Laserfiche WebLink
Site Preparatia ad Installation InstructionsT <br /> TI-S-350 UST Monitoring System <br /> 4. Type A Sensors. F. RELAY OUTPUT WIRING. <br /> Connect the two marked or color-coded wires from each TLS-350 Relay Output Modules incorporate four Form-C <br /> sensor to the appropriate terminals on the Type A relay outputs,and the UO Combination Modules incorpo- <br /> Interface Module connector (see Figure 16, "Type A <br /> Interface Mode Wiring Diagram"). Be sure to main- rate two. These relays may be connected to external <br /> tsystema or devices that do not draw more than ZA. <br /> ain the proper polarity between the sensor wires <br /> and their respective module connector terminals. ]MPORTANT! ONCE OUTPUT RELAYS HAVE BEEN <br /> CONNECTED TO EXTERNAL DEVICES AND THE <br /> SYSTEM HAS BEEN STARTED AND PRO- <br /> SENSDR►f:T'T'TT'T'T'T'1 IFl,N1Y.F,FfFF GR.AMIViED,MODULEPOSITIONS,CONNECTOR <br /> °uvur Funs POSITIONS AND WIRE POSITIONS CANNOT BE <br /> TYPE A INT E MODULE C� CHANGED WITHOUT REPROGRAMMING THE <br /> ' SYSTEM! <br /> -MODULE IMPROPER SYSTEM OPERATIONWILLRESULT <br /> IFANY ONE OFTHESE POSITIONS IS CHANGED <br /> 0 0 0 0 0 0 0 0 0 0 0 0 0 0'0 0--CONNECTOR WITHOUT REPROGRAMMING. <br /> WARNING: ALARM RELAYS CANNOT BE <br /> USED FOR FLOW CONTROL.ALARM RELAYS <br /> PROVIDE ONLY A MOMENTARY CLOSURE <br /> -- -- AND CANNOT ACTUATE FLOW CONTROL <br /> DEVICES SUCH AS VALVES AND PUMP MO- <br /> RIGID TOR RELAYS. <br /> CONDUIT MONITOR <br /> UP TOB <br /> SENNSORS Be sure to accurately record on the circuit directory the <br /> type of module and the location of each device wired to the <br /> connector. <br /> SENSOR SENSOR SENSOR <br /> Identify each connector with a self-adhesive number label <br /> according to the slot number. <br /> Figure 16. Type A Interface Module Wiring Diagram DO NOT CONNECT OUTPUT RELAYS TO A DE- <br /> VICE THAT DRAWS MORE THAN 2 AMPSI <br /> 5.Type B Sensors. Output Power.Output Relay Contact,Resistive Load— <br /> Connectthethree marked orcolor-codedwires from each 120 VAC,2A Max.;or 24 VDC, 2A Max. <br /> sensor to the appropriate terminals on the Type B 1.Connect the wires(#14 AWG)from each external device <br /> Interface Module connector (see Figure 17, "Type B to the appropriate terminals on the output module(see <br /> Interface Module Wirng Diagram").Be sure to main- <br /> tain the proper polarity between the sensor wires Figure 18,"Relay Output Module Wiring Diagram,"or <br /> and their respective module connector terminals. Figure 19,"1/0 Combination Module Wiring Diagram"). <br /> RELAY•K+ocT.F':°'c'—.°'cc FF <br /> 4-RELAY T MODULE <br /> O <br /> TYPE 8 A E MODUIE <br /> MODULE <br /> MODULE <br /> 000000000000000000 0 CONNECTOR 0 0 0 0 0 0 0 0 0 CONNECTOR <br /> • I I I <br /> I I <br /> II II <br /> I I I I <br /> I I I I <br /> I I I I <br /> MONITOR <br /> RIGID PT I I <br /> CONOUIT SENSOAS <br /> —� <br /> RIGID I MONITOR <br /> CONDUITi UPTOE 1 1 <br /> `EXTERNAL—+I I <br /> DEVICES <br /> I I <br /> SENSOR 5 N R rK NO C NC Iq C <br /> EXTERNAL Es iERNAL <br /> DE—E OEvICE <br /> Figure 17. Type B Interface Module Wiring Diagram. Figure 18. Relay Output Module Wiring Diagram. <br /> 19 <br />