|
EXISTING GASIELECTRIC ROOFTOP UNIT SCHEDULE MECHANICAL GENERAL NOTES
<br /> SYMBOLS AND LEGEND
<br /> INDOOR FAN HEATING COOLING ELECTRICAL
<br /> NOMINAL OPERATING
<br /> SYMBOLS MAKE & MODEL AREA SERVING TON AIR FLOW OUTSIDE AIR E.S.P. GAS INPUT GAS OUTPUT STAGE TOTAL SENSIBLE AMBIENT DB ENTERING VOLTAGE MCA MOCP EER / SEER EIGHT (LBS. REMARKS 1. MECHANICAL CONTRACTOR SHALL VISIT THE JOB SITE AND THOROUGHLY EXAMINE ALL EXISTING SYMBOL DESCRIPTION (USE AS APPLICABLE)
<br /> {CFM} (CFM) (INCH. W.G,} (MBH) (MBH} {MBH) (MBH) ('F) DB ('F) WB ('F) {VOLT-4-Hz) (AMPS.) (AMPS.) CONDITIONS WHICH MAY AFFECT HIS WORK PRIOR TO SUBMITTING HIS BID. THE CONTRACTOR SHALL
<br /> EXAMINE ALL PROJECT DRAWINGS AND SPECIFICATIONS AND SHALL INCLUDE ALL NECESSARY LABOR ANDDETAIL 1/SHEET M1
<br /> ''��JJ�i
<br /> E) 1C 8TJRA
<br /> D0 4 DINING 12.0 5000 1800 0.5 225 180 2 95.2 72.1 95 80 67 208-3-60 60 80 8,6 / - 1264 ACCESSORIES 1 TO 6. MATERIALS IN HIS PROPOSAL FOR MECHANICAL. SYSTEMS TO PROVIDE COMPLETE OPERATIONAL SYSTEMS.ANY DISCREPANCIES NOTED SHALL BE REPORTED TO THE ARCHITECT/ENGINEER PRIOR TO BID,
<br /> SECTION A/SHEET M1
<br /> AC CARRIER DINING, ENTRY & 2. THE MECHANICAL CONTRACTOR SHALL COMPLY WITH ALL 2016 EDITIONS OF CALIFORNIA MECHANICAL
<br /> E)/' 2 48TJD012 RESTRODMS 10.0 4000 1500 0,5 180 144 2 95.2 72.1 95 80 67 208-3--60 49.9 60 8.9 / - 1244 ACCESSORIES 1 TO 6, CODE, CALIFORNIA BUILDING CODE, CALIFORNIA ELECTRIC CODE, LOCAL, STATE, FEDERAL SAFETY, 1 ROYASSOC
<br /> SERVICESCUPATIONAL AND NATIONAL CODE. _ EQUIPMENT MARK N0. AC-1/SEE EQUIPMENT SCHEDULE ESIAT
<br /> E) AC CARRIER COOKLINE & 7.5
<br /> 3000 1000 0.5 125 100 1 95.2 72.1 CONSULTING ENGINEERS
<br /> 48TJD008 BAKERY 95 8D 67 208-3-60 40,2 45 8.9 / - 1068 ACCESSORIES 1 TO 6. 3. FURNISHING OF ALL LABOR, MATERIALS AND SUPPLIES NECESSARY FOR THE CONSTRUCTION AND LINEAR SLOT DIFFUSER
<br /> 3
<br /> COMPLETION OF THE WORK SHOWN ON THE DRAWINGS AND SPECIFICATIONS IS THE RESPONSIBILITY OF
<br /> AC CARRIER SERVICE PREP, THE CONTRACTOR UNLESS OTHERWISE NOTED.
<br /> E) --m- SUPPLY GRILL CEILING WITH DIRECTION OF AIR FLOW 39510 PASEO PADRE PKWY,
<br /> 5. .5 74 59.2 1 95,2 72.1 95 80 67 208-3-60 29.4 35 - / 10 654 ACCESSORIES 1 TO 6. � A
<br /> 4 48TJD006 TCHEN & OFFICE 0 2000 720 04. MECHANICAL HVAC DRAWINGS ARE PREPARED BASED ON THE AVAILABLE INFORMATION AND SHALL NOT BE SUITE 250
<br /> SCALED FOR EXACT LOCATIONS, FIELD CONDITIONS, NON-INTERFERENCE WITH OTHER UTILITIES AND RETURN GRILL CEILING FREMONT, CALIFORNIA 94538
<br /> ®
<br /> TRADES, SHALL DETERMINE EXACT LOCATIONS, Tel.: 510 794 .8091
<br /> EXHAUST GRILL CEILING
<br /> 5. ALL HVAC DUCTWORK, EQUIPMENT AND CONTROLS SHALL MEET THE CALIFORNIA ADMINISTRATION CODE Fax: (510) 794-7250
<br /> ACCESSORIES: TITLE 24 REQUIREMENTS FOR NON--RESIDENTIAL BUILDINGS. ® ROUND DUCT UP Email: ro @r0 ossociates.com
<br /> 1. THERMOSTAT (S). A PROGRAMMABLE ELECTRONICALLY LOCKABLE THERMOSTAT, 6. ALL HEATING, VENTILATING & AIR CONDITIONING SYSTEMS SHALL BE PROVIDED WITH AN AUTOMATIC ® SUPPLY DUCT UP This drawing embodies Ideas designs,
<br /> 2, SUPPLY AIR AND RETURN PR DUCT SMOKE DETECTOR, SETBACK TEMPERATURE CONTROLLER WHICH IS CAPABLE OF AT LEAST TWO SET BACK SETTING IN A 24 arrangements,� tRoy�let'm and°twh`ch ere"°
<br /> ® designed, created, evolved and developed for use
<br /> 3. FACTORY ROOF CURB. HOUR PERIOD. MOUNT THERMOSTAT AT 4'-0" ABOVE FINISHED FLOOR. RETURN DUCT UP ad*in connection with the specified project for
<br /> Roy Associates use only. No transfer of any rights
<br /> 5.4. DEMAND CONTROL VENTILATION. thane to be Intended or affected by delivery
<br /> 7. THE HEATING SETP-DINT MUST BE ADJUSTABLE DOWN TO 55-F OR LOWER, AND THE COOLING SET-POIN ® hereof.And except upon written permission of Roy
<br /> TWO STAGE GAS HEATING. EXHAUST DUCT UP AseoClates this drawing is not to be disclosed to
<br /> UP TO 85'F OR HIGHER, PROVIDE AT LEAST A 5'F DEAD-BAND BETWEEN HEATING AND COOLING others, reproduced or°opted In whole or In part
<br /> 6. PROVIDE 100% ECONOMIZER WITH BAROMETRIC RFLIEF AND ECONOMIZER CONTROL. or used in the fabrication,to
<br /> discng. and
<br /> SETP-Q1NT5. construction of building(s), structures, foundations,
<br /> ROUND DUCT DN, design guidelines,or any portions thereof for
<br /> other than Roy Aseaclates specific use alone.
<br /> 8. ALL DIFFUSER, GRILLE AND REGISTER LOCATIONS SHALL BE COORDINATED WITH THE ARCHITECTURAL AND Thew drawings and use of can be revoked at orry
<br /> time by Roy Associates including removal from
<br /> ELECTRICAL REFLECTED CEILING PLANS. z SUPPLY DUCT DN. Building and planning Department upon demand
<br /> EXISTING AND NEW EXHAUST FAN SCHEDULE
<br /> without Roy
<br /> °°�.
<br /> KITCHEN EXHAUST SYSTEM NOTE �� EQUIPMENT ACCESS SHALL CONFORM TO CMC 2016 EDITION AND CLEARANCES FROM COMBUSTIBLES ,� RETURN DUCT DN. copyright Roy Associates
<br /> SHALL BE AS 2016 EDITION,
<br /> SYMBOLS MAKE & MODEL SERVICE
<br /> AIR FLOW E.S.P. WEIGHT 10, IF ANY EQUIPMENT SUBMITTED FOR APPROVAL HAS A DIFFERENT PHYSICAL SIZE OR ARRANGEMENT FROM EXHAUST DUCT DN, pEipf Essi oN
<br /> (CFM) TYPE DRIVE (INCH. W.G.) FLA ELECTRICAL VOLTAGE REMARKS 1. THE KITCHEN EXHAUST FAN HOOD AND DUCTWORK INSTALLATION SHALL COMPLY WITH THE '` o '��
<br /> HP (AMPS.) RPM (V-0-Hz.) (LBS.} CALIFORNIA MECHANICAL CODE, 2016 EDITION, CHAPTER 5, FOR COMMERCIAL HOODS AND KITCHEN INSTALLATION DETAILS. DRAWINGS, A FULL SET OF SHOP DRAWINGS SHALL BE SUBMITTED SHOWING ALL SHEET METAL DUCT (ROUND OR RECTANGULAR) ��� yPapT K Rar `Ay
<br /> VENTILATION SYSTEMS.
<br /> EF DONALDSON tel'
<br /> E) 1 PH24F EXISTING Hoop-1 3850 - BELT 1.0" 1 Y - 720 208-3-60 770 ACCESSORIES 4, 5, 6, 7 8 2. ALL MAKE-UP AIR SUPPLY DUCT MATERIAL AND FABRICATION SHALL CONFORM " 11, PROVIDE A MINIMUM OF TEN (10) FEET BETWEEN OUTSIDE AIR INTAKES AND PLUMBING VENTS OR S-�-- DUCT WITH ACOUSTIC LINING NO. M19038
<br /> M TO THE HVAC DUCT EXHAUST FAN OUTLETS, ExP. os-338
<br /> EF DONALDSaN
<br /> CONSTRUCTION STANDARDS" AS PUBLISHED BY SMACNA LATEST EDITION & SHALL COMPLY WITH �. FLEXIBLE DOUBLE LINE DUCT s
<br /> 0-20
<br /> CHAPTER 6 OF THE CALIFORNIA MECHANICAL CODE, 2016 EDITION. THE MECHANICAL CONTRACTOR 12. COORDINATE ALL CUTTING, FRAMING AND PATCHING WITH THE GENERAL CONTRACTOR.
<br /> E 2 RA24F EXISTING HOOD-2 3850 BELT 1.0" 1 Y - 720 208-3-60 770 ACCESSORIES 4, 5, 6, 7 & 8 1 qT �cA�1�p�o �.
<br /> SHALL PROVIDE DIMENSIONED SKETCHES OF THE MAU DISCHARGE ELBOWS FOR APPROVAL BY ROY
<br /> 3 ASSOCIATES. 13
<br /> F �. IT SHALL BE THE CONTRACTORS RESPONSIBILITY TO FIELD VERIFY THE EXACT ROUTING AND SPACE C 1+� F
<br /> ELBOW WITH TURNING VANES o
<br /> AVAILABLE FOR ALL DUCT RUNS, EQUIPMENT LOCATIONS, AND PENETRATIONS THROUGH EXISTING
<br /> N
<br /> CAPTIVE AIRS SYSTEM NEW HOOD-3 1920 UPBLAST BELT 1.25" N4 8.8 1459 115-1-60 97 ACCESSORIES 4, 5, 6 & 7 3. ALL MAKE-UP AIR DUCTS TO INDIVIDUAL DIFFUSERS SHALL BE SUPPLIED WITH MANUAL VOLUME
<br /> EXISTING
<br /> DU85HFA DAMPERS. STRUCTURES. 8"0 CD-4 AIR INLET OR OUTLET NECK SIZE, TYPE, FLOW DIRECTION E)
<br /> EF LOREN COOK 14, LOW VOLTAGE WIRING TO THE THERMOSTATS SHALL BE BY THE HVAC SUBCONTRACTOR. 120 VOLT 200 CFM & AIR QUANTITY
<br /> 4 ACRU---B-150R2B HOOD-4 DISHWASHER 1000 UPBLAST BELT o.25" 0.16 - 680 120-1-60 85 ACCESSORIES 1, 2, 3, 4 & 5 4. EQUIPMENT ACCESS SMALL CONFORM TO UMC SECTION 305 AND CLEARANCES FROM COMBUSTIBLES RELAYS, WALL SWITCHES AND LIGHT SWITCHES CONTROLLING THE EXHAUST FANS SHALL BE PROVIDED 48"x2x1 2"
<br /> LD SHALL BE AS INDICATED IN THE 2016 CBC AND CMC WORKING SPACE CLEARANCES SHALL BE AS AND WIRED BY THE ELECTRICAL CONTRACTOR. 150 CFM
<br /> TRAPNEAR DIFFUSER, LENGTH x NO. SLOTS x SLOT WIDTH
<br /> REQUIRED BY THE NECNEG 2014. & AIR QUANTITY
<br /> VQT
<br /> EF 300 15. AT THE COMPLETION OF THE PROJECT, THE HVAC SYSTEMS SHALL BE PLACED IN OPERATION AND QT THERMOSTAT 54
<br /> F) 5
<br /> TRADEWIND
<br /> MEN RESTROOM 290 CEILING DIRECT 0,375" Ya - 700 120-1-60 25 ACCESSORIES 2, 3, 4, 9 & 10
<br /> 5. IF ANY EQUIPMENT SUBMITTED FOR APPROVAL HAS A DIFFERENT PHYSICAL SIZE OR ARRANGEMENT
<br /> FROM THAT SHOWN ON THE DRAWINGS SHOP DRAWINGS, SHOWING ALL INSTALLATION OF DETAILS, CYCLED THROUGH THE COMPLETE HEATING AND COALING PROCESSES TO DEMONSTRATE THEIR N
<br /> EF TRADEWIND FUNCTIONAL CAPABILITIES, ALL TESTING, ADJUSTING AND BALANCING SHALL BE IN ACCORDANCE WITH
<br /> E)� VQT-300 WOMEN RESTROO 290 CEILING DIRECT 0,375" Yo - 700 120-1-60 25 ACCESSORIES 2, 3, 4, 9 & 10 SHALL BE SUBMITTED TO THE ENGINEER FOR REVIEW AND APPROVAL, NEBB OR AABC STANDARDS. ® PRESSURE SENSOR
<br /> EF TRADEWIND FEMALE EMPLOYEE
<br /> 6. PROVIDE A MINIMUM OF TEN FEET (10') BETWEEN OUTSIDE AIR INTAKES AND ANY PLUMBING VENTS 16. HEATING AND COOLING SYSTEMS IN EXCESS OF 2000 CFM SHALL BE EQUIPPED WITH AN AUTOMATIC SD DUCT SMOKE DETECTOR
<br /> E) 7 VQT-200 LOCKER 204 CEILING DIRECT 0.375" Y0 - 600 120-1-60 25 ACCESSORIES 2, 3, 4, 9 & 10 OR EXHAUST FAN OUTLETS. SHUTOFF ACTIVATED BY SMOKE DETECTORS PER SECTION 608 - CMC 2016. SMOKE DETECTORS SHALL
<br /> 7. COORDINATE ALL CUTTING, FRAMING AND PATCHING WITH THE GENERAL CONTRACTOR. BE WIRED BY FIRE ALARM CONTRACTOR. FSD� FIRE AND SMOKE DAMPER WITH ACCESS DOOR IN DUCT W
<br /> EF TRADEWIND MALE EMPLOYEE 17. FOR ADDITIONAL INFORMATION REFER TO ARCHITECTURAL DRAWINGS. W
<br /> E) 8 VQT---200 LOCKER 200 CEILING DIRECT 0.375" Yp - 600 120-1-60 25 ACCESSORIES 2, 3, 4, 9 & i 0 8. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO FIELD VERIFY THE EXACT ROUTING AND SPACE F-D• FUSIBLE LINK FIRE DAMPER
<br /> TRADEWIND
<br /> AVAILABLE FOR ALL DUCT RUNS, EQUIPMENT LOCATIONS, AND PENETRATIONS THROUGH STRUCTURES. 18. PROVIDE FAN SUPPORT IN ACCORDANCE WITH MANUFACTURERS RECOMMENDATIONS. V
<br /> EF 1----
<br /> E) 9 VQT-200 JANITOR AREA 200 CEILING DIRECT 0,375" Yo - 600 120-1-6025 ACCESSORIES 2, 3, 4, 9 & 10 9. EXHAUST FAN INSTALLATION AND MOUNTING DETAILS SHALL BE AS RECOMMENDED BY THE 19. PROVIDE FIRE AND SMOKE DAMPERS AT ALL DUCT PENETRATIONS THROUGH ONE HOUR :FIRE RATED BD BALANCE DAMPER / MANUAL VOLUME DAMPER
<br /> MANUFACTURER AND LOCAL AUTHORITY HAVING JURISDICTION. WALLS, c
<br /> ® SQUARE TO ROUND TRANSITION W
<br /> 1. ALUMINIZED BIRD SCREEN. Q
<br /> ACCESSORIES: 10. THE EXHAUST FAN AND MAKE-UP AIR UNIT FOR EACH KITCHEN HOOD SHALL BE INTERCONNECTED 20. ALL DIFFUSERS AND REGISTERS SHALL BE SUPPLIED WITH MANUAL VOLUME DAMPERS.
<br /> BY AN ELECTRICAL INTERLOCKING SWITCH. IM
<br /> 2. SPEED CONTROL SWITCH MOUNTED TO FAN CABINET FOR EXACT BALANCING. 11FILTERS SHALL BE IT21. DUCT FABRICATION AND INSTALLATION, INCLUDING SUPPORTS, SHALL CONFORM TO THE "IHVAC DUCT ® SMOOTH RADIUS ELBOW BELOW RISER k v
<br /> . INSTALLED AT AN ANGLE NOT LESS THAN 45 DEGREES FROM THE HORIZONTAL CONSTRUCTION STANDARDS" AS PUBLISHED BY SMACNA LATEST EDITION, AND SHALL COMPLY WITH THE
<br /> 3. GRAVITY BACK DRAFT DAMPER.
<br /> 4. SAFETY DISCONNECT SWITCH. AND SHALL BE EQUIPPED WITH ADRIP TRAY BENEATH THE LOWER EDGE OF THE FILTERS. CMC 2016 EDITION. -- --� LINE CONTINUED
<br /> 5. EQUIPMENT CURB. 12. KITCHEN EXHAUST HOOD SHALL BE CONSTRUCTED OF STAINLESS STEEL AND SHALL NOT BE LESS 22. A THERMOSTAT MUST BE PROVIDED TO CONTROL HEATING AND COOLING TO EACH ZONE. THE HEATING '�
<br /> 6. GREASE BOX. THAN 0.043 NCH (N0. 18 GA.}. UNLESS INDICATED OTHERWISE ON DRAWING. EVERY JOINT AND SET-POINT MUST BE ADJUSTABLE DOWN TO 55'F OR LOWER, AND THE COOLING SET--POINT UP TO SINGLE INLET VARIABLE AIR VOLUME BOX C4
<br /> 7. COORDINATE WITH MANUFACTURER FOR FINAL SELECTION. SEAM SHALL BE SUBSTANTIALLY TIGHT. SOLDER SHALL NOT BE USED EXCEPT FOR SEALING A JOINT 85'F OR HIGHER. PROVIDE AT LEAST A 5F DEAD-BAND BETWEEN HEATING AND COOLING SETP-DINTS.
<br /> 8. DISCHARGE SCOOP. OR SEAM. THE EXHAUST HOOD SHALL BE SECURELY FASTENED IN PLACE BY NON-COMBUSTIBLE k,-7
<br /> 1 ROOF CAP S WALL CAP. SUPPORTS. i_`u J ACCESS PANEL �
<br /> 10. MOUNTING ASSEMBLY.
<br /> 13. CLEANOUT OPENINGS SHALL BE EQUIPPED WITH TIGHT-FITTING DOORS CONSTRUCTED OF STEEL - -�]CO PIPE CLEANOUT TEE
<br /> HAVING A THICKNESS NOT LESS THAN THAT REQUIRED FOR THE DUCT. DOORS SHALL BE EQUIPPED
<br /> WITH A SUBSTANTIAL METHOD OF LATCHING, SUFFICIENT TO HOLD THE DOOR TIGHTLY CLOSED. t
<br /> DOORS SHALL BE SO DESIGNED THAT THEY CAN BE OPENED WITHOUT THE USE OF A TOOL. �--D DUCT DOWN N
<br /> EXISTING MAKE UP AIR UNIT AND DUCT HEATER SCHEDULE DUCT AND INSULATION SCHEDULE GREASE DUCT FIRE PROTECTION DUCT UP
<br /> NOTES
<br /> 45' LATERAL (REDUCING OR WITH REDUCER)
<br /> GAS ELECTRICAL
<br /> SYMBOLS MAKE & MODEL SERVICEATE ISSUE FOR BY
<br /> RIR FLOW GAS INPUT E.S.P.„ . WEIGHT DUCT TYPE PRESSURE CLASS SEAL LEVEL INSULATION
<br /> (CFM) {MBH} OUTPUT (INCH. W.G.) HP FLA RPM VOLTAGE (LBS) REMARKS 1. FIRE EXTINGUISHING SYSTEM FOR PROTECTION OF KITCHEN GREASE GOODS AND DUCTS SHALL BE REDUCING Y- BRANCH
<br /> (MBH) (AMPS.) (V--0-Hz.) SUPPLY AIR t 1” W.G. B R-8 DESIGN BUILD: 5-01-19 100% DEMO PIAN SR E} MAU LSR1413A (E) HOOD-1 & 2 6930 - 0.7" 2 - - 208-3-60 808770 208V-1 -60Hz PUMP, BACKDRAFT DAMPER, DOUBLE BELTS AND A. AN APPROVED UL 300 COMPLIANT EXTINGUISHING SYSTEM SHALL BE PROVIDED FOR THE PROTECTION SHOE TYPE 90' TEE (REDUCING OR WITH REDUCER) 07-02-19 CITY/HEALTH susMfnal. SR
<br /> DRIVES AND DUCT HEATER, RETURN AIR t 1" W,G, B R-8 OF THE COMMERCIAL FOOD HEAT-PROCESSING EQUIPMENT, [2016 CMCJ NEW FLEXIBLE OR SHEET METAL DUCTS (PER DUCTWORK SPECIFICATION)
<br /> REZNE-3 HEAT EXCHANGER & BURNERS, ELECTRONIC SPARK
<br /> DH
<br /> E) HRXZ-4000 (E) MAU-1 6930 4000 308 0,27" 1 Y 0.17 120-1-60 405 IGNITION, MECHANICAL_ MODULATING GAS VALVE AND 36" HIGH EXHAUST ± 1" W.G. C NONE B. THE FIRE-EXTINGUISHING SYSTEM USED FOR THE PROTECTION OF COMMERCIAL COOKING EQUIPMENT
<br /> FLUE EXTENSION SHALL BE EITHER A SYSTEM LISTED FOR APPLICATION WITH SUCH EQUIPMENT OR AN AUTOMATIC EXISTING FLEXIBLE OR SHEET METAL DUCTS (PER DUCTWORK SPECIFICATION)
<br /> FIXED PIPE SYSTEM THAT IS SPECIFICALLY DESIGNED FOR SUCH APPLICATION. LISTED SYSTEMS
<br /> SHALL BE INSTALLED IN ACCORDANCE WITH THEIR LISTING. OTHER SYSTEMS SHALL BE OF A DESIGN/ EXISTING DUCTWORK OR EQUIPMENT TO BE DEMOLISH
<br /> APPROVED BY THE ADMINISTRATIVE AUTHORITY HAVING JURISDICTION. [2016 CMC]
<br /> C. FIRE EXTINGUISHING SYSTEM SHALL BE DESIGNED AND INSTALLED PER NFPA 96 STANDARDS. SYSTEM PQ PONT OF DISCONNECTION SHEET CONTENT:
<br /> EXISTING AND NEW KITCHEN EXHAUST HOOD SCHEDULE AIR INLET / OUTLET SCHEDULE SHALL BE INTERCONNECTED TO THE BUILDINGS FERE PANEL AND SHALL BE SUPERVISED iBY CENTRAL
<br /> STATION MONITORING SYSTEM. PQC POINT OF CONNECTION ��SAL.
<br /> LENGTH COOKING EXHAUST HOOD D, CONTRACTOR TO PROVIDE AT LEAST THREE (3) COPIES OF WORKING DRAWINGS, CALCULATIONS AND U— AIRFLOW UNDER DOOR NOTM SYIIOWL.EGIM,
<br /> SYMBOLS MAKE & MODEL. SERVICE TEMPERATURE AIR FLOW COLLAR SIZE E.S.P. CONSTRUCTION WEIGHT
<br /> REMARKS CD SQUARE CEILING DIFFUSERS SHALL BE THE SQUARE / RECTANGULAR MODULAR CORE DIFFUSERS PERMIT APPLICATION, AND FEES TO THE BUILDING DEPARTMENT FOR APPROVAL. O SHEET NOTE WECIR AMOM M KET
<br /> (FT.-IN.) (.F) LBS FLUSH FACE TYPE, FABRICATED FROM ALUMINUM, 1, 2, 3 OR 4 CURES PER AIR FLOW PATTERN ON E. A READILY ACCESSIBLE MANUAL ACTIVATING DEVICE SHALL BE INSTALLED IN AN APPROVED LOCATION. SA SUPPLY I OUTLET AM EOLMNT
<br /> (CFM) (IN. 0) (INCH. W.G.) MATERIAL
<br /> U LY A R
<br /> CAPTIVE AIRE 430 CEILING PLAN. NECK SIZES AND DISCHARGE PATTERNS ARE INDICATED ON THESE MECHANICAL [2016 CMC] QA OUTSIDE AIR SCFEDULB
<br /> E) SYSTFM COOKING LINE 11'-3" 700 3850 24"x12" -- STAINLESS STEEL (E) NOTE # 1 DRAWINGS. THE NOMINAL MODULE SIZE SHALL BE 24"x24" OR 48" x 24" WITH LAY-1N OR SURFACE RA RETURN AIR
<br /> 4224 VHB 100% MOUNT BORDER, THE WHITE ANODIC ACRYLIC PAINT MUST PASS ASTM D117, 870 AND D-2794 F. A SYSTEM TEST SHALL_ BE WITNESSED BY BUILDING DEPARTMENT PRIOR TO ANY PORTION BEING EA EXHAUST AIR
<br /> CAPTIVE AIRE 430 TESTS. ALL SUPPLY DIFFUSERS SHALL BE SUPPLIED WITH SLING OR OPPOSED BLADE DAMPERS AND CONCEALED. GIVE AT LEAST 48 HOURS NOTICE FOR INSPECTION BY THE FIRE MARSHAL. TC 7 DAY TIME CLOCK W/BATTERY BACKUP
<br /> E) 2 SYSTEM COOKING LINE 11'-3" 700 3850 24"x12" - STAINLESS STEFL (E) NOTE # 1 EARTHQUAKE TABS. DIFFUSERS SHALL BE METAL AIRE MODEL 9000 SERIES FOR 24x24 MODULE AND V/0/Hz VOLT / PHASE / HERTZ
<br /> 5424 VHB 100% MODEL 7000 SERIES FOR 48"x24" MODULE OR APPROVED BY ROY ASSOCIATES OR MATCH EXISTING. G. CONTRACTOR SHALL. HAVE A WORKERS COMPENSATION INSURANCE CERTIFICATE ON FILE WITH THE AC AIR CONDITIONING UNIT
<br /> BUILDING DEPARTMENT PRIOR TO ISSUANCE OF ANY PERMIT. N NEW (DARK)
<br /> (LIGHT)
<br /> CAPTIVE AIRE 430 PROVIDE HOOD HANGER. SEE MANUFACTURER DWGS. FOR MORE DETAIL ON CR T-BAR RETURN AIR AND GRILLES SHALL BE THE FIXTED BLADE FLUSH FACE TYPE .THEY SHALL BE
<br /> N SYSTEM OPEN BURNER 5'-0" 700 1920 14"0 0.794" STAINLESS STEEL 615
<br /> 3 RANGE AND OVEN
<br /> 424 ND2-PSP- 100% SHEET H-1, 2 & 3. INTERLOCK WITH EF-3 FABRICATED FROM STEEL, WITH WHITE PAINT, THE LAY-IN GRILLES SHALL BE METAL AIR MODEL H, NO INSTALLATION OF ANY PIPING OR EQUIPMENT TO BE INSTALLED PRIOR TO APPROVAL. OF PLANS 0 DIAMETER (DIA.) SCALE: AS INDICATED
<br /> ORHD SERIES OR MATCH EXISTING OR APPROVED EQUAL BY ROY ASSOCIATES. AND ISSUANCE OF PERMIT BY THE BUILDING DEPARTMENT. ARCH. ARCHITECTURAL DATE: 07-02_19
<br /> E) EXISTING DISHWASHER 8'-6" 600 1000 14"x14" - STAINLESSSTEEL (E) NOTE # 1 DWG. DRAWING
<br /> 4) . I
<br /> G
<br /> SMD SURFACE MOUNT CEILING DIFFUSERS FOR GYPBOARD CEILINGS SHALL BE THE SAME AS CD 2. FIRE EXTINGUISHER LISTED AND LABELED FOR CLASS K FIRES SHALL BE PROVIDED AT AN FLR. FLOOR DRAWN BY: VS/WA/JB/GS
<br /> 100% SPECIFICATION ABOVE EXCEPT SURFACE MOUNTED. APPROVED LOCATION, TO BE DETERMINED PRIOR TO FINAL INSPECTION BY THE FIRE MARSHAL. ABV, ABOVE SR KS CHECKED BY: FP SP
<br /> NOTES: INSTALL WITHIN 30 FEET OF COMERCIAL FOOD HEAT-PROCESSING EQUIPMENT AS MEASURED CLG. CEILING / / /
<br /> ALONG AN UNOBSTRUCTED PATH OF TRAVEL, IN ACCORDANCE WITH CALIFORNIA CODE OF A.F.F. ABOVE FINISHED FLOOR SHEET No.:
<br /> 1. REGULATIONS PER 2016 CFC. COND. CONDENSATE
<br /> INSPECT AND SERVICE EXISTING KITCHEN HOOD AND ITS RESPECTIVE COMPONENTS IN ACCORDANCE WITH THE MANUFACTURER'S RECOMMENDATIONS. CLEAN FILTERS AND DUCTS, REPLACE THE DAMAGE GREASE FILTERS
<br /> BEL, BELOW
<br /> NEEDED.AS INSTALL METAL BLANKS AS NEEDED TO FILL THE VOID SPACES BETWEEN THESE FILTERS. TEST AND CALIBRATE ALL SAFETIES AND OPERATING CONTROLS.
<br /> CFM CUBIC FEET PER MINUTE
<br /> HP HORSEPOWER
<br /> SP. STATIC PRESSURE
<br /> LBS. POUND (WEIGHT) m
<br /> 1 ■
<br /> INFO. INFORMATION0
<br /> TYP. TYPICAL
<br /> CMC CALIFORNIA MECHANICAL CODE
<br /> CPC CALIFORNIA PLUMBING CODE SHEET 20 OF 33
<br /> CED CALIFORNIA ELECTRICAL CODE
<br /> NEC NATIONAL ELECTRICAL CODE
<br /> CBC CALIFORNIA BUILDING CODE
<br /> PROJECT No.: 19-020
<br />
|