ARCHIVED REPORTS_XR0002484 - Laserfiche WebLink

Home Browse Search

si Soil borings which are not to be converted into monitoring wells are sealed to the ground surface using neat cement or sand-cement slurry in accordance with federal, state and local regulations Native soil may be used to fill the top two to three feet for cosmetic purposes,as pemutted Monitoring Well Installation Wqll Casing. cMen and]Eilter PackConstruction All well construction is performed in accordance with Department of Water Resources "California Well Standards" and all requirements of local oversight agencies Soil bonngs to be converted into single-cased morutonng wells are a minimum of eight inches in diameter for 2-inch diameter wells and a minimum of ten inches in diameter for 4-inch diameter wells Monitoring wells are constructed with schedule 40,threaded,polyvinyl chloride (PVC)casing unless site geochemistry or contamination necessitates an alternative material The wells are constructed with factory- slotted screen and threaded end caps The screened interval is placed such that it extends approximately ten feet into the water bearing zone, and at least five feet above the expected maximum water level The screened interval may extend less than five feet above the maximum water level, only to prevent intersection of the screened interval with the top of the confining layer of a confined aquifer,or where the water table is too shallow to allow this construction A graded sand filter pack is placed in the annular space across the screened interval and extended approximately one to two feet above the screen, as site conditions permit, so as to prevent extension of the sand pack into an overlying water-bearing unit The well screen slot size is the maximum size capable of retaining 90% of the falter pack Typically, 0 010-inch screen is used where the formation is predominantly clav and/or silt or poorly-graded fine sand 0 020-inch screen is used where the formation is predominantly well-graded or medium to coarse sand and/or gravel The filter pack grade (mean grain size) is selected according to native sediment type as follows a) for poorly graded fine sand or silt/clay - 4 times the 70% retained grain size of the formation b) for medium to coarse sand gravel or well graded sediments - 6 times the 70% retained grain size Since results of particle size analysis are not always available, Clearwater often selects screen size and filter pack on the basis of general site stratigraphy,and specifically the finest significantly thick layer of sediment to be screened Commonly selected grades are Lone Star@ 3, 2/12 or 2/16 (or equivalent) with 0 020-inch slotted screen and Lone Star@ 1120 with 0 010-inch slotted screen Well Seal A minimum two foot seal of bentonite is placed above the sand pack The bentonite seal is hydrated by either formation water or potable water Neat cement or a cement/bentonite grout mixture seals the remaining annular space to the surface If bentonite is used in the grout mixture, it does not exceed 5% by weight The grout is placed using a tremie pipe, if the top of the bentonite is more than 20 feet below grade, or if water is present in the boring above the bentonite seal- A watertight locking cap and protective traffic-rated vault box is installed on top of each well Well construction details are presented on the Field Exploratory Soil Boring Log Following completion of a well, Clearwater completes and submits, or ensures that the driller has sufficient information to complete and submit,the state-required Well Completion Report or equivalent document. Well Development All newly installed wells are developed prior to sampling to remove fine grained sediments from the well and stabilize the filter pack and the disturbed aquifer materials Development takes place prior to or at least 24 hours after setting the seal on the well, unless otherwise directed by a local oversight agency Well development consists of surging with a surge block and removing water from the well with either a pump or bailer, until the well is free of sediment,or until at least 10 well casing volumes have been removed Depth to bottom is measured to determine casing volume If the well is sampled immediately following development, temperature, pH, specific conductance and turbidity (qualitative) are monitored during well development (see section Groundwater Sampling") All development equipment is cleaned prior to use and between wells with an Alconox@ solution,then rinsed in potable water All data collected during development are recorded on the Well Development Data Sheet and,if necessary,the Purging Data Sheet. CLEAitwATlEiz GROUP,INC.(WI/GWS) 2 revised September 30, 1999