559 (Refer to 62109 for installation information) <br /> /Sump wan <br /> • • Gesw <br /> Gskee <br /> s A ll���JJ <br /> Nix <br /> t B <br /> o • i <br /> 2.5" • <br /> I <br /> _ * NOTE:The 2.5" Hae <br /> (64mm)critical Da <br /> dimension must <br /> C be inspected In -1 <br /> O— the field. <br /> E Entryriefttinetbn e g 6my <br /> C.,essXn Ring <br /> 14 <br />