INSTALL_2005 - Laserfiche WebLink

Home Browse Search

Spill Containn OPW EVR Thread-on or OPW/POMECO EVR Multi-Port spill containers are certified for installation on OPW Phase I EVR systems. All fill ports in these spill containers feature enhanced 1 DK-2100-EVR vapor tight drain valves that exceed the EVR requirements for r a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.The vapor return spill containers feature a permanent plug installed in the drain ports as per EVR requirements. r Overfill Preventie The OPW 61 SO-400C-EVR series Overfill Prevention Valves are certified for installation on the OPW Phase 1 EVR system.The vapor tight EVR 61 SO's are designed to provide positive shut-off of product delivery, before an overfill condition occurs, per EPA requirements, without intervention from the transport driver.The valve features a sealed float pivot and a threaded lower tube connection and exceeds the EVR requirement for a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O.The 61 SO-EVR series valve is installed in the base of the OPW EVR spill container with the patent pending 611SK Jack Screw device.This configuration allows ;,. liquid in the spill container to be drained directly into the drop tube,thereby isolating the drain valve from the tank ullage,eliminating a notorious leak point in previous systems. �J, q .. Tank BGiwi-ii vii The OPW/POMECO 6111-1400 Tank Bottom Protector is EVR certified �y, for installation at the bottom of the overfill prevention valve drop tube to help prevent the i underground storage tank from sustaining damage from erosion or tank gauging sticks. 5 Extra The OPW 53VML Ball Float, 233 Extractor and 61 T Fill Drop Tube configuration can be installed as an alternative to the 61 SO Overfill application.The installation of the Ball Float/Drop Tube system is identical to the 61 SO Overfill valve on Phase 1 Vapor Recovery Systems. SVV (Fill and Val::., OPW EVR Rotatable Swivel Adaptors are certified for installation on the fill and vapor ports on OPW Phase 1 EVR systems. OPW Swivel Adaptors Provide 360 degrees of rotation of any product or vapor recovery elbow to prevent the adaptors from loosening on the spill container risers. OPW Swivel Adaptors exceed the EVR requirement to maintain a minimum 360-degree rotation with an average static torque not to exceed 108 inch- pounds (9 foot pounds).The enhanced poppet system on the OPW 61 VSA-EVR vapor swivel adaptor provides a vapor tight seal when closed, per EVR requirements. Adaptor Tool An OPW 61SA-TOOL Adaptor installation tool is required to ensure proper installation of DPW Rotatable Swivel Adaptors,spill containers and threaded riser adaptors, per ..f EVR requirements.The 61 SA-TOOL includes provisions for the use of a torque wrench to facilitate accurate installation and testing. r!� 11cict r ye (Fill a. Vann, OPW EVR Dust Caps are certified for installation on OPW EVR certified Rotatable Adaptors. OPW EVR Certified Dust Caps feature enhanced ribbed seals and increased sealing forces to provide a bubble-tiht seal per EVR requirements.Available in Duratuff or low profile metal modes. MINION rp - lded Rises ^ 'T coal Adapte An OPW FSA-400 Threaded Riser Face Seal Adaptor is required to provide a flat,true sealing surface on threaded pipes where a gasket seal exists per EVR requirements. The FSA-400 is installed on the fill pipe riser below the spill container to provide a true sealing surface for the drop tube flange on the 61 SO-40OC-EVR overfill prevention valves. The FSA-400 is also required on tank gauging risers,though is optional on vapor risers and rotatable adaptors. Pressure Vacuum Ven The OPW 623V Pressure Vacuum Vent is certified for installation on the OPW Phase 1 EVR System.The 623V's are installed on the top of the vent pipes for underground fuel storage tanks. The vent cap and internal wire screen are designed to protect the tank vent lines against intrusion and blockage from water, debris or insects.A normally closed poppet in the valve opens at a predetermined pressure or vacuum setting to allow the tank to vent.The 623V exceeds the EVR requirement of a maximum vapor leak rate of 0.17CFH at 2.0 inches H2O. 9393 Princeton-Glendale Road • Cincinnati,Ohio 45011 Tel: (800) 422-2525 Fax: (800) 421-3297 • www.opw-fc.com c 2003,OPW Fueling Components P EVR-8/03-5M